Good rough guide. I just installed this kit onto my gen1 700 5r in .308. In addition to what this fella did, I had to dremel the magazine at the front and back a bit to get it seating properly as it was interfering with the receiver at the rear and under the feed ramp. This is with the factory HS Precision stock. Feeding is fine. Extraction is a bit stiff but I'm sure it will break in. So far I can recommend this upgrade.
I did the same grinding off with those two tabs front and rear. I modified my factory plastic SPS stock. All worked well. Still hunting with my two factory plastic stocks these days. Life is Good!! Magpul makes good stuff! Peace Be The Journey!
Maybe not the best video I've ever seen but truly helpful. I now know absolutely that there's no way I'd install this part on my rifle. There's a reason the legit companies charge more than $30 for a bottom metal.
This bottom metal is originally designed to work with the magpul 700 hunter stock. It's not drop-in for anything else, hence the modification needed to make it work.
You say it works "pretty well" on your sps stock. What do you mean by that?Id like to do this to my sps but if the magpul one doesnt work perfectly,ill get a different brand.
Will Robinson it works well if it's better for you lol. Keep in mind that the original stock is not the better one for accuracy. It's fine for what i do with it.
Gt Rul3s Thanks for the reply. As long as it works, thats good enough for me. As far as accuracy goes , the original stock will do just fine for me too.
I did this to my Remington 700 SPS Tactical with the original Hogue molded stock recently. Once installed my bolt made contact with the top of the magazine. I had to shim between the bottom metal and rifle stock with a washer to drop the mag down just slightly. Just in case anyone runs into that...
Perfect video, I've been looking for one like this for about a week. Restored my confidence that I could do it myself to my savage axis that I'm putting in a Boyd's Pro Varmint. Excellent job Devil!!!
Nothing looks better on a nice rifle than a polymer trigger guard (eye roll). Been through two polymer "bottom metal" setups. One for a savage 110, and one for a howa 1500 after the howa plastic bottom metal cracked while i was torquing the action screws with a torque driver. Both of my aftermarket polymer bm cracked at the center action screw. Shims on the back did not prevent the cracking. Threw all three in the trash, bought CDI actual metal bottom metal, and haven't looked back.
My DBM and extra mags are on the way. Going to WECSOG the DBM into my HS-Precision stock for my .308 SPS Tactical and your video was a HUGE help and inspiration. I hope to have my own video up next week and for sure will have you in my shoutouts on it.
Thinking of this for a Bergara b14 300win. Bergara makes a kit for about $150 but its always out of stock. The Magpul is about $80. Thanks for the video. Any follow-ups on cycling live ammo?
I did this with my Bell & Carlson stock. But, I left the vertical magazines guides! The rear one leave alone, front one cut down to just rest on top of bedding block. On the rear one! Just remove the tang behind the guide. In doing this, it clears the bridge of the bedding block. You only have to bevel the bridge a small amount to clear. Go extremely slow, and check and check some more before taking off material. I ended up with a super close to factory look. And my magazines have support front to rear and function perfect. To get that nice clean close fit! Final fit with a file and sandpaper. Just my two cents.
"Thumbs Up" for your disclaimer 😆 Great video on "rough opening" install of this bottom metal magazine. Even better with your GoPro view. Hell, you even showed your imperfections which to me, is really nothing to worry about...my rifle is a nice tool and small imperfections make her more beautiful. Thanks for the tip about the Timney flat trigger issue...I have the Timney Calvin Elite flat trigger. I can probably see this going to happen on my R700. Still deciding between a few different bottom metal magazine companies. Thanks a lot for this video. Subscribed to you, my friend.
Nice video -- how has it held up over the years? Considering how much work was involved wouldn't it have been easier to just buy the Magpul 700 hunter stock -- or was it not out at this time?
Awesome video, you inspired me to modify my SPS Tactical a little bit ago! I used a little CNC mill I have to do all the cutting, but same project basically. I put together a little video over at my channel of how I did it, and I'm getting ready to do the mod again on another rifle; one almost the same as yours! Keep up the good work, thanks!
