23 on the pinion, I am putting on the 24 back on. It will run 25 on the pinion. As you see, at the beginning, the clutch was good, so I am up grading the clutch spring today with 9500 rpm spring
45 goes hard . It started out well until I had a slip on the clutch shoe holder, and it blew the crank case seal out. At the time, using 23 pinion ratio and it can pull 26 teeth on the pinion quest easy.
That Rovan 45 rips pretty good! What kind of pipe you using?? I know the rovan 45 the exhaust port is bigger than normal. Also is your rovan 45 ported? Awesome bash!
Runs an Olimate 45 exhaust. The 45 rip rips well , I have more tuning on the clutch to do as I'm putting in a 9500 rpm spring in the next days. As you see from the start, the clutch is working well, and then the clutch is starting to show that it needs more work in the spring department. Yes, it ported!!
@@robertblunden7160 Very nice job on the porting! I bought the bartolone/rovan(brovan) casereed 45 ! It runs well! Keep up the great work! I might have to try 9500 spring my self or 10k spring.
Very cool! I have a 30cc Baja. I love the big gas rc cars !
👍
I still have some clutch shoe tuning to do. I two clutch springs coming, 9 1/2 and a 10,000 rpm spring coming this week.
What springs ? You have the 8k's in there ? Nice rip. 👊
yes, it's 8000 rpm spring, putting in a 9500 spring in it the next two days, and going up on the pinion gear ratio.
What gearing ?
23 on the pinion, I am putting on the 24 back on. It will run 25 on the pinion. As you see, at the beginning, the clutch was good, so I am up grading the clutch spring today with 9500 rpm spring
Pulls damn good for a 45cc
45 goes hard . It started out well until I had a slip on the clutch shoe holder, and it blew the crank case seal out. At the time, using 23 pinion ratio and it can pull 26 teeth on the pinion quest easy.
Chique baja 🏎 🔥 💥 💨 😍😎👍🏻💪🏻
👍
That Rovan 45 rips pretty good! What kind of pipe you using?? I know the rovan 45 the exhaust port is bigger than normal. Also is your rovan 45 ported? Awesome bash!
Runs an Olimate 45 exhaust. The 45 rip rips well , I have more tuning on the clutch to do as I'm putting in a 9500 rpm spring in the next days. As you see from the start, the clutch is working well, and then the clutch is starting to show that it needs more work in the spring department. Yes, it ported!!
@@robertblunden7160 Very nice job on the porting! I bought the bartolone/rovan(brovan) casereed 45 ! It runs well! Keep up the great work! I might have to try 9500 spring my self or 10k spring.
Thanks. You have to do a video of your reed 45. Because I never seen a reed case 45 go👍
Put a bigger gear on like say 22 .. good run though 👍
It was running a 23 pinion, which i normally runs a 24 pinion.
But after I saw it run at the beginning of the video, it's needs 26 on the pinion.
@@robertblunden7160 the top end doesn't look like a 23. But ok 👍
We are talking about the pinion gear ratio
Just put out a new video to explain about the motor
👌🏽🤙🏽
👍
Why was it keep cutting off, are you running to lean ?
I ran well at the start, and then it blew the crank case seal out, and I had a clutch shoe holder slipping