Love these old videos as he shows every aspect if taking these apart. Before these type videos came out most owners never took the Action Group apart. But he needed to zoom out a couple inches as a lot of parts were off camera. With these videos and a handful of new modern parts a Model 60 should last for another 70 years. I am amassing parts for rebuilding a neglected 1979 Model 60 with an adjustable creep DEP trigger and some Mcarbo springs. Back in 1966 my Boy Scout Troop had 5 Marlin Model 60's. They were VERY dirty and there was no money to send them to a gunsmith. So at 11 years old I learned to do all this. Yes I had springs and parts flying on the first two took apart. Swept the whole dining room with a magnet on a stick till I found all the parts.
Inherited a model 60 from my dad but it had a broken buffer. Watching another video but the video was incomplete to say the least. Came across this one and I was able to get the job done. Saved a trip to the gunsmith....thank you
Your videos have helped me a ton. I am disabled and have a good friend with a marlin 60 that was jamming and not cycling. After watching a couple of your videos, I did a little horse trading with him and took the rifle apart. It was nasty inside. I thoroughly cleaned and lubed it then reassembled. The bolt was cycling gritty. I realized after taking it apart again and watching your video again that the buffer was gone! The recoil spring was bent and the trigger housing was all boogered up. Ordered parts and while I waited, I polished the bolt and receiver. With new parts, it still jammed now and then. Found nicks on top of action. Just finished using honing stones and ceramics on top of action to make it silky smooth. The bolt glides now. Just have to take it to the range to verify.
I brought out my 60 a couple of days ago. I was lucky to have you do a trigger job on her a few years ago. I just wanted to say that, if I didn't properly thank you at the time, this is the best trigger I have on any of my .22's. It is now definitely on a par of the $300 trigger group I had from Kidd on my 10/22. Thank you, again, so much for harnessing the Model 60.
Alright, I would like to extend my absolute and sincere Thank you to you good sir. I took in a marlin model 60 in my shop for repair. I'm fairly new to gun smithing. My gun smith told me not to work on marlin 60's because they have way too many moving parts but I didn't listen. I went to replace a spring and the whole thing flew apart. three of the "e" clips were missing to begin with. I didn't realize that. soooo.... there it sat for a week, in pieces, guy calling everyday asking about his gun. I finally came across your video and I got it back together!!! I truly thank you. My only other option was going to be to buy him another gun. Thank you thank you thank you
Thanks Arrowdodger for your experience and expertise!!! My grandpa passed away recently and he’d always told me he wanted to get a KAT trigger and have you work on his mod 60 from ‘93 (I believe)....he was terrible with tech so how he knew about you I can’t say lol. But shortly afterwards he had a long battle ahead of him... The project never happened. Now I have it and by that time the ‘KAT’ apparently died as well. I really want a quality trigger but there isn’t 1 to be had. If at anytime you would be interested...the reward would match my appreciation to make it what he always wanted.
I just completed this entire procedure based on your video. i know nothing of guns, but successfully did the work. thank you for a very detailed and informative video.
Great instructional video, You inspired me to upgrade my whole action. The Marlin 60 are great guns I don't know how many thousands of rounds I've shot through mine but that came to a halt when everything wore out. Luckily parts are easy to get.
I had to change a broken buffer block I'd noticed during cleaning, and I'd never done this kind of thing before. Following your vid, I took it apart and put it back together three times with no trouble at all. THANKS!!!
I did indeed sacrifice a tweeker to make the pickle fork, and it's now in my gun maintenance kit. Thanks for recommending it. My Marlin was given to me about ten years ago by a man who didn't take very good care of it. The barrel has some rust, and the front sight is broken. Is it possible for an amateur like me to change the barrel?
THANK YOU!!!! I finally worked up the nerve to tackle this job today. I had a couple missteps and noticed one E clip was missing BEFORE I took it apart. Replaced the lifter and lifter/ejector spring and got it back together. My other Glenfield 60 just needed a tweek on the ejector position. Now BOTH 60s feed better. I think the lifter & throat need a thorough cleaning or polishing next to help get the rounds up for the bolt to pick it up more consistently. It turns out both 60s like CCI mini mags and Rem Golden Bullets the best.
Awesome content! You've convinced me again, that trial and error will not work for every scenario in smithing... Thanks for posting this video, now I can repair both of the Marlins brought in this week! SUBSCRIBED!!