I've been thinking about doing this but my stock on my rem 700 doesn't have bottom metal. I wish there was more info on milling it out to fit bottom metal. I don't want to ruin my stock either considering I fiberglass bedded and freefloated it myself and after all that time and work if hate to end up throwing it away
Excellent video I bought the ATI Legacy, fit perfect but the magazine is crap, Push down on the follower and it stays down, may switch to Magpul but found a metal piece from CD Precision and they will do the inletting at no additional charge. For the tools, time and talent that you have, the $209 investment to get the metal piece mahbe a bargain..Great video
So when you finished it looks like the Bottom metal is sitting even or in front of the chamber face, I was looking at mine and just wondering if it needs to be in line perfectly or not.
Just wondering if you have had any experience doing this to a Remington 700 VTR? I have read that this drop in is almost a perfect fit for the VTR stock with little or no modification. Thanks.
bvhnightmare ah lol wondered why magpul called it a metal. lol searching I didn't find it and always brought it up. Looking to do this to my sps Tactical.
I used a cargo net that had small squares. painted once then went back over again using different colors. example. if I went: sand, light green, brown, OD. I would go back over a second time in the opposite order.
Nice! I'm sorta cheap so a $200 bottom metal with $115 magazines isn't really my style. So this new magpul stuff with $35 bottom metal and $40 mags is great.
Watching this video makes me wonder how popular the Mossberg MVP 556 and 308 have become? They seem like pretty good setups and look to come in many different flavors. Plus taking AR15 mags and SR25/LR308/M1A mags, respectively, isn't a bad deal either. Anybody want to weigh in on this?
Viiking 01 to be honest I think it not really going to take off even two year today I’ve seen one in a gun store and one at the range and I go quite a bit. If you need more then 3-5rd you really need a semi auto for that type of engagement. I do like the ability to reload quickly in the hunt but it not that much faster them me slinging 4 more rds into the well.
Hey bvnightmare Thanks for the great video! Since they announced the hunter 700 stock and bottom metal at shot show I have been wondering if it is possible to install their bottom metal into my Bell and Carlson stock. This video does a very good job explaining it but I am wondering if you could send me some more detailed pictures of the inside of the stock and bottom metal how you have it set up now and some pictures of how the original bottom metal fits into the inletted stock. Maby even do another video more detailed of how it turned out and a closeup of the inside of the stock and bottom metal of how it is set up now. That would be super sweet I am so happy that someone had the nuts to take a $300 dollar stock and go dremel at it and try to get this bottom metal to fit and work and i love it! Thanks again dude... I private messaged you to my email where you could send me some picture and stuff that would be friggin awesome!
you wont ruin any of the "structural integrity" by removing a small amount of material from the inside edge of the block. if you were going to hacksaw a channel all the way through it, now that would effect things
this wasn't made to use in anything other that the Magpul hunter 700 stock so do this at your own risk. once you dremel your stock the original trigger guard and floor plate will not work with that stock anymore
bvhnightmare Thank you. I'm still to find a metal Magpul mag well. Brownell, Midway they all are coming up as a polymer. The only metal ones I have found are by Surgeon, Badger, or HS Precision.
dkorzo1 I am sorry I misspoke in my previous comment Magpul only manufacturers polymer bottom units I have found through hundreds of rounds with the Magpul in my Remington 700 that it is just as good or better as the metal bottom metals
Sig 226/2022 not only that, why wouldn't you. that's like saying my tires have air in em already, y inflate them to the right psi? Y, because that's how u do it correctly. not half assed.
James Autry I put the rifle together before Magpul ever came out with their stock instead of buying a whole nother stock I've decided to modify my existing one
The Magpul Kit Magazine kit is specifically made for the Magpul Hunter 700 Stock. You can buy a kit from Legacy Sports that does not require any modifications. I bought mine from there and it fits perfect and no mods were required for fitment. I've had mine for about 2 months now. I've put 50 rounds through it and it works like a charm. No slack. fits like a glove. and worth it. legacysports.com/shop/products.php?cat=8
that is true Legacy Sports does make a bottom metal kit for the Remington 700 but the plastic quality compared to Magpul is poor also I do not like the way their magazine release system is setup the Magpul bottom metal allows me to run Accuracy International magazines, the Legacy Sports magazine is a good option if you do not want to modify your stock
bvhnightmare Nice. Hope you love your kit. Just didn't know if you saw the legacy kit. Just had to let ya know. Do you know any great websites for gun stocks?
