Check the ohms of the sub that smoked... Since the same amp burned on that sub it's possible that when the sub smoked the coils could have shorted and made the load too low for the amp.. Just something to check before replacing the amp and it possibly happening again
I am willing to bet, the sub smoked because they're not really rated for that kind of power to begin with. Not many subs out there that can handle 5k rms constantly.
@@robcooper3171 every sundown Xv2 and above I have ever owned has taken 5k+ daily for years of pounding abuse and still playing! Hell even though I hate them the Orion HCCA are rated for 5k and my Wolfram PT-18'S are rated for 4krms with 4in PE flat wound coils good for up to 500deg F so yes there are plenty of woofers that will take 5k+ constantly and keep on keepin on just have to know HOW to do it properly because a typical 5k rms amplifier is only ever going to clamp 3k-4k during use as the impedance rises now had he had overbuilt korean amplifiers then I doubt this ever would've even happened but something about those full-bridge/full range Brazilian amps when you're purposely overpowering your woofers they tend to let out the smoke! Not saying all full bridge amps do this as B2 audio has successfully made some great amps in that class but I personally will stick with korean surfboards ie. Right now my current build is two Wolfram PT-18'S and each woofer has its own Wolfram AW-9000.1D at 1ohm yes these amps are capable of dynoing over 14k watts clean and I intend to send every bit of it into one woofer!!! Lol
@@Chris-B-Bassin hell yeah bro, I have two Dave Lieb Designs upgraded X12's with black zv5 spiders and NS coils with the SPL surrounds and they're legit the most violent little pair of 12's I've ever heard I literally only clamped 3k on the pair at 2.3ohm after rise on a single 3500.1 and the cones never even moved much at all but it broke my sunroof on my Lincoln mkx knocked it right off the track and it never opened again smh the entire vehicle flexed like crazy best it ever did was a 150.1 at 28hz in a subsonic suicide box made to play ground pounding lows! I would love to throw some real power to them in the same box and see what they can really do because I know they'd take 5k each all day long but unfortunately I own too many subs that're much beefier 15's or 18's so I never have had the chance to really mess with those 12's on any real power!
@@kevinAuman1 I was clamping 3500w on a Salt 4 at 2ohms in a Concept Enclosure box but just got a Turbulent Designs 8" BAP box and these subs are way louder and are moving a lot less like you said. Crazy. I love this new box for sure
@@CC6_Fanclub_President I would recommend using bolts for your terminals on your enclosure, or get some of the heavy duty ones that Steve meet makes which are essentially just bolts and really thick plastic.
@@ParkerTheBasshead can you do a review of the Hifonics BRW12D4? They are only $167 on Amazon and actually seem like high quality sub from hifonics. Look like the G2 subs.
That's the inductor, not the transformer on the amp. Typically they go out when there is some distortion here and there. Anyhow, great build! Greetings from PR!
Those coils are a low pass filter to remove the class d artifacts. The clipping light probably means the inductor is bad and not filtering the noise so the amp thinks it’s clipping
Those would be your output inductors(chokes). Seeing as you had an issue, with that side, with the subwoofer as well. I would ohm it that subs coils. See if they have any differences between each coil, due to heat stress. That could be what caused the issues with your amplifier in that side as well. Or the amplifier could have been the issue, which in turn caused the subwoofer to clip, and heat up. A couple of variables could have caused the amplifier, to heat the inductors up that much.
The left side sub smoked because your box isnt symmetrical, it had a lot more room to breath than the other one because your port was under it and it would move more or less more than the other one. The best and the loudest box for 2 subs is wood port in the midle from top to bottom, it will act as as a brace too so no additional bracing needed.
12:40 - yeah, that's a transformer, yes, it heats up too, so, this can cause with it a simple overheating too. Also the transformers are too far from the fans + the big caps are between the trasformers and the fans which makes worse the tansformer's cooling. In the most cases if you just replace this thansformer, the amp will work normally like before. Also 1 of my friends had similar problems with his amp more times even though he had an external fan which blowed air on the amp: always some component was toasted inside the amp which wasn't connected to the heatsink, then I realised that is because of overheating. I just made a new bottom plate for the amp without venting holes, cut a hole on it for an extra fan, I checked which direction the original fan pushes the air - it was pulling the air outwards from the amp, then I installed the extra fan in such a way that it pushes the air inwards into the amp - to make ideal air circulation -, and this solved the problem. In my opinion it is a good idea to make this on your amps too because mainly those big caps are resisting the air flow from the fans to the transformers. Ideally this extra fan should be at least as big as the original fan, or / and should push at least that much air like the original fan, and obviously also need to pay attention to not cover it when placing the amp back into the car...
