วีดีโอ

hola buenos dias tengo este analizador mini 1300 y se me ha quedado bloqueado en pantalla y me sale las letras CFG flush falled to open config file .err 13 sisem halted y no encinde y no se que puedo hacer con el por favor haver si me acosejas algo muchas gracias

I don't know how to tell which dummy load that comes with the kit is the 50ohm load

Please normalize your audio when making your videos, Thanks!

Nope, I'll buy the Rig Expert

If you save the calibration, can you avoid needing to calibrate at each use? My SAA-2N says to calibrate each time, even though there are several save slots for saving the calibrations.

Hi there, would you mind giving me the measurements of the screen, hight/width please, I don't know if the measurements given are diagonal or not. All they seem to say in sales blurb is that it has a 4 inch screen. Many thanks

Price is up there with conventional analyzers. And its really just a nanovna.. so idk ?

I LIKE YOUR DISK 😁😁😁

What a complete waste of time. Why would we want to watch someone soldering SMDs from several feet away. What is being soldered and where to?

w t f

where could you buy the calibration sma adaptors -

Does any one know what the values are for the surface mount resistors they send with the unit . i got them solderd on but dont know wich one is the 5ohm 50ohm or 300ohm

Fabulous video, thank you - you've single handedly filled a huge gap in the user manual technical info. 👍 Regarding the HW Cal, is this a simple touch-screen button pressing exercise (once only) or are hardware configurations required (switch/es) inside the mini1300? The reason I ask is because, in my drive for online information I've found the FAA-450 EU1KY analyser with a good manual, and whilst this kit is not exactly the same as the mini1300, it's archetecture bears a striking resemblance. In the FAA manual it talks about changing a jumper on the RF board to do the HW cal. Thanks in advance. 👍

can you provide some assistance on how to calibrate the mini 1300

You didn't show which stub to use for what calibration.

Mohon dalam terjemahan bahasa indonesia agar kami bisa lebih mengerti

Please do another video but without the thumping "background" music. It's not necessary in an instruction video.

where can i find follow on

Which cable can I use for Calibrate S21 Gain Calibration, simple a coax cable 50 ohm between VNA and Test Port?

What’s up with the Asian culture bow? Cultural appropriation?

Amazon says the 1300 is not in stocks so does anybody information on where I can purchase ty 7 3

can u show me the close up the antena calibrated please witch prongs do i need to solder them on??

I just bought one of these things. The directions seem to be a potpourri of languages and no mention of calibration. Do you know if there are any written procedures out there?

Anyone use this on their 23cm setup? I seem to have SWR results that are all over the board. The unit goes berserk above 1000mhz even into a dummy load. Anyone have any success?

Anyone use this on their 23cm setup? I seem to have SWR results that are all over the board. The unit goes berserk above 1000mhz even into a dummy load. Anyone have any success?

Did not find anything on the Internet about calibration Thank you I helped you! Thank you from Siberia!

After intro, Started at about 0:35 without any setup info and totally skipped the initial calibration into 5 ohms. May be a problem but NOT good!

Unboxing is a WASTE of TIME & ENERGY! Plug it in & Use it.

Any information about what you were doing or using would have been great. As it is, you owe me for 5 minutes of my time.

Guy has a killer voice!!

how has it performed? what is it like in full sunlight? bluetooth capable? phone connect? pc connect? thanks

Amazing channel!! Looking forward to seeing more from you. I recommend you google smzeus . c o m! It’s a great tool to have when your trying to grow your social media or promote your videos!

Hi, Can you make VDO how to use the MINI .1-1300Mhz or the .1-600Mhz Pls.

hello dear friend i would want to connect with your channel, brandkaizer@gmail.com +91-9811019393 please do respond

5G is killing the bees!! It causes cancer and is spreading the Kung flu. you're telling me it's a coincidence the cities that have 5G have a higher rate of covid.

Thanks for taking the time to make and post this video

0:12 sweety-girls.online

This is the best and only English explanation of calibration I have found, thank you so much for taking the time to enlighten. Question: Do I run Hardware Cal (only on first run) first or was that done at factory?

Just got my Mini1300 on friday after 3 month of waiting. Can't say thank you enough for your videos !

Hope you get new markers before your next lesson :)