+Don Lemke I had a friend who shot a rifle with a legacy Sports bottom metal and I just didn't like it that's why I tried the Magpul bottom metal on the subject of gun socks no I do not have any good websites sorry
Is your stock the bell & carlson hook stock? If so then I got the same stock aswell and am glad you didn't have to Dremel any of the aluminum bedding out for this mod! Great video.
you don't have to do all that advance technology industries makes. a magazine conversion kit for Remington short action cal 223,204,308, 22-250 drop in ready only $99.00
There are several things I do not like about the ATI. 1: the mag release is in front of the magazine, if you do any sort of barricade work you will drop your mag. Also the mag release is flimsy 2, it is not compatible with AICS mags. 3, there is no metal reinforcement on the bolt holes so improper torque will be applied to your action thus causing accuracy issues. just not what I was looking for.
Sorry, once@time. Even a brief thought about firearms is illegal in Kalifonia. Always remember: Gun control is the present governmental power surrendering the Liberty of the law-abiding citizenry to the criminal element...
[kirk west] I actually haven't, but just checked it with my Hogue stock and it is very much touching... That'd be a good mod, let me see what I can come up with.
SP-ATech thanks man I hunt with my rifle so I like the lightweight Hogue. I haven't seen much info on it I'm curious if sanding or taking a dremel to the end of it would fix this. I can't afford to mess up my stock so I'm just waiting to see somebody else do it
Good rough guide. I just installed this kit onto my gen1 700 5r in .308. In addition to what this fella did, I had to dremel the magazine at the front and back a bit to get it seating properly as it was interfering with the receiver at the rear and under the feed ramp. This is with the factory HS Precision stock. Feeding is fine. Extraction is a bit stiff but I'm sure it will break in. So far I can recommend this upgrade.
I did the same grinding off with those two tabs front and rear. I modified my factory plastic SPS stock. All worked well. Still hunting with my two factory plastic stocks these days. Life is Good!! Magpul makes good stuff! Peace Be The Journey!
Maybe not the best video I've ever seen but truly helpful. I now know absolutely that there's no way I'd install this part on my rifle. There's a reason the legit companies charge more than $30 for a bottom metal.
This bottom metal is originally designed to work with the magpul 700 hunter stock. It's not drop-in for anything else, hence the modification needed to make it work.
Looks good 👍🏽
Beautiful rig you got there Sir. I like how you got to the point of of installing the mag well
Thanks for your advice. It work pretty well on my original sps stock.
Gt Rul3s any pics or links to the work? im debating on doing this to my sps stock.
mrhertz760 sure! Give me your email and ill send you few pictures!
You say it works "pretty well" on your sps stock. What do you mean by that?Id like to do this to my sps but if the magpul one doesnt work perfectly,ill get a different brand.
Will Robinson it works well if it's better for you lol. Keep in mind that the original stock is not the better one for accuracy. It's fine for what i do with it.
Gt Rul3s Thanks for the reply. As long as it works, thats good enough for me. As far as accuracy goes , the original stock will do just fine for me too.
I did this to my Remington 700 SPS Tactical with the original Hogue molded stock recently. Once installed my bolt made contact with the top of the magazine. I had to shim between the bottom metal and rifle stock with a washer to drop the mag down just slightly. Just in case anyone runs into that...
Ty, do you like the modification?
Are you still happy with it? I'm thinking about doing this and I have the same stock you mentioned.
Perfect video, I've been looking for one like this for about a week. Restored my confidence that I could do it myself to my savage axis that I'm putting in a Boyd's Pro Varmint. Excellent job Devil!!!