I just doublechecked what I've seen on the vid, they can be also transformers - because there are existing transformers which are looking like these -, but maybe they are just inductors - if it only has 2 terminals, they are inductors, if it has more than 2 (usually 4) terminals, they are transformers. They're looking like they have just 2 terminals + also they are labelled as "L1" and "L2" - because of these things they are inductors for sure. Also I see there +2 outlets for extra 2 fans on the plate where the clip light is, so yeah, I would put there extra 2 fans for sure, so, the new bottom plate with that extra fan isn't really necessary in the way I wrote before, but anyways, I would maybe put there that extra fan - 5 fans total = ideal cooling...
@@PBasschannel Their output inductors. Just about every class D amplifier out there has them, they filter out some of the noise from the switching power supply.
It bugs be how awkward people can be at these events. Like you can't talk, you're not moving so there's nowhere to look ahead, so everyone's just stuck nodding or just staring at the sub.. Or awkwardly glancing at the camera lol. I love bass but I can't handle that lmao
Parker the big square things are the transformer what u called the transformer is the choke and they get extremely hot that amp needs that choke removed and replaced immediately or when it goes it's taking the whole output section with it it's manufacturer flaw defect better just send the amp back in if u can cause it's stuck in clip mode cause the insulation on the choke wires melted and are not having the correct amount of turns now and will drastically affect the ohm load the amp sees. Those fans need 4 fans or one big fan strait in the center directly on the chokes.
Nice. Had a sub or to burn before. It happens. Man that coil got hot. I've had taramps go into clip and pop when my voltage got down to 11.3 volts. My fault for not paying attention. Keep hitting. Now time to beef up the truck for the sound.
Was great meeting you that morning waiting for the gates to open! I knew I should have followed you to the infield, I parked out on the track and was only able to give like 6 demos 😞. Definitely had a great time and will be seeing everyone again at ruckus and chill!!!
Who's system is that at @9:29 it is a Wolfram Audio C pillar wall??? I literally have the exact same equipment and wanted to do a C-pillar but was advised against it because I was told there wouldn't be any surface for the subs to load off of smh 🤷♂️🤦♂️
Those output inductors got HELLA hot on that amp, those filter out the high switching frequency of the class D amp. My bet is the clip light is on due to it not filtering correctly anymore.
Hey parker thanks for getting a demo of the Cummins man the xv3s has gotten a lot louder now and moves a lot more air! At the 23minutes and some change! Hope to see you at rukus in November will have a 8k on it by then!!
When the coil blew it crossed the POS and negative and blew output fets prolly but that sux he was exited to try this new stuff they didn't last long at all tho
I don't know about the rest of you guys but I love the guys who give demos and smile everytime the bass hits, all day long. I hate the guys who sit in the driver's seat stoic, no smile, like, I just do this because I want to be heard. Not because you love it like Parker and the rest of the people who are there. Great video Parker, not so sure about black brick for hard demoing, more for an everyday driver.
did that guy really have speakers just laying on the back seat wired up and playing only mids or highs but man that is a first for me to see and parker love the old barn around where you live I like all the older property with woods and the old barn nice the truck looks good too other than the big pipe in the bed but it is yours and you can do what you like to it another great video
Hey Parker I was wondering how do you like your atoto head unit Im thinking about buying one but I was wondering about your opinion before I bought one
Go with the six man you know you want too... I'm building a setup right now with 4 E15 V4 D4 in an explorer and still thinking of two more as well and still may.... HUGH shout-out to you btw Parker I did the sundown yard sale because of you man and I couldn't be more thankful!!!!
I called that beast build! You never really disappoint me im a huge fan of yours parker the basshead my idol!! Watching and supporting everytime here in the philippines! 🙏🙌🔊
This is not a transformer. It's the output inductor (Choke) between amp and speaker. This is a full bridge amplifier which has two complete amplifiers in it, which do exact the same signal with a phase shift of 180 degrees (inverted). The speaker has no ground potential and is between the two amps. So the voltage on the speaker is doubled with one single rail voltage. It looks like one half of your amp died. So you have still signal on the output with the half of the voltage (quarter of the power) and mostly you even have a dc offset on the terminals, too. Check with a voltmeter, if there's DC on the speaker.
