2015 Ram 3500 Rear Wheel Seal

แชร์
ฝัง
  • เผยแพร่เมื่อ 21 ม.ค. 2025

ความคิดเห็น • 29

  • @irawaltman9572
    @irawaltman9572 ปีที่แล้ว +2

    Well you could have shown us the removal and instalation of the bearing races but I get the just of it. Thank u

  • @bobabooie6389
    @bobabooie6389 ปีที่แล้ว +2

    The deck screw trick is pretty cool. Thanks

    • @markmeeks2135
      @markmeeks2135  ปีที่แล้ว +1

      Your welcome! Glad it helped.

  • @davecarrow939
    @davecarrow939 ปีที่แล้ว +1

    Can I ask where did you get a manual that includes the real seal etc? The manuals from the parts store don't include this.

    • @markmeeks2135
      @markmeeks2135  ปีที่แล้ว

      I got a factory service manual many years ago.

  • @PGN21
    @PGN21 6 หลายเดือนก่อน

    What would happen if the seal would be put in the opposite direction its fits nice, thats how my trucks hub is assembled

    • @markmeeks2135
      @markmeeks2135  6 หลายเดือนก่อน

      @@PGN21 My guess would be that it would leak and cause premature bearing failure. Proper assembly is critical for long life of the bearings

  • @lagit2009
    @lagit2009 ปีที่แล้ว +1

    Thank you you did a great job. Mine is a 3500 dodge dually. Only thin on mine is we couldn't find the right seal! we Thought! found out it is the right seal but on mine you have to take the insert and that top cap off of the seal for it to fit. Other wise the center was to small. They must have change axel spinodal sizes and made them smaller on the newer trucks so they used the same seal but with the outer cap and a reducer.

    • @markmeeks2135
      @markmeeks2135  ปีที่แล้ว +1

      Glad everything worked out for you.

  • @mtsanchez27
    @mtsanchez27 หลายเดือนก่อน +1

    Which seal tool did you use to install the seal?

    • @markmeeks2135
      @markmeeks2135  หลายเดือนก่อน +1

      @@mtsanchez27 I didn’t use anything but a hammer and a small piece of wood.

    • @mtsanchez27
      @mtsanchez27 หลายเดือนก่อน +1

      @markmeeks2135 thanks!!

  • @blue67strm
    @blue67strm 2 ปีที่แล้ว +1

    Thank you for the video. Definitely helps

  • @set1215
    @set1215 5 หลายเดือนก่อน +1

    What do you call that socket from Napa and did you pack both bearings

    • @markmeeks2135
      @markmeeks2135  5 หลายเดือนก่อน

      @@set1215 I don’t know what the socket is called. I took the nut to Napa and told them what I was needing and they had it. As for the bearings yes I packed both bearings liberally. You must keep grease away from the seal mounting surface going into hub and on the axel lip. Grease on those surfaces will cause a leak. Use liquid dish soap on seal surfaces and on axel tube. The nut will come off relatively easily when you remove the key. So not a problem to get off and carry to Napa. Hope that helps you.

  • @johnsonvideos1450
    @johnsonvideos1450 8 หลายเดือนก่อน +1

    Hi what is the part number on the wheel seal thanks

    • @markmeeks2135
      @markmeeks2135  8 หลายเดือนก่อน +1

      There are 2 different ones. One is for single rear wheel and dual rear wheel. The dual rear wheel is (710563) from oreilly and the single rear is (710564) from Oreilly.

  • @albarino6
    @albarino6 2 ปีที่แล้ว +1

    I'm having trouble removing the hub. How did you remove it?

    • @markmeeks2135
      @markmeeks2135  2 ปีที่แล้ว

      Yes the hub is sometimes hard to remove. Just takes a little force to pull off. The seal is is holding it to the axel tube. The seal is a 2 piece seal and will most likely come apart. When you remove the outer bearing it will allow you to wiggle it around as you pull on the hub.

  • @wildalaskaadventuresandgam7106
    @wildalaskaadventuresandgam7106 11 หลายเดือนก่อน +2

    The bearings are lubed by gear oil on these. You’re not supposed to grease the bearings. Just wet them with gear oil.

    • @markmeeks2135
      @markmeeks2135  11 หลายเดือนก่อน +3

      Sir you are incorrect. Read the factory service manual.

    • @rsg1963
      @rsg1963 7 หลายเดือนก่อน

      You'll destroy the bearings if you don't use grease initially. It may seem weird, but it's industry standard.

  • @raulyravelo557
    @raulyravelo557 ปีที่แล้ว

    Hello

  • @marshgonz
    @marshgonz 10 หลายเดือนก่อน

    Great video, but you do not pack the bearings. By doing this, you have contaminated your gear oil, specially if you have minimal slip.

    • @markmeeks2135
      @markmeeks2135  10 หลายเดือนก่อน +4

      You are mistaken. According to the factory service manual the bearings are to be packed in grease before assembly.

    • @charlescoffey3337
      @charlescoffey3337 9 หลายเดือนก่อน +2

      Go right ahead and don’t pack the beating
      You will be on the side of the road
      With one hell of a problem
      Seen it a dozen times

    • @rsg1963
      @rsg1963 7 หลายเดือนก่อน

      You'll destroy the bearings if you don't use grease initially. It may seem weird, but it's industry standard.