Thank you so much. Saved my ass and provided for a tense and educational forty-five minute struggle with the hammer spring which had previously decided to leap out of the trigger assembly for no apparent reason.
you are very welcome. You bring up an excellent point that i neglected to mention in my videos. I know what you speak of about the hammer. Normally the hammer is trapped in the action between the breech bolt or being cocked. it should never come apart like that "inside" the rifle. However, When the action is OUT of the rifle, there is no real positive, forward "stop" (breech bolt) to keep the hammer from over traveling and coming out of the hammer spring strut bridge. So inserting a paper clip or keeping it cocked , outside the receiver, is suggested. When i repair and mail out someone's action assembly, i always include a paper clip to keep the hammer from losing its spring. Thank you very much for bringing up this topic.
Great Job Bro....i have to do this job one of these days....before i do..i think i will watch your video a dozen x before i proceed with it....Great Presentation.
I have an early 2000 Stainless 60. I installed an M-Carbo spring and trigger kit and now the lifter is blocking rounds from loading from the tubular magazine. Without be able to look at my rifle, where do you think I should start?
post a video on youtube of the action assembly as removed from the receiver. post close ups and explain your questions. we can see if it is assembled correctly.
I was going to reach out to see if you would be willing to work on my action assembly. I've read your posts on RFC and watched your videos, so I know how talented you are with the Marlins. I had previously had issues with jams and the jammed rounds looking like they had been snake bit and the bullets were bent to the side slightly. I bought a trigger kit and spring kit from M*Carbo and after installing those, the problem was gone for about 10 rounds. Then, when shooting a box of 50 standard velocity ammo, I would get about 7-10 jams. Totally not acceptable. I came here to watch your disassembly video to see if there was something obvious. Well... There was. The M*Carbo kit comes with PFTE silicone grease and I stupidly followed the instructions to liberally apply some on various locations. As you can imagine, grease and dirty .22LR ammo results in a thick concoction of sticky and grit. So I completely disassembled the action with the assistance of this video, cleaned all the gunk out and lightly lubed it with thin gun oil. I just put 100 rounds through it without a problem. Slow fire and quick double taps without a problem. I understand you are taking a step back from all this, so I'll close with well wishes for the new year and sincere thanks for all you have done for the Marlin community.
thank you for this my buddy sent me a pic of his yesterday all apart saying "i dont know what happened it just fell apart" so now im going to go help him put it back together and figure out if something broke
Excellent video - you have a way, just like the nickel trick! One quick question, trying to determine if the sear goes in front or back of the last shot hold open spring when you re-assembled?
I tried to make a video of that but my camera could not focus. I tweak the leg that mates to the side-plate until it lays flat. It takes me more than one try.
I know this was posted a while ago, but my lifter is hugging/scraping the right side of the block after the spring is in place? How much of an issue is that if it still raises and lowers?
I think it would bother me too. I recall those lifters being a stamped part with some needing some TCL at the spring and cartridge contact areas. I have used a file or Dremel to sweeten the condition. So if you can figure out why it does that and then does it affect the operation Let us know. Thanks.
Yes. The spring leg that mates with the side plate is the one you want to manipulate, insert or remove. The leg that mates with the disconnector has tight bends and should not be stressed.
Thank you. All the springs I have seen appear to be the same but they do wear and get shorter over time. I have seen Replacements 1/2" longer and had no issues with them.
Do you know where I can find a trigger assembly for the model 60 Glenfield I was directed here from a bulletin board on the web any help you could give would be great
I have experienced what you are referring to by manipulating the spring and strut with needle nose pliers. I do not think it is easier because you are messing with the spring under tension. The video disassembly may be intimidating at first but after a time or 2 it gets quick and easy that gives you confidence in understanding this firearm better. I have another video similar to this that I added tips and tricks to show how to deal with the loose hammer spring in a safe controlled manner. Good question, thank you.
Since the new 3D printed buffers are softer, why not just break apart and remove the old brittle buffer, then slit the top of the mounting hole in the new buffer and push it on the cross pin? The pin holds it down into the receiver in the opposite direction of the slit, so it shouldn't go anywhere. Seems like a much easier way to install a new buffer without all the disassembly.
It needs to have the "loading block?" replaced. Instead of racking a shell into the chamber it flings it out or it jams. It's an old Marlin M99 M1 and everything I see about it always refers to the M60 and there is enough difference I am hesitant to fool with it
Lester's Shop Talk Old style Is the action assembly was held in place with screws and the buffer pin was smaller diameter. New style is the action assembly held in place with a single plastic pin and the buffer pin is larger at 1/8 perhaps.