Hell yeah! Was one of the best Sundown shows yet! I loved the demo I got from you! I'll be posting it later today! Also glad you liked the Slappin Saturn! Don't feel bad about breaking stuff and smoking stuff! I smoked one of my subs to! They still playing after they cooled down. But probably should be recone. But that was after back to back Demo's! Nice meeting you again! Can't wait to see what you come up with next! @Parker the Basshead 👊😎💯💨💨💨
You killed the output choke and the clip light is on because the amp is sensing high frequency AC on the output because it's not being filtered by the choke.
Shout out to you for not using the same song while demoing! Crazy how many ppl do.🤷♂️ I got a pretty nice Mercedes-Benz I don't wanna ruin, but am fixing lil stuff all the time🤷♂️🤦♂️ just the casualty of war🤷♂️🤣
Smashing memories to cherish, loads of fun doing what you love is extremely satisfying when realizing ones dreams it's something we all want. Seems like you're living your dream. Keep inspiring us all with you're awesome projects and keeping it as simple as you make it look, keeps me for one inspired. Thanks, Keep 🔊'ing on bro 🤟
You should do a video on sound proofing showing how a little or how a lot can make a difference with pressure testing, Your bass was not enough for the fans maybe upgrade your alternator and add some batteries. All of your screws and bolts just use clear nail polish or Loctite.
When you get that loud that a car or truck falls apart. Your beyond the sound of music !! It's called ground shaking noise or in your case car shaking !!
Awesome vid, Glad that back window didnt shatter even though that would have been bad ass lol. A bit off topic but are you still making your DIY batteries? Im interested in buying a couple. Let me know either way please.
Looks very fun. Wishing i had my set up done and there. Building a tapped horn for 2 10s next weekend. Max x from dayton. For a buddy. My set-up is pretty basic 15 in a 6th order bass reflex. Nothing like what you are doing hahaha.
Huh. I would have been interested to see the output from the amp on an oscilloscope to see if it was really distorted. Having a light like that stay on is kind of a goofy failure mode
The Black Brick Built in fans might've not been enough to help cool it down or keep it from overheating, I've seen many set up's with those jet engine styled blowers to help the amps stay cool or help the fins get rid of the heat even more
Hey parker can you do a review of the Hifonics BRW12D4. They look like a G2 audio subwoofer. For only $167 on Amazon they seem like a hella good deal. They apparently had some sort of branding conflict and that's why they are so cheap, they're trying to get rid of them quick.
Check the ohms of the sub that smoked... Since the same amp burned on that sub it's possible that when the sub smoked the coils could have shorted and made the load too low for the amp.. Just something to check before replacing the amp and it possibly happening again
I am willing to bet, the sub smoked because they're not really rated for that kind of power to begin with. Not many subs out there that can handle 5k rms constantly.
@@robcooper3171 every sundown Xv2 and above I have ever owned has taken 5k+ daily for years of pounding abuse and still playing! Hell even though I hate them the Orion HCCA are rated for 5k and my Wolfram PT-18'S are rated for 4krms with 4in PE flat wound coils good for up to 500deg F so yes there are plenty of woofers that will take 5k+ constantly and keep on keepin on just have to know HOW to do it properly because a typical 5k rms amplifier is only ever going to clamp 3k-4k during use as the impedance rises now had he had overbuilt korean amplifiers then I doubt this ever would've even happened but something about those full-bridge/full range Brazilian amps when you're purposely overpowering your woofers they tend to let out the smoke! Not saying all full bridge amps do this as B2 audio has successfully made some great amps in that class but I personally will stick with korean surfboards ie. Right now my current build is two Wolfram PT-18'S and each woofer has its own Wolfram AW-9000.1D at 1ohm yes these amps are capable of dynoing over 14k watts clean and I intend to send every bit of it into one woofer!!! Lol
@@kevinAuman1 I have a Salt 6 on 2 12" Xv2s and I've yet to even see the clip light, it's loud in my hatchback 😁
@@Chris-B-Bassin hell yeah bro, I have two Dave Lieb Designs upgraded X12's with black zv5 spiders and NS coils with the SPL surrounds and they're legit the most violent little pair of 12's I've ever heard I literally only clamped 3k on the pair at 2.3ohm after rise on a single 3500.1 and the cones never even moved much at all but it broke my sunroof on my Lincoln mkx knocked it right off the track and it never opened again smh the entire vehicle flexed like crazy best it ever did was a 150.1 at 28hz in a subsonic suicide box made to play ground pounding lows! I would love to throw some real power to them in the same box and see what they can really do because I know they'd take 5k each all day long but unfortunately I own too many subs that're much beefier 15's or 18's so I never have had the chance to really mess with those 12's on any real power!
