How to Replace Rear Upper Control Arm 2003-2011 Honda Element
ฝัง
- เผยแพร่เมื่อ 22 ส.ค. 2024
- Buy Now!
New Control Arm Set from 1AAuto.com 1aau.to/ib/1ASF...
New Control Arm from 1AAuto.com 1aau.to/ia/1ASR...
This video shows you how to install new control arms in your 2003-2011 Honda Element. Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear. When those bushings run out, that can have a negative impact on the ride and safety of your vehicle.
This repair was done on a 2005 Honda Element EX 2.4L Sport Utility 4-Door 4WD Automatic and the process should be similar on the following vehicles:
2003 Honda Element
2004 Honda Element
2005 Honda Element
2006 Honda Element
2007 Honda Element
2008 Honda Element
2009 Honda Element
2010 Honda Element
2011 Honda Element
Tools you will need:
• Phillips Head Screwdriver 1aau.to/oa6o/1A...
• 17mm Wrench 1aau.to/oNh/1AX...
• 17mm Socket 1aau.to/oa8E/1A...
• 18mm Socket
• 19mm Socket
• 8mm Socket 1aau.to/oaQY/1A...
• Adjustable Wrench
• Needle nose pliers 1aau.to/oyJ/1AX...
• Needle nose pliers 1aau.to/oyJ/1AX...
• 1/2 Inch Impact Gun 1aau.to/ooL/1AX...
• 3/8 Inch Impact Gun
• Ratchet 1aau.to/objr/1A...
• Torque Wrench 1aau.to/oapz/1A...
• Floor Jack 1aau.to/oSz/1AX...
• Hammer
• Jack Stands 1aau.to/oMA/1AX...
• Pole Jack
• Punch
Subscribe: / @trq
Check out our playlist:
Honda Element 1st Generation 2003-2011: • Honda Element 1st Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
![[TH] 2024 PMSL SEA W1D5 | Fall | เก็บแต้มของจริง คือวันนี้](http://i.ytimg.com/vi/EciIAlCXg5k/mqdefault.jpg)
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Very good explanation and in a simple english...Slowly but sure Sir..Thanks a lot..
!!!ATTENTION!!!
The nuts on my 2006 were spot welded. I had to remove the bolts. Learner the hard way on the first one.
Is the rear strut out as this replacement is happening?
Thanks, could you guys make a video of how to replace the lower bushing?
Should this get the rear camber alignment where it should be on an 06 Honda CRV with those adjustable upper control arms?
I will look up the torque specs but I assume, since you said nothing for the back side, that both bolts are 69 foot pounds?
Wow, that rust😮
What were the symptoms requiring new upper control arms? Thanks for video very useful.
ATTENTION: WHEN PRELOADING THE SUSPENSION FOR APPLYING TORQUE BE CAREFUL NOT TO LIFT THE VEHICLE TOO MUCH, DOING SO CAN TIP THE VEHICLE OFF THE LIFT OR JACKSTANDS!!!
Super.👍🇺🇦
Is the same set for Honda crv 2007 also?
I'm free India
+kasi viswanath This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