I also have the riden 6018 and start to be tired of pressing buttons. Maybe i don t like to have to adjust current initially at 10mA digit I want knobs. Thanks fos sharing
by mistake i ordered this small one without fines i thought i had the 60v or the 30v10a one at 300watts.. anyway i m amateur and want it mostly for single charge cells and top balace em.. comonly 20/25 amps cells !!! hope with some patience this 150Watts will be ok
Will the amperage go down (while the output is on) if the device isn't connected to something that can receive the power? I tried connecting some lifepo4s to a model just like this and the amperage would always drop out to zero when I would adjust it on the output, even though it was all connected to the battery. 🤷 Thanks for any help u can give!
The Original Manufacturer is Zotech with its brand Zoyi, but you can find it as a rebranded one from Aneng, Bside or Richmeter. Exists 3 or 4 models, but on all rebranded one they are exactly the same.
I bought it! Confused, no manual! says get on line, no link and cannot find! Shipped showing 230volt on cord connection, just as yours is showing, it in 110 Volt connection when showing 220 or do I need to slide over to be 110 volt in America. Are you running 230 or 110volt. I set it for 30 volt and it lowers the voltage! I want constant voltage and limit the current. odd set up.
When Constant Current mode is ON then of course voltage has to go down - how could the power supply otherwise limit the current? You can't change the Ohm's law. Try setting 25 V and 200 mA and then short the leads. CC LED will be ON and the voltage on the display would be 200 mA times resistance of the leads. You can't have higher voltage than current times resistance. BTW, I've found the manual in just a few seconds.
@@ooltimuthis is lab bench power supply, which often not require to do more than 5A, if you need to power something greater than 5A this isn't the right tool because this tool is for diagnostic and testing small devices that need accuracy over big amps. You can buy a cheap 12V power supply with 40A and then step it up or down as you like if you need just big current without much accuracy.
ok... what about ripple? what about electrical noise?
I also have the riden 6018 and start to be tired of pressing buttons. Maybe i don t like to have to adjust current initially at 10mA digit
I want knobs. Thanks fos sharing
Very smart, to hold your hand in FRONT of the display, you will show...
by mistake i ordered this small one without fines i thought i had the 60v or the 30v10a one at 300watts.. anyway i m amateur and want it mostly for single charge cells and top balace em.. comonly 20/25 amps cells !!! hope with some patience this 150Watts will be ok
Hello, does it memorizes voltage and current when power down and off?
Or do you have to set it at each startup ?
Thanks
Wird gespeichert.
Will it do constant voltage and constant current? Ta
Can you put power in a shorted pcb to see what is going hot and find faulty shorted component?
Will the amperage go down (while the output is on) if the device isn't connected to something that can receive the power? I tried connecting some lifepo4s to a model just like this and the amperage would always drop out to zero when I would adjust it on the output, even though it was all connected to the battery. 🤷 Thanks for any help u can give!
Can you disable the beep you hear when turning the knobs?
Desolder the beeper on the pcb. I made the same with several ups units
No, i have seen an aliexpress video where you have to press and hold a knob and you can set luminescity of the display and beep sounds.
Hi are you still happy with Power Supply?
Faster than old model looks ok on bangod cost 75 but on ali only 45£ :/
Kad si već iz HR. Jel bilo carine?
Nije, slali su iz eu skladista
Gentlemen can you share the brand for your Multimeter in this video and the model number? Thanks in advance!
It’s visible in the video: Aneng AN-999S
The Original Manufacturer is Zotech with its brand Zoyi, but you can find it as a rebranded one from Aneng, Bside or Richmeter. Exists 3 or 4 models, but on all rebranded one they are exactly the same.
Hi, I'm not getting any continunity reading on the power bench when I put multimeter probes and crocidile clip together. Any idea why, thanks.
Fantastic, arrive today, it's incredible
Hello friend. Is it still working fine? Did you have a problem with her? I'm Brazilian :D
Ottimo ho preso il modello da 10 ampere encoder precisi con regolazione anche fine dei valori
jel još uvijek radi, nakon 2 godine . pozz
da, radi bez greske, ne palim ga cesto ali jos uvijek radi
Excellent product
I bought it! Confused, no manual! says get on line, no link and cannot find! Shipped showing 230volt on cord connection, just as yours is showing, it in 110 Volt connection when showing 220 or do I need to slide over to be 110 volt in America. Are you running 230 or 110volt.
I set it for 30 volt and it lowers the voltage! I want constant voltage and limit the current. odd set up.
it need to be set like voltage in your country, my is set to 230. (230 is visible) .
When Constant Current mode is ON then of course voltage has to go down - how could the power supply otherwise limit the current? You can't change the Ohm's law. Try setting 25 V and 200 mA and then short the leads. CC LED will be ON and the voltage on the display would be 200 mA times resistance of the leads. You can't have higher voltage than current times resistance. BTW, I've found the manual in just a few seconds.
I'm more confused reading wtf u sayin
nice
Wait is this linear or switching psu ?
Should be obvious
2:00 lol... are you american or something ? measuring things with everything but a ruller xD
Can you use it at more than 5 amps when the voltage is lower than 30V? For example 10V 15A?
Of course not
@@МаксОгн why? it would be nice
@@ooltimu max is 5A out...
@@ooltimuthis is lab bench power supply, which often not require to do more than 5A, if you need to power something greater than 5A this isn't the right tool because this tool is for diagnostic and testing small devices that need accuracy over big amps. You can buy a cheap 12V power supply with 40A and then step it up or down as you like if you need just big current without much accuracy.
5a is cc limit duh
"This way i can be much faster", then it took literally 15 seconds to set the voltage to 3.5V :D
Português