@@kevinAuman1 I was clamping 3500w on a Salt 4 at 2ohms in a Concept Enclosure box but just got a Turbulent Designs 8" BAP box and these subs are way louder and are moving a lot less like you said. Crazy. I love this new box for sure
That is an impressive build! Looking forward to seeing what is next!
Hey! I know you!
Good to see you here 👍👍
Bassheads supporting bassheads yeeyee 🤘
Thanks again DIYAudioGuy for helping me so often lol
DIY. How would you recommend connecting a direct lead sub in box? I'd like to keep them semi-easy to remove if needed. Thank You!
@@CC6_Fanclub_President I would recommend using bolts for your terminals on your enclosure, or get some of the heavy duty ones that Steve meet makes which are essentially just bolts and really thick plastic.
Very nice parker, a lot of smiles and fun. Its what its all about. Realy enjoyed the series and watching your build come to life
Thank you Chris!
@@ParkerTheBasshead can you do a review of the Hifonics BRW12D4? They are only $167 on Amazon and actually seem like high quality sub from hifonics. Look like the G2 subs.
I had to go back n paint every bolt n screw with Loc tite.. got a bottle of blue and red in the tool box for the stuff I rattle loose.
Potential fix for 3 piece rear window : camper shell and back window blow through!!
Use some Medium Strength (Blue) Loctite on those threads... Will greatly increase the chance of it backing off again
What's the song at 21:01? Almost knock Paker out his draws lol
2:40 Recommendations stop nuts or purple loctite.
That's the inductor, not the transformer on the amp. Typically they go out when there is some distortion here and there. Anyhow, great build! Greetings from PR!
Or vibration. Looked really loose
I thought it was a toroidal type transformer. Now I gotta go back and look
The transformers are yellow, in that full bridge.
They call those coils a choke.
Those coils are a low pass filter to remove the class d artifacts. The clipping light probably means the inductor is bad and not filtering the noise so the amp thinks it’s clipping
Those would be your output inductors(chokes). Seeing as you had an issue, with that side, with the subwoofer as well. I would ohm it that subs coils. See if they have any differences between each coil, due to heat stress. That could be what caused the issues with your amplifier in that side as well. Or the amplifier could have been the issue, which in turn caused the subwoofer to clip, and heat up. A couple of variables could have caused the amplifier, to heat the inductors up that much.
7:04 What you was experiencing was "power compression"
monitor your voice coil temps with a infrared thermometer
The left side sub smoked because your box isnt symmetrical, it had a lot more room to breath than the other one because your port was under it and it would move more or less more than the other one. The best and the loudest box for 2 subs is wood port in the midle from top to bottom, it will act as as a brace too so no additional bracing needed.
Started to melt the varnish on that inductor ! She was hot !
12:40 - yeah, that's a transformer, yes, it heats up too, so, this can cause with it a simple overheating too. Also the transformers are too far from the fans + the big caps are between the trasformers and the fans which makes worse the tansformer's cooling. In the most cases if you just replace this thansformer, the amp will work normally like before. Also 1 of my friends had similar problems with his amp more times even though he had an external fan which blowed air on the amp: always some component was toasted inside the amp which wasn't connected to the heatsink, then I realised that is because of overheating. I just made a new bottom plate for the amp without venting holes, cut a hole on it for an extra fan, I checked which direction the original fan pushes the air - it was pulling the air outwards from the amp, then I installed the extra fan in such a way that it pushes the air inwards into the amp - to make ideal air circulation -, and this solved the problem. In my opinion it is a good idea to make this on your amps too because mainly those big caps are resisting the air flow from the fans to the transformers. Ideally this extra fan should be at least as big as the original fan, or / and should push at least that much air like the original fan, and obviously also need to pay attention to not cover it when placing the amp back into the car...
I just doublechecked what I've seen on the vid, they can be also transformers - because there are existing transformers which are looking like these -, but maybe they are just inductors - if it only has 2 terminals, they are inductors, if it has more than 2 (usually 4) terminals, they are transformers. They're looking like they have just 2 terminals + also they are labelled as "L1" and "L2" - because of these things they are inductors for sure. Also I see there +2 outlets for extra 2 fans on the plate where the clip light is, so yeah, I would put there extra 2 fans for sure, so, the new bottom plate with that extra fan isn't really necessary in the way I wrote before, but anyways, I would maybe put there that extra fan - 5 fans total = ideal cooling...
