I found a Sig suppressor for my MCX Spear LT and it is currently in jail! When I had called Sig, they didn’t have any in stock so I’m grateful that I found one.
Just filed paperwork on a Sig SLH 7.62 compact Ti can. I may leave it on after all. I figure I'll soak in water anyway. I have a 9L heated ultrasonic I can stick the barrel into and then put this in a barrel vise to spin it off if I get antsy waiting a year for approval to come in.
For me to remove the flash hide I put the tip of the barrel in boiling hot water and held it there for about 5-10 minutes. It was still VERY difficult to twist off I almost ended up breaking my desk with the vise lol. I wish Sig wouldn’t put rock set on all the flash hiders. But anyway really nice video thanks for checking mine out.
I guess there is a usecase for portability and maneuverability in close areas. The Rattler in 300AAC is probably the ultimate PDW and I am looking for parts to build an FDE one someday. I know you can get the black ones all day every day, so may have to settle for one of those.
Just stumbled upon your vids, couple of observations from my own experience. The button head torx screws for the forend will easily strip out if you torque them to 45 inch lbs., don't remove the flat head torx screws holding the retainer tab on the bottom of the forend, and finally, my Gisselle reaction rod does not fit the chamber on these guns. I had to ship my upper back to Sig to remove and replace the stripped torx screws on the forend and also asked them to remove the muzzle device as I run a DeadAir Sandman S. Customer service was great, they covered all shipping and turn around time was 4 days. They told me they have received bent and mangled receivers from customers who tried to remove the muzzle device without the proper tools.
Thanks for the information which is sorely needed. I have not yet tried to do anything with the muzzle device, and will look into sending to Sig for removal although I do have a dedicated barrel vice I could use to clamp down the barrel outside the receiver. Good to know on the handguard screws as well. Thanks for watching and for the useful info.
Little update. I removed the muzzle device by clamping the barrel (removed from upper and also removed the oprod to give me more room) in a dedicated barrel vice. I have bushings that enabled me to spin off the flash hider with a 3/4 socket and a few whacks with a dead blow hammer. Did not soak in water but if one doesn’t have a barrel vice, water soak is the only option.
The reason why so many strip the handguard screws is because they're NOT standard torx t15! They are Torx Plus IP15 screws. Wish Sig would note this !!
I’m in Texas…DFW area and bought that gun back in June….haven’t been to range yet because of the Dang heat.! I bought the retention piece recently but waiting until I get the gun out and shoot it first. What part of Texas are you living in?
I'm just North of Houston. Yeah I hear you about the heat. I've had 110 degree range days shortly after. It's brutal. Hope you get to shoot yours soon. Thanks for watching.
I believe in my case it was mostly if not all, the handguard flexing and not the barrel, as I took it on a range trip and put over 300 rounds through it in quick succession. I stuck it in a case and when i pulled it out at home the. handguard has flexed over to one side. A boresight confirmed the barrel was not affected. I ended up installing the Arisaka zero retention clamp and it really stiffened the entire thing up. In your case the 9” barrel and shorter handguard will have a much smaller lever moment so the issue should be less apparent. Will see over time if it happens again but will confirm zero next time I’m out just in case.
Haven’t heard of the raptor but if it’s anything like the current rattler then I will try to get one. I’m debating on SBR’ing this one and getting the 11.5 barrel as that is more my preference. Thanks for watching
You probably already have your answer but it's T15@ 35in-lbs for the handguard retention screws and T27 @60in-lbs for the barrel clamp. Torx of course.
The handguard screws are NOT standard torx t15, they are Torx plus IP 15. This is why so many strip the srews! Wish Sig noted this. Not sure on the Barrel screws...but I suspect the same ??
I was using the Blue Force Gear Vickers Sling (Combat Applications Sling) This one: www.blueforcegear.com/vickers-one-sling But I just set up and will use Edgar Sherman ESD sling here: www.weaponoutfitters.com/edgar-sherman-design-sling.html I've been using the BFG slings for years, but I like how compact sleek the Edgar Sherman ones are. Will give them a try actually tomorrow. Thanks for watching.
What's your opinion on the STOCK folding INWARDS, not OUTWARDS ? To me, it is a VERY PROBLEMATIC proposition as the stock gets tangled with uniform, equipment, etc. and the shooter needs to open some room between its body in order to deploy it. FN-FAL deploys outwards...
@@renatosureal I don’t have ausecase in which that matters too much since I’m not a professional in that sense, but the beauty of the system being modular jeans that you can indeed get a stock that collapses inward like an MP5 but you have to buy that stock, or outwards to the right by just flipping the folding mechanics around.
I'm not sure of the legality, and don't take this as advice, but I assume you are not allowed to have a folding stock, so I would try to find a 1913 straight/non-folding knuckle to replace the folding mechs that it comes with. Then you can put the minimalist stock on it. But I really don't know the answer to this or who might offer it. Maybe JMAC customs makes a fixed adapter that you can bolt the Sig stock to?