Cameron Miles thanks for the kind words
Awesome to know that this works! And I was thinking of getting a $900 chassis just so I can use mags. Now I won't have to.
The Magpul Hunter stock is still a good option, for 200$ you have a stock that can receive a bottom mag. That's what I'm gonna do with mine
stephane Blondiau they need to make the Hunter stock in a Left hand configuration!
@@chetburnes3776 yep, I'm not concerned about that but it can be a good option too
Great no nonsense video & thanks for sharing...
"I am in no way responsible for your fuck ups." Witnessing a lawyer reading that... priceless.
Nothing looks better on a nice rifle than a polymer trigger guard (eye roll).
Been through two polymer "bottom metal" setups. One for a savage 110, and one for a howa 1500 after the howa plastic bottom metal cracked while i was torquing the action screws with a torque driver. Both of my aftermarket polymer bm cracked at the center action screw. Shims on the back did not prevent the cracking. Threw all three in the trash, bought CDI actual metal bottom metal, and haven't looked back.
Did the very same thing to my houge.....works flawlessly.
Good to hear I just bought one to add to my Houge.
You still happy with it? Thinking about trying it ont the same stock.
My DBM and extra mags are on the way. Going to WECSOG the DBM into my HS-Precision stock for my .308 SPS Tactical and your video was a HUGE help and inspiration. I hope to have my own video up next week and for sure will have you in my shoutouts on it.
thank-you for the kind words!
Thinking of this for a Bergara b14 300win. Bergara makes a kit for about $150 but its always out of stock. The Magpul is about $80. Thanks for the video. Any follow-ups on cycling live ammo?
I did this with my Bell & Carlson stock. But, I left the vertical magazines guides! The rear one leave alone, front one cut down to just rest on top of bedding block. On the rear one! Just remove the tang behind the guide. In doing this, it clears the bridge of the bedding block. You only have to bevel the bridge a small amount to clear. Go extremely slow, and check and check some more before taking off material. I ended up with a super close to factory look. And my magazines have support front to rear and function perfect. To get that nice clean close fit! Final fit with a file and sandpaper. Just my two cents.
"Thumbs Up" for your disclaimer 😆
Great video on "rough opening" install of this bottom metal magazine. Even better with your GoPro view. Hell, you even showed your imperfections which to me, is really nothing to worry about...my rifle is a nice tool and small imperfections make her more beautiful. Thanks for the tip about the Timney flat trigger issue...I have the Timney Calvin Elite flat trigger. I can probably see this going to happen on my R700. Still deciding between a few different bottom metal magazine companies. Thanks a lot for this video. Subscribed to you, my friend.
Does Remington have a reason for only producing internal magazine for model 700 rifles? Just wondering.
Nice video, thanks for taking the time to share!
Why not file down on the DBM instead of the stock?
I just got the adl Varmint bought the bdl stock and mag conversation kit not fitting needed
Awesome. Now I just need to find one for a long action
To remove .003 of an inch you would be using sand paper and not a Dremel tool
really that's the average thickness of a slice of notebook paper.
3 1/10 tenths of an inch... .300 of an inch
Nice vid. I'll be doing the same on my long range.
Did it work?
I want to do it too, on my B&C stock.
Looks good besides the bedazzled mag.
Love the intro “I am not responsible for your fuck up. Don’t be stupid” lol
Enjoyed the video. Very informative.
Thanks..
Nice video -- how has it held up over the years? Considering how much work was involved wouldn't it have been easier to just buy the Magpul 700 hunter stock -- or was it not out at this time?
Plug n play with Magpul Hunter 700 and Magpul magazine well
2 screws
Yea that magpul stock is junk rather have h and s any day
You just saved me $$$ Thank you for the video.
Just keep grinding ..... what can possibly go wrong. Dremel Degree !
pawpawtx as you can see my engineering skills are on point
Great video easy to follow.
Awesome video, you inspired me to modify my SPS Tactical a little bit ago! I used a little CNC mill I have to do all the cutting, but same project basically. I put together a little video over at my channel of how I did it, and I'm getting ready to do the mod again on another rifle; one almost the same as yours! Keep up the good work, thanks!