Good but you need to slow down people watching these was needing help to learn not to show us how fast you can go so you’re good at it but please slow down.think you
Marlin has free pdf owner manuals available from their websight. It does not show what I show you but it does show basic features and safety as explained.
thank you so much for your helpful video. I'd had to have paid a gunsmith without it. every other video moves to fast, assuming I already know where everything goes.
Love these old videos as he shows every aspect if taking these apart. Before these type videos came out most owners never took the Action Group apart.
But he needed to zoom out a couple inches as a lot of parts were off camera.
With these videos and a handful of new modern parts a Model 60 should last for another 70 years. I am amassing parts for rebuilding a neglected 1979 Model 60 with an adjustable creep DEP trigger and some Mcarbo springs.
Back in 1966 my Boy Scout Troop had 5 Marlin Model 60's. They were VERY dirty and there was no money to send them to a gunsmith. So at 11 years old I learned to do all this. Yes I had springs and parts flying on the first two took apart. Swept the whole dining room with a magnet on a stick till I found all the parts.
Inherited a model 60 from my dad but it had a broken buffer. Watching another video but the video was incomplete to say the least. Came across this one and I was able to get the job done. Saved a trip to the gunsmith....thank you
Your videos have helped me a ton. I am disabled and have a good friend with a marlin 60 that was jamming and not cycling. After watching a couple of your videos, I did a little horse trading with him and took the rifle apart. It was nasty inside. I thoroughly cleaned and lubed it then reassembled. The bolt was cycling gritty. I realized after taking it apart again and watching your video again that the buffer was gone! The recoil spring was bent and the trigger housing was all boogered up. Ordered parts and while I waited, I polished the bolt and receiver. With new parts, it still jammed now and then. Found nicks on top of action. Just finished using honing stones and ceramics on top of action to make it silky smooth. The bolt glides now. Just have to take it to the range to verify.
I brought out my 60 a couple of days ago. I was lucky to have you do a trigger job on her a few years ago. I just wanted to say that, if I didn't properly thank you at the time, this is the best trigger I have on any of my .22's. It is now definitely on a par of the $300 trigger group I had from Kidd on my 10/22. Thank you, again, so much for harnessing the Model 60.
Alright, I would like to extend my absolute and sincere Thank you to you good sir. I took in a marlin model 60 in my shop for repair. I'm fairly new to gun smithing. My gun smith told me not to work on marlin 60's because they have way too many moving parts but I didn't listen. I went to replace a spring and the whole thing flew apart. three of the "e" clips were missing to begin with. I didn't realize that. soooo.... there it sat for a week, in pieces, guy calling everyday asking about his gun. I finally came across your video and I got it back together!!! I truly thank you. My only other option was going to be to buy him another gun. Thank you thank you thank you
Thanks Arrowdodger for your experience and expertise!!! My grandpa passed away recently and he’d always told me he wanted to get a KAT trigger and have you work on his mod 60 from ‘93 (I believe)....he was terrible with tech so how he knew about you I can’t say lol. But shortly afterwards he had a long battle ahead of him... The project never happened. Now I have it and by that time the ‘KAT’ apparently died as well. I really want a quality trigger but there isn’t 1 to be had. If at anytime you would be interested...the reward would match my appreciation to make it what he always wanted.
I just completed this entire procedure based on your video. i know nothing of guns, but successfully did the work.
thank you for a very detailed and informative video.
My pleasure. Did you make a tool to help with the springs?
Thank you so much for your wonderful video. Thanks to you, I fixed my Marlin. That victory clock was oh so sweet.
Great instructional video, You inspired me to upgrade my whole action. The Marlin 60 are great guns I don't know how many thousands of rounds I've shot through mine but that came to a halt when everything wore out. Luckily parts are easy to get.
I had to change a broken buffer block I'd noticed during cleaning, and I'd never done this kind of thing before. Following your vid, I took it apart and put it back together three times with no trouble at all. THANKS!!!
Good job!...Leo, did you make a "pickle fork" or what did you use?
I did indeed sacrifice a tweeker to make the pickle fork, and it's now in my gun maintenance kit. Thanks for recommending it.
My Marlin was given to me about ten years ago by a man who didn't take very good care of it. The barrel has some rust, and the front sight is broken. Is it possible for an amateur like me to change the barrel?
THANK YOU!!!!