@@PBasschannel Their output inductors. Just about every class D amplifier out there has them, they filter out some of the noise from the switching power supply.
@@BobBasshead yeah, exactly...doublechecked what I've seen - my previous answer to my comment...
It bugs be how awkward people can be at these events. Like you can't talk, you're not moving so there's nowhere to look ahead, so everyone's just stuck nodding or just staring at the sub.. Or awkwardly glancing at the camera lol. I love bass but I can't handle that lmao
Parker the big square things are the transformer what u called the transformer is the choke and they get extremely hot that amp needs that choke removed and replaced immediately or when it goes it's taking the whole output section with it it's manufacturer flaw defect better just send the amp back in if u can cause it's stuck in clip mode cause the insulation on the choke wires melted and are not having the correct amount of turns now and will drastically affect the ohm load the amp sees. Those fans need 4 fans or one big fan strait in the center directly on the chokes.
Nice. Had a sub or to burn before. It happens. Man that coil got hot. I've had taramps go into clip and pop when my voltage got down to 11.3 volts. My fault for not paying attention. Keep hitting. Now time to beef up the truck for the sound.
At 10:53 if you look behind your head, that dude's sub was throwin sparks 🔥
Was great meeting you that morning waiting for the gates to open! I knew I should have followed you to the infield, I parked out on the track and was only able to give like 6 demos 😞. Definitely had a great time and will be seeing everyone again at ruckus and chill!!!
Who's system is that at @9:29 it is a Wolfram Audio C pillar wall??? I literally have the exact same equipment and wanted to do a C-pillar but was advised against it because I was told there wouldn't be any surface for the subs to load off of smh 🤷♂️🤦♂️
22:03 Ahhh the biggest nozz in car audio, Mr. Bought Not Built himself.
I smoked my Soundqubed subwoofer the other day and it still works. It's wired in series so I know it has both coils working.
Those output inductors got HELLA hot on that amp, those filter out the high switching frequency of the class D amp. My bet is the clip light is on due to it not filtering correctly anymore.
maybe check the output signal on the amp and verify its not clipping the signal sent to the sub? just a thought about the clip light staying on
it’s a must i hit a show when the next show and where is it?
Ruckus and Chill is another big one coming up. It’s in NC
100K by end of year! Love the hair tricks with just 2 subs in a box type build.
Bassjunkie 2020 in tha house. ...
Hey parker thanks for getting a demo of the Cummins man the xv3s has gotten a lot louder now and moves a lot more air! At the 23minutes and some change! Hope to see you at rukus in November will have a 8k on it by then!!
When the coil blew it crossed the POS and negative and blew output fets prolly but that sux he was exited to try this new stuff they didn't last long at all tho
Thats Micah_Lundy parked next to you in the red dodge that thing is insane
Hey I got a solid rear window and the solid half door windows you can have if ya come get them
I don't know about the rest of you guys but I love the guys who give demos and smile everytime the bass hits, all day long. I hate the guys who sit in the driver's seat stoic, no smile, like, I just do this because I want to be heard. Not because you love it like Parker and the rest of the people who are there. Great video Parker, not so sure about black brick for hard demoing, more for an everyday driver.
did that guy really have speakers just laying on the back seat wired up and playing only mids or highs but man that is a first for me to see and parker love the old barn around where you live I like all the older property with woods and the old barn nice the truck looks good too other than the big pipe in the bed but it is yours and you can do what you like to it another great video
Haha thanks man I got rid of the bed stack and ran a proper exhaust!
I saw sundown 2022 show it was dope man ur truck was literally shaking the windows
Love the show . Thx for showing us the after affects/ damage of doing these shows that put so much stress on everything 👍🏼
Keep basin Parker😁
I am truly considering this very same build in my 08 expedition!!
Good to see you again guy,those BB audio subs were impressive
Hey Parker I was wondering how do you like your atoto head unit Im thinking about buying one but I was wondering about your opinion before I bought one
Go with the six man you know you want too... I'm building a setup right now with 4 E15 V4 D4 in an explorer and still thinking of two more as well and still may.... HUGH shout-out to you btw Parker I did the sundown yard sale because of you man and I couldn't be more thankful!!!!