I've been thinking about doing this but my stock on my rem 700 doesn't have bottom metal. I wish there was more info on milling it out to fit bottom metal. I don't want to ruin my stock either considering I fiberglass bedded and freefloated it myself and after all that time and work if hate to end up throwing it away
yea I understand, a better option might be the magpul stock
I thought the same thing about more milling info, but I just had to create the CNC milling programs to get mine done.. Worked great tho!
The f bombs really set this how to video apart from the others.
Anything you would do different? Going to try this in a week
Best disclaimer ever
Great video dude👍
Nice job
Excellent video I bought the ATI Legacy, fit perfect but the magazine is crap, Push down on the follower and it stays down, may switch to Magpul but found a metal piece from CD Precision and they will do the inletting at no additional charge. For the tools, time and talent that you have, the $209 investment to get the metal piece mahbe a bargain..Great video
Does this use regular 308 magpul mags or short action AICS magpul mags?
Aics
@@bvhnightmare thanks 👍
So when you finished it looks like the Bottom metal is sitting even or in front of the chamber face, I was looking at mine and just wondering if it needs to be in line perfectly or not.
Just picked one up. Are the actualy polymer? I can’t seem to find an actual metal magpul bottom plate. Sorry for the ignorance
Looks good.
Just wondering if you have had any experience doing this to a Remington 700 VTR? I have read that this drop in is almost a perfect fit for the VTR stock with little or no modification. Thanks.
sorry i do not.
Magpul could make so much money selling this if it just fit directly into a factory 700 stock (or at least factory dimension aftermarket stock).
cfusionpm yes, but they sell it with the I tent of you using it in their chassis system
bvhnightmare can you put a link to it
I'd be interested to know how it shoots after the mod.
update video will be soon
+Al Enzbigilis new video is up
I bought same thing hours ago and I realized Magpul well only fit it own Hunter 700 stock.
Hi bvhnightmare! Thank you so much for your videos! Can you tell what is the name of the stock you are using and is it better than the magpul hunter?
the stock is a Bell and Carlson and I have not used the magpul
Can't find this one. All I find is the polymer one for the magpul stock. You have a part #
Gary Leafty this is the polymer one.
bvhnightmare ah lol wondered why magpul called it a metal. lol searching I didn't find it and always brought it up. Looking to do this to my sps Tactical.
Works great, I just finished up my SPS Tactical so it'll work. I think they're talking about the release catch, that's metal...
But it’s all good I just bought this and the hunter stock for my 700 ADL 6.5cm with a 24” threaded heavy barrel
What did you use when you sprayed your stock to get the square shapes in contrasting colors?
I used a cargo net that had small squares. painted once then went back over again using different colors. example. if I went: sand, light green, brown, OD. I would go back over a second time in the opposite order.
I just did this to my 5r gen 2 last night. My mag doesn't want to seat with the bolt shut without giving it a good slap.
What caliber? I’m thinking of doing this to my 5r in 308
Thanks for the vid, I have a 700 police that i wanna do this for.
Octavio Ortiz since this video I have done it to 2 other rifles
Thanx, I was going to buy a new stock until i saw your video. Now il will do this. Thanx great Video!
thx nice video i think ill fit one in my choate tool stock !!!
Any idea if I can put this on my bergara b14 hunter?
Thanks.
This thing still trucking along alright? I've got a left hand 300WM I'd like to do this to.
Jacob Whittaker yes it is I have 2 precision rifle matches through this and hundreds of rounds and it's still going
Nice! I'm sorta cheap so a $200 bottom metal with $115 magazines isn't really my style. So this new magpul stuff with $35 bottom metal and $40 mags is great.
Jacob Whittaker where did you find these for $35? 65 to 70 seems all I find.
T S my local gun shop sells just the bottom metal without the mag.
T S
$65-70 is WITH the mag....and bottom metal
Watching this video makes me wonder how popular the Mossberg MVP 556 and 308 have become? They seem like pretty good setups and look to come in many different flavors. Plus taking AR15 mags and SR25/LR308/M1A mags, respectively, isn't a bad deal either. Anybody want to weigh in on this?