How come AR's platform has not been able to ABBOLISH this FORWARD ASSIST button once and for all ?! It is the only rifle which has it ... Is it possible to get RID OF IT ??
Sub’d! Thank you very much for your videos! Learned so much from them! By the way, I have an opportunity of grabbing an LWRC SPR or a MCX Spear LT. Any thoughts to which one you would pick?
Thanks for the sub! As far as which one? LWRC is generally higher quality, but if you want something that is different and not just another AR, get the SIG. I have LWRC also and it’s been great.
Okay got it! Just in a dilema since the price and condition of both are similar. Im planning on using it for 3 gun/ multigun. Cant go wrong with either one?
@@shootloadrepeat quick question, i was trying to do a function check of the spear lower with the upper removed. The safety on the semi postion and the trigger wasnt pulling. Is that normal since the upper is off?
In this video it's just the standard Sig stock that comes with the rifle versions. I'm now running JMAC customs wire stocks and skeletonized bars interchangeably.
I found a Sig suppressor for my MCX Spear LT and it is currently in jail! When I had called Sig, they didn’t have any in stock so I’m grateful that I found one.
Yeah me too. 7.62 but it will suffice. It’s a compact one and titanium so not very quiet we’ll see how it does when it comes out of jail.
Thank you!
Thank you for watching!
Can’t go wrong with an mcx. Curious if your gonna do some more of the long range shooting videos.
Yes i have some long range videos planned.
I got the big brother and want this one too
Yeah I hear you. I want the big one too but I want it in either 6.8x51 or 6.5 CM
Sub’d. Going to pick mine up after the cali 10-day wait. Learned so much from your videos!
Nice set up
Thanks!
Lol brought to you by crippling debt. I felt that 😂
I've had to cut back a ton. As long as bills are paid, roof over head, and food in belly, right?
If you want to remove the flash hider I have seen a few guys say they soaked it in hot water which I guess loosen the rock set stuff they put on it.
Just filed paperwork on a Sig SLH 7.62 compact Ti can. I may leave it on after all. I figure I'll soak in water anyway. I have a 9L heated ultrasonic I can stick the barrel into and then put this in a barrel vise to spin it off if I get antsy waiting a year for approval to come in.
I filed for one also about a month ago as I found only one place with one in stock so I snatched. Now its the waiting game….lol
Its the Sig SLH 7.62
For me to remove the flash hide I put the tip of the barrel in boiling hot water and held it there for about 5-10 minutes. It was still VERY difficult to twist off I almost ended up breaking my desk with the vise lol. I wish Sig wouldn’t put rock set on all the flash hiders. But anyway really nice video thanks for checking mine out.
Military does use the Rattler, and I'm sure they use the 5.56 in some units. I know SAS and other elite groups have used the LT.
I guess there is a usecase for portability and maneuverability in close areas. The Rattler in 300AAC is probably the ultimate PDW and I am looking for parts to build an FDE one someday. I know you can get the black ones all day every day, so may have to settle for one of those.
@@shootloadrepeat yeah they use it in place of the MP5/MP5SD. Sentry gun and recon/intelligence gathering.
@shootloadrepeat PS. Ultimate PDW is 8.6 blackout now. Finally have full lethality at small sub sonic package.
Just stumbled upon your vids, couple of observations from my own experience. The button head torx screws for the forend will easily strip out if you torque them to 45 inch lbs., don't remove the flat head torx screws holding the retainer tab on the bottom of the forend, and finally, my Gisselle reaction rod does not fit the chamber on these guns. I had to ship my upper back to Sig to remove and replace the stripped torx screws on the forend and also asked them to remove the muzzle device as I run a DeadAir Sandman S. Customer service was great, they covered all shipping and turn around time was 4 days. They told me they have received bent and mangled receivers from customers who tried to remove the muzzle device without the proper tools.
Thanks for the information which is sorely needed. I have not yet tried to do anything with the muzzle device, and will look into sending to Sig for removal although I do have a dedicated barrel vice I could use to clamp down the barrel outside the receiver. Good to know on the handguard screws as well. Thanks for watching and for the useful info.
Little update. I removed the muzzle device by clamping the barrel (removed from upper and also removed the oprod to give me more room) in a dedicated barrel vice. I have bushings that enabled me to spin off the flash hider with a 3/4 socket and a few whacks with a dead blow hammer. Did not soak in water but if one doesn’t have a barrel vice, water soak is the only option.
The reason why so many strip the handguard screws is because they're NOT standard torx t15! They are Torx Plus IP15 screws. Wish Sig would note this !!
Wondering if you ever put the vertical grip farther back to help you use your light. Noticed it was way far forward
I have since made this into an SBR. The vfg is further back now by necessity.
How has the Arisaka retention clamp been treating you? My barrel on my mcx spear Lt moves a tad.
I’m in Texas…DFW area and bought that gun back in June….haven’t been to range yet because of the Dang heat.! I bought the retention piece recently but waiting until I get the gun out and shoot it first. What part of Texas are you living in?