I finally worked up the nerve to tackle this job today. I had a couple missteps and noticed one E clip was missing BEFORE I took it apart. Replaced the lifter and lifter/ejector spring and got it back together. My other Glenfield 60 just needed a tweek on the ejector position. Now BOTH 60s feed better. I think the lifter & throat need a thorough cleaning or polishing next to help get the rounds up for the bolt to pick it up more consistently. It turns out both 60s like CCI mini mags and Rem Golden Bullets the best.
Thanks for posting this video
I accidentally disassembled mine and this was how I got it back together
Outstanding video! Need to see the details & good light
great video.. I was afraid to dissassemble that.. now i see it done.. its not so bad. thx !
Awesome content! You've convinced me again, that trial and error will not work for every scenario in smithing... Thanks for posting this video, now I can repair both of the Marlins brought in this week! SUBSCRIBED!!
You are welcome Bill. As long as you are getting into a couple Marlins, look at my tips and tricks videos also for some helpful hints.
Thought my model 60 was done for, that is, until I watched this video! Thank you so much!!!
Thank you so much. Saved my ass and provided for a tense and educational forty-five minute struggle with the hammer spring which had previously decided to leap out of the trigger assembly for no apparent reason.
you are very welcome.
You bring up an excellent point that i neglected to mention in my videos. I know what you speak of about the hammer. Normally the hammer is trapped in the action between the breech bolt or being cocked. it should never come apart like that "inside" the rifle.
However, When the action is OUT of the rifle, there is no real positive, forward "stop" (breech bolt) to keep the hammer from over traveling and coming out of the hammer spring strut bridge. So inserting a paper clip or keeping it cocked , outside the receiver, is suggested.
When i repair and mail out someone's action assembly, i always include a paper clip to keep the hammer from losing its spring. Thank you very much for bringing up this topic.
incredible video, thank you for sharing your knowledge with such a clear demonstration. favorited for later
Great Job Bro....i have to do this job one of these days....before i do..i think i will watch your video a dozen x before i proceed with it....Great Presentation.
I have an early 2000 Stainless 60. I installed an M-Carbo spring and trigger kit and now the lifter is blocking rounds from loading from the tubular magazine. Without be able to look at my rifle, where do you think I should start?
post a video on youtube of the action assembly as removed from the receiver. post close ups and explain your questions. we can see if it is assembled correctly.
I was going to reach out to see if you would be willing to work on my action assembly. I've read your posts on RFC and watched your videos, so I know how talented you are with the Marlins. I had previously had issues with jams and the jammed rounds looking like they had been snake bit and the bullets were bent to the side slightly. I bought a trigger kit and spring kit from M*Carbo and after installing those, the problem was gone for about 10 rounds. Then, when shooting a box of 50 standard velocity ammo, I would get about 7-10 jams. Totally not acceptable. I came here to watch your disassembly video to see if there was something obvious. Well... There was. The M*Carbo kit comes with PFTE silicone grease and I stupidly followed the instructions to liberally apply some on various locations. As you can imagine, grease and dirty .22LR ammo results in a thick concoction of sticky and grit. So I completely disassembled the action with the assistance of this video, cleaned all the gunk out and lightly lubed it with thin gun oil. I just put 100 rounds through it without a problem. Slow fire and quick double taps without a problem. I understand you are taking a step back from all this, so I'll close with well wishes for the new year and sincere thanks for all you have done for the Marlin community.
thank you for this my buddy sent me a pic of his yesterday all apart saying "i dont know what happened it just fell apart" so now im going to go help him put it back together and figure out if something broke
Excellent video - you have a way, just like the nickel trick! One quick question, trying to determine if the sear goes in front or back of the last shot hold open spring when you re-assembled?
The next time you have a chance, will you show how to keep the disconnector spring in? Mine won't stay in.
I tried to make a video of that but my camera could not focus. I tweak the leg that mates to the side-plate until it lays flat. It takes me more than one try.
I know this was posted a while ago, but my lifter is hugging/scraping the right side of the block after the spring is in place? How much of an issue is that if it still raises and lowers?
I think it would bother me too. I recall those lifters being a stamped part with some needing some TCL at the spring and cartridge contact areas. I have used a file or Dremel to sweeten the condition. So if you can figure out why it does that and then does it affect the operation Let us know. Thanks.
Thank you Sir, very helpful tutorial!
Great videos, but I need info how how to replace the disconnector spring in the stamped version of the model 60. Can you help?