Viiking 01 to be honest I think it not really going to take off even two year today I’ve seen one in a gun store and one at the range and I go quite a bit. If you need more then 3-5rd you really need a semi auto for that type of engagement. I do like the ability to reload quickly in the hunt but it not that much faster them me slinging 4 more rds into the well.
I have the MVP in 556. It has failure to fire issues with 556. Its not worth the money. About to trade in for one of these.
bvhnightmare what are the chances you would sell your old bottom metal?
Josh Boggess 0 cause I threw it in the trash
bvhnightmare no!! Those things have been hard to find.. thanks for responding
Josh Boggess I just finished up this same mod and I think I have mine, you still need one??
Update?
Hey bvnightmare Thanks for the great video! Since they announced the hunter 700 stock and bottom metal at shot show I have been wondering if it is possible to install their bottom metal into my Bell and Carlson stock. This video does a very good job explaining it but I am wondering if you could send me some more detailed pictures of the inside of the stock and bottom metal how you have it set up now and some pictures of how the original bottom metal fits into the inletted stock. Maby even do another video more detailed of how it turned out and a closeup of the inside of the stock and bottom metal of how it is set up now. That would be super sweet I am so happy that someone had the nuts to take a $300 dollar stock and go dremel at it and try to get this bottom metal to fit and work and i love it! Thanks again dude... I private messaged you to my email where you could send me some picture and stuff that would be friggin awesome!
thanks man, I'll try and do a update video this weekend
AWESOME!!! You are the man!!! Much appreciated!
+Logan Nowak new video is up
Very cool, thanks for sharing!
Is there any metal in the magpul piece?
Troy Clark the bolt holes have metal reenforcement and that's it. the rest is polymer
Safety Glasses next dude....good video too.
How we can buy it ? Ours in thailand
I really wish I had the balls to do this!
you wont ruin any of the "structural integrity" by removing a small amount of material from the inside edge of the block. if you were going to hacksaw a channel all the way through it, now that would effect things
I understand that, I didn't affect how my stock worked but others may have a problem
thank you Mister ; it's perfect .
Delphdom.
this wasn't made to use in anything other that the Magpul hunter 700 stock so do this at your own risk. once you dremel your stock the original trigger guard and floor plate will not work with that stock anymore
Captain Howdy yea that is true
bvhnightmare nice job though
can you do this with a 700adl in .243?
Yes
would this mag fit into a standard r700 sps tactical stock?
+brayden hepworth yes it can, BUT, it will require modification of the stock
What make
of cheek riser is that?
Ebay kydex cheek riser
Where did you find the metal mag receiver? I keep running into the polymer version.
dkorzo1 they are all metal as far as the Magpul ones
bvhnightmare Thank you. I'm still to find a metal Magpul mag well. Brownell, Midway they all are coming up as a polymer. The only metal ones I have found are by Surgeon, Badger, or HS Precision.
dkorzo1 I am sorry I misspoke in my previous comment Magpul only manufacturers polymer bottom units I have found through hundreds of rounds with the Magpul in my Remington 700 that it is just as good or better as the metal bottom metals
bvhnightmare Thank you for the clarification.
bvhnightmare By the way, Bad Ass looking rifle!
For the price it should be a drop in fit. Is this a generic type plastic bottom?
Use some bedding to fill the cracks if you have any left
Sig 226/2022 I'm getting half minute of angle accuracy out of the rifle already so I don't feel there's a need to bed the bottom metal
bvhnightmare
Not for accuracy!
Just to fill the cracks. It would bother me every time I saw it if it was on my rifle 🤓
Sig 226/2022 not only that, why wouldn't you. that's like saying my tires have air in em already, y inflate them to the right psi? Y, because that's how u do it correctly. not half assed.
this mag upgrade is for the magpul hunter 700, why not just purchase a drop in upgrade instead of doing the gun smithing for the mag pul
James Autry I put the rifle together before Magpul ever came out with their stock instead of buying a whole nother stock I've decided to modify my existing one
Will this allow it to accept aics magazines?