I'm just North of Houston. Yeah I hear you about the heat. I've had 110 degree range days shortly after. It's brutal. Hope you get to shoot yours soon. Thanks for watching.
any more barrel flex issues? I have the 9” 300blk. Mine doesn’t seem to have the issue, but I’m concerned been seeing this all over the place.
I believe in my case it was mostly if not all, the handguard flexing and not the barrel, as I took it on a range trip and put over 300 rounds through it in quick succession. I stuck it in a case and when i pulled it out at home the. handguard has flexed over to one side. A boresight confirmed the barrel was not affected. I ended up installing the Arisaka zero retention clamp and it really stiffened the entire thing up. In your case the 9” barrel and shorter handguard will have a much smaller lever moment so the issue should be less apparent. Will see over time if it happens again but will confirm zero next time I’m out just in case.
@@shootloadrepeat thanks! I appreciate it
Do you also feel a looseness between the upper and lower? Especially when you pull the gun towards you in the shooting position?
No looseness here at all. Actually quite tight. These receivers come shipped with an installed Accu-Wedge which tightens up the 2 halves.
Do you think SIG will release the MCX Raptor soon?
Haven’t heard of the raptor but if it’s anything like the current rattler then I will try to get one. I’m debating on SBR’ing this one and getting the 11.5 barrel as that is more my preference. Thanks for watching
What size Torx do I nee for the handguard and barrel screws?
You probably already have your answer but it's T15@ 35in-lbs for the handguard retention screws and T27 @60in-lbs for the barrel clamp. Torx of course.
The handguard screws are NOT standard torx t15, they are Torx plus IP 15. This is why so many strip the srews! Wish Sig noted this. Not sure on the Barrel screws...but I suspect the same ??
What sling are you using?
I was using the Blue Force Gear Vickers Sling (Combat Applications Sling) This one: www.blueforcegear.com/vickers-one-sling
But I just set up and will use Edgar Sherman ESD sling here: www.weaponoutfitters.com/edgar-sherman-design-sling.html
I've been using the BFG slings for years, but I like how compact sleek the Edgar Sherman ones are. Will give them a try actually tomorrow. Thanks for watching.
Are you able to use the BUIS when you have a riser?
Yes but just barely. It's not lower thirds, more like lower 7/8ths lol
At first I thought I was watching the intro to Spaceballs
:)
Question, the part that holds the bolt catch just needs to be punched out right? Its not threaded?
I will have to check. I'll get back to you. Haven't tried to remove it yet.
What's your opinion on the STOCK folding INWARDS, not OUTWARDS ? To me, it is a VERY PROBLEMATIC proposition as the stock gets tangled with uniform, equipment, etc. and the shooter needs to open some room between its body in order to deploy it. FN-FAL deploys outwards...
@@renatosureal I don’t have ausecase in which that matters too much since I’m not a professional in that sense, but the beauty of the system being modular jeans that you can indeed get a stock that collapses inward like an MP5 but you have to buy that stock, or outwards to the right by just flipping the folding mechanics around.
Hello there, any idea how I can block the stock from folding? I live in CA and just purchased a MCX spear LT.
I'm not sure of the legality, and don't take this as advice, but I assume you are not allowed to have a folding stock, so I would try to find a 1913 straight/non-folding knuckle to replace the folding mechs that it comes with. Then you can put the minimalist stock on it. But I really don't know the answer to this or who might offer it. Maybe JMAC customs makes a fixed adapter that you can bolt the Sig stock to?
How come AR's platform has not been able to ABBOLISH this FORWARD ASSIST button once and for all ?! It is the only rifle which has it ... Is it possible to get RID OF IT ??
@@renatosureal yes it is modular and can be changed it for a flush cover that doesn’t have it. It’s there because of a military/contract requirement.
The PWS Mk1 Mod 2 rifles did away with it. Probably the best bang for your buck rifle out there right now; particularly being a piston gun.
Sub’d! Thank you very much for your videos! Learned so much from them!
By the way, I have an opportunity of grabbing an LWRC SPR or a MCX Spear LT. Any thoughts to which one you would pick?
Thanks for the sub! As far as which one? LWRC is generally higher quality, but if you want something that is different and not just another AR, get the SIG. I have LWRC also and it’s been great.
Okay got it! Just in a dilema since the price and condition of both are similar.
Im planning on using it for 3 gun/ multigun.
Cant go wrong with either one?
@@shootloadrepeat quick question, i was trying to do a function check of the spear lower with the upper removed. The safety on the semi postion and the trigger wasnt pulling. Is that normal since the upper is off?
What stock is that ?
In this video it's just the standard Sig stock that comes with the rifle versions. I'm now running JMAC customs wire stocks and skeletonized bars interchangeably.
@@shootloadrepeatcan you work on getting an updated set up video out? I just got one, it will be in on Tuesday. Looking to add some stuff to mine
Oh Mann, 50 Farbtöne sind zu viel 😢
You put your front iron sight on backwards 😅😅😅😅
I also said as much in the text callout. I corrected it as well.