Yes. The spring leg that mates with the side plate is the one you want to manipulate, insert or remove. The leg that mates with the disconnector has tight bends and should not be stressed.
Hola.. el resorte de retroceso es la misma media para todos los marlin?
No hablo espanol.
Are all blowback marling springs the same?????
Thank you. All the springs I have seen appear to be the same but they do wear and get shorter over time. I have seen Replacements 1/2" longer and had no issues with them.
@@arrowdodgerluvsmarlins1758 thank you.
Usually your local Napa auto parts has those tiny clips in stock! (Rtrd Napa mgr.)
Olá tudo bem tava precisando de um estrato desse aí completo como faço pra comprar????
Please, the short "leg" of the lifter spring goes below of the last shot hold lever too? thanks.
Yes
@@arrowdodgerluvsmarlins1758 Thanks.
How do you get the trigger spring back on
Do you know where I can find a trigger assembly for the model 60 Glenfield I was directed here from a bulletin board on the web any help you could give would be great
DIP Products offers Marlin 60 trigger assemblies.
@@arrowdodgerluvsmarlins1758 thankyou for the quick reply.
And a very fine version! thank you sir!@@arrowdodgerluvsmarlins1758
What is the “hold open spring” called?
Hypothetically speaking, if the big spring were to become seperated from the hammer, is there a trick to set it back easily?
I have experienced what you are referring to by manipulating the spring and strut with needle nose pliers. I do not think it is easier because you are messing with the spring under tension. The video disassembly may be intimidating at first but after a time or 2 it gets quick and easy that gives you confidence in understanding this firearm better. I have another video similar to this that I added tips and tricks to show how to deal with the loose hammer spring in a safe controlled manner. Good question, thank you.
Since the new 3D printed buffers are softer, why not just break apart and remove the old brittle buffer, then slit the top of the mounting hole in the new buffer and push it on the cross pin? The pin holds it down into the receiver in the opposite direction of the slit, so it shouldn't go anywhere. Seems like a much easier way to install a new buffer without all the disassembly.
So if I wanted to assemble a trigger assembly from parts, what would the list if parts be that I would need to order?
Dr. MJOLNIR ..please see your owners manual for parts. Manuals are available at the Marlin website.
I have acquired a marlin 60 and the trigger has no movement, even when removed from gun
lash out hold open lever also dont hold bolt back either?
Larry, I have a video on replacing that. It's not difficult. Give it a go.
Do you do repairs on these for people?
Maybe, depends. What's going on?
It needs to have the "loading block?" replaced. Instead of racking a shell into the chamber it flings it out or it jams. It's an old Marlin M99 M1 and everything I see about it always refers to the M60 and there is enough difference I am hesitant to fool with it
Please see my video on feed throat replacement. It's not too difficult.
I will lok at it again, and see what happens
@@lmfinato search for: feed throat marlin 60
I need a new buffer. How do I know if this model 60 Is a new model or old model
Lester's Shop Talk
Old style Is the action assembly was held in place with screws and the buffer pin was smaller diameter. New style is the action assembly held in place with a single plastic pin and the buffer pin is larger at 1/8 perhaps.
Thank you sir for the information and the quick reply.
I can’t get the spring back over the release no matter how hard I try
Kirby, make a little "pickle fork" tool from a cheap screwdriver. I`m thinking that would help.
arrowdodger luvs marlins thanks i just got it on with a regular screwdriver but it took a while. Your videos are helpful
Arrowdodger how can i get one KAT trigger?
I retired, so no more are available. Sorry.
@@arrowdodgerluvsmarlins1758 sad to “hear” that, thank you for your answer!
Trigger wont let hammer go what do I do.
Look for disconnector issues. Make sure the disconnector spring is in position.
I'll take a look thanks.
Good but you need to slow down people watching these was needing help to learn not to show us how fast you can go so you’re good at it but please slow down.think you
why wont mine feed??
can anyone tell me how does this hold 14 rounds
The model 60's have a tube magazine under the barrel. They have varied in length depending on the year it was made. The longest ones held 17 or 18.
can I still get the kat?
yes but i am out of parts until next year. thanks !
Ok sweet when would be a good time to check back with you
??
3-4 weeks yet
lol thank u I am a new gum owner that's my first and I just could not figure it out
Marlin has free pdf owner manuals available from their websight. It does not show what I show you but it does show basic features and safety as explained.
thank you so much for your helpful video. I'd had to have paid a gunsmith without it. every other video moves to fast, assuming I already know where everything goes.
En castellano