6 in a truck like that probably wouldn't need window or anything else with a box for them that size
Lol he is going to be building his Sequoia next not sure if he wants to do 4 15 or 6 either way windows may need some attention sometime or another
I called that beast build! You never really disappoint me im a huge fan of yours parker the basshead my idol!! Watching and supporting everytime here in the philippines! 🙏🙌🔊
This is not a transformer. It's the output inductor (Choke) between amp and speaker. This is a full bridge amplifier which has two complete amplifiers in it, which do exact the same signal with a phase shift of 180 degrees (inverted). The speaker has no ground potential and is between the two amps. So the voltage on the speaker is doubled with one single rail voltage. It looks like one half of your amp died. So you have still signal on the output with the half of the voltage (quarter of the power) and mostly you even have a dc offset on the terminals, too. Check with a voltmeter, if there's DC on the speaker.
Parkers next build will be 12 12s lol. Those shows always made me want to go bigger and louder
Hell yeah! Was one of the best Sundown shows yet! I loved the demo I got from you! I'll be posting it later today! Also glad you liked the Slappin Saturn! Don't feel bad about breaking stuff and smoking stuff! I smoked one of my subs to! They still playing after they cooled down. But probably should be recone. But that was after back to back Demo's! Nice meeting you again! Can't wait to see what you come up with next! @Parker the Basshead 👊😎💯💨💨💨
I always go through and loctite the bolts in the door handles the mirrors shit like that
You killed the output choke and the clip light is on because the amp is sensing high frequency AC on the output because it's not being filtered by the choke.
Shout out to you for not using the same song while demoing! Crazy how many ppl do.🤷♂️ I got a pretty nice Mercedes-Benz I don't wanna ruin, but am fixing lil stuff all the time🤷♂️🤦♂️ just the casualty of war🤷♂️🤣
JPs build managed to take your hats off lol also that last one where your hat came off as well. That steering wheel was wanting to come off lol
Smashing memories to cherish, loads of fun doing what you love is extremely satisfying when realizing ones dreams it's something we all want. Seems like you're living your dream. Keep inspiring us all with you're awesome projects and keeping it as simple as you make it look, keeps me for one inspired. Thanks, Keep 🔊'ing on bro 🤟
What a blast. Damn that truck looks phenomenal!!! 🤟👍🏻
BassJunkie 2020 gang in the building!!!
Can u test the jbl tornadoes really curious to what they hold
I see you broke that 70,000+ mark for subscribers. Congrats bro !!! 😎
I would have used lock tite on the nut that came loose because might do it again, definitely should use a one piece glass in the back
I have a sundown sfb 5k that has the clip light on like that also but it doesn't work at all. Maybe I should check the transformer
Love JB weld ! I've done "not recommend" things with it and it's held 🤘
Loc-tite is a must for high vibration situations. I’m a Harley owner. I’ve got plenty of experience losing bolts lol.
Any thoughts on re-tuning the ports to 35hz give or take? Seems like the spl would be higher at higher frequency if tuned that way.
it's awesome to see your hard work pay off.
Yessir!!
@5:19 those subs are slammin hard af!
You should do a video on sound proofing showing how a little or how a lot can make a difference with pressure testing, Your bass was not enough for the fans maybe upgrade your alternator and add some batteries. All of your screws and bolts just use clear nail polish or Loctite.
I'm sorry you're going through all of this. Those things are getting down though..wow!
A Parker we need a review on the ampere audio 3.0 v4 or the encore
Parker, how do you recommend wiring direct lead subs? I'd like to make them semi-easy to remove. Thank you!
When you get that loud that a car or truck falls apart. Your beyond the sound of music !! It's called ground shaking noise or in your case car shaking !!
Man that looks like fun! I can’t wait to go to one of these shows 🤘 great job Parker and love all your videos
You will not regret it show much fun and sooo many people just like the us all ready to bass
Man as always majorly saving my life motivational.... Salute , Blessings to everyone grind and motivations....
19:47 , song name??
Vibrate-Petey pablo
@@Twiistedpyro thanks very much
you push it too much and make a lot of damage 🔊💨💥
this thing is beast 💪🏻🔥🔥🔥
Any bolt that rattles off.. I would definitely put some blue loctite on it when I put it back on.
It looks like you had fun and meet a lot of builds and that truck was slamming good job parker.
Looks good, my friend. Congrats on hitting 70k!
You should demo Rittz's song Propane if you want some bass 😮😮😮 it's fantastic
So glad I go to meet you man super dope experience 