If you save the calibration, can you avoid needing to calibrate at each use? My SAA-2N says to calibrate each time, even though there are several save slots for saving the calibrations.
Does any one know what the values are for the surface mount resistors they send with the unit . i got them solderd on but dont know wich one is the 5ohm 50ohm or 300ohm
Fabulous video, thank you - you've single handedly filled a huge gap in the user manual technical info. 👍 Regarding the HW Cal, is this a simple touch-screen button pressing exercise (once only) or are hardware configurations required (switch/es) inside the mini1300? The reason I ask is because, in my drive for online information I've found the FAA-450 EU1KY analyser with a good manual, and whilst this kit is not exactly the same as the mini1300, it's archetecture bears a striking resemblance. In the FAA manual it talks about changing a jumper on the RF board to do the HW cal. Thanks in advance. 👍
Hi there, would you mind giving me the measurements of the screen, hight/width please, I don't know if the measurements given are diagonal or not. All they seem to say in sales blurb is that it has a 4 inch screen. Many thanks
hola buenos dias tengo este analizador mini 1300 y se me ha quedado bloqueado en pantalla y me sale las letras CFG flush falled to open config file .err 13 sisem halted y no encinde y no se que puedo hacer con el por favor haver si me acosejas algo muchas gracias
This is the best and only English explanation of calibration I have found, thank you so much for taking the time to enlighten. Question: Do I run Hardware Cal (only on first run) first or was that done at factory?
I know im asking randomly but does anyone know a way to log back into an Instagram account?? I was stupid forgot my account password. I would appreciate any assistance you can offer me
@Kylo Ramon thanks for your reply. I found the site on google and im trying it out now. I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.
Anyone use this on their 23cm setup? I seem to have SWR results that are all over the board. The unit goes berserk above 1000mhz even into a dummy load. Anyone have any success?
Just can't make everyone happy. There would be many more complaints without music. Just be thankful. Your like all the people who think only their opinion matters and no matter what won't be happy
Just got my Mini1300 on friday after 3 month of waiting. Can't say thank you enough for your videos !
Did not find anything on the Internet about calibration Thank you I helped you! Thank you from Siberia!
You are welcome, from me.
Thanks for taking the time to make and post this video
You are welcome. Sorry for the delay
Guy has a killer voice!!
If you save the calibration, can you avoid needing to calibrate at each use? My SAA-2N says to calibrate each time, even though there are several save slots for saving the calibrations.
Does any one know what the values are for the surface mount resistors they send with the unit . i got them solderd on but dont know wich one is the 5ohm 50ohm or 300ohm
Hey did you eventually find out the values of mount resistors? I’m surprised no one knows.
The open one is easy, the 50ohm has an insulator the 5ohm is short
easy but you helped me @@VtecDriver
You didn't show which stub to use for what calibration.
Today no one will tell you. Shame that important information doesn’t come with the manual.
Seriously? At the end it shows each one
I don't know how to tell which dummy load that comes with the kit is the 50ohm load
where could you buy the calibration sma adaptors -
Fabulous video, thank you - you've single handedly filled a huge gap in the user manual technical info. 👍 Regarding the HW Cal, is this a simple touch-screen button pressing exercise (once only) or are hardware configurations required (switch/es) inside the mini1300? The reason I ask is because, in my drive for online information I've found the FAA-450 EU1KY analyser with a good manual, and whilst this kit is not exactly the same as the mini1300, it's archetecture bears a striking resemblance. In the FAA manual it talks about changing a jumper on the RF board to do the HW cal. Thanks in advance. 👍
Hi there, would you mind giving me the measurements of the screen, hight/width please, I don't know if the measurements given are diagonal or not. All they seem to say in sales blurb is that it has a 4 inch screen. Many thanks
hola buenos dias tengo este analizador mini 1300 y se me ha quedado bloqueado en pantalla y me sale las letras CFG flush falled to open config file .err 13 sisem halted y no encinde y no se que puedo hacer con el por favor haver si me acosejas algo muchas gracias
Which cable can I use for Calibrate S21 Gain Calibration, simple a coax cable 50 ohm between VNA and Test Port?
I LIKE YOUR DISK 😁😁😁
Price is up there with conventional analyzers. And its really just a nanovna.. so idk ?
This is the best and only English explanation of calibration I have found, thank you so much for taking the time to enlighten. Question: Do I run Hardware Cal (only on first run) first or was that done at factory?
You only need to run one time
I know im asking randomly but does anyone know a way to log back into an Instagram account??
I was stupid forgot my account password. I would appreciate any assistance you can offer me
@Edgar Castiel Instablaster =)
@Kylo Ramon thanks for your reply. I found the site on google and im trying it out now.
I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.
@Kylo Ramon it did the trick and I actually got access to my account again. Im so happy:D
Thank you so much you saved my account!
Anyone use this on their 23cm setup? I seem to have SWR results that are all over the board. The unit goes berserk above 1000mhz even into a dummy load. Anyone have any success?
I made my own loads in the video, because the ones that come with the kit are not really good above 700 MHz.
I did, just around a few days ago, and the value of the testing results is almost equal to the KC-901V and the Rigol 815TG.
After intro, Started at about 0:35 without any setup info and totally skipped the initial calibration into 5 ohms. May be a problem but NOT good!
Yup. Sorry. I'll redo
Mohon dalam terjemahan bahasa indonesia agar kami bisa lebih mengerti
Any information about what you were doing or using would have been great. As it is, you owe me for 5 minutes of my time.
Okay. Agreed. Just tell me what you would like to know.
You tube isn't my thing, but clarifying info for other folk's, if I know, I'll share it
Nope, I'll buy the Rig Expert
What’s up with the Asian culture bow? Cultural appropriation?
Nope
I am an Asian I appreciate that he could speak my language and he didn't say anything bad to my culture we are welcome if he comes to our country.
Please do another video but without the thumping "background" music. It's not necessary in an instruction video.
Just can't make everyone happy. There would be many more complaints without music. Just be thankful. Your like all the people who think only their opinion matters and no matter what won't be happy