Gunmonkey5 yes
Will this work using the hogue original stock??
Yup, just retrofitted the magwell on my Rem 700 Tactical to a Mappul setup
Which sling is that?
It is a generic gander mountain sling
The Magpul Kit Magazine kit is specifically made for the Magpul Hunter 700 Stock. You can buy a kit from Legacy Sports that does not require any modifications. I bought mine from there and it fits perfect and no mods were required for fitment. I've had mine for about 2 months now. I've put 50 rounds through it and it works like a charm. No slack. fits like a glove. and worth it.
legacysports.com/shop/products.php?cat=8
that is true Legacy Sports does make a bottom metal kit for the Remington 700 but the plastic quality compared to Magpul is poor also I do not like the way their magazine release system is setup the Magpul bottom metal allows me to run Accuracy International magazines, the Legacy Sports magazine is a good option if you do not want to modify your stock
bvhnightmare Nice. Hope you love your kit. Just didn't know if you saw the legacy kit. Just had to let ya know. Do you know any great websites for gun stocks?
+Don Lemke I had a friend who shot a rifle with a legacy Sports bottom metal and I just didn't like it that's why I tried the Magpul bottom metal on the subject of gun socks no I do not have any good websites sorry
Can you do it to the rubber stock
Luis Rodriguez not sure sorry
Is your stock the bell & carlson hook stock? If so then I got the same stock aswell and am glad you didn't have to Dremel any of the aluminum bedding out for this mod! Great video.
Andrew Garcia it's the B&C light tactical.
bvhnightmare sweet!
Anyone tried this on Remington factory BDL stock yet? Go? No go?
Should've done it indoors man lol
Awesome! What muzzle brake do you have?
posjoey it used to be a generic 3 chamber brake now I use a Badger fte mini
Where's the safety glasses, dammit!
you don't have to do all that advance technology industries makes. a magazine conversion kit for Remington short action cal 223,204,308, 22-250 drop in ready only $99.00
There are several things I do not like about the ATI. 1: the mag release is in front of the magazine, if you do any sort of barricade work you will drop your mag. Also the mag release is flimsy 2, it is not compatible with AICS mags. 3, there is no metal reinforcement on the bolt holes so improper torque will be applied to your action thus causing accuracy issues.
just not what I was looking for.
bvhnightmare and to add to that, the magazines follower in the ATI need to be sanded and the polymer is crap
Is this magazine illegal in California??
Sorry, once@time. Even a brief thought about firearms is illegal in Kalifonia. Always remember: Gun control is the present governmental power surrendering the Liberty of the law-abiding citizenry to the criminal element...
The new timney hit trigger is made just to fit this bottom metal ! 209$
Would this same process work on the Hogue stock 308
It works on my Hogue stock! I modified it a bit differently, but a magazine is a great addition to the rifle!
SP-ATech have you done any modification to keep the barrle channel free floating?
[kirk west] I actually haven't, but just checked it with my Hogue stock and it is very much touching... That'd be a good mod, let me see what I can come up with.
SP-ATech thanks man I hunt with my rifle so I like the lightweight Hogue. I haven't seen much info on it I'm curious if sanding or taking a dremel to the end of it would fix this. I can't afford to mess up my stock so I'm just waiting to see somebody else do it
SP-ATech watch the first half I'm gonna try this when I get my new mag kit in very soon . th-cam.com/video/HsQUwzEqvQc/w-d-xo.html
great video sir
Wer safety glasses while using power tools please
Thanks for the vid
WIsh i knew this could be done before I bought the PTG dbm... F*ck!!!
Bottom metal from Magpul is more like “plastic”
My drunk ass managed to inlet a Choate for a Magpul DBM. Don’t be a coward and just do it
Lost me at "Strutual" LOL
bvhnightmare no worries my man just messin with ya, i myself am not a speller either . Happy shooting !
"DREMILL"
what kinda of scope do u have on your rifle
magwell..
southerner985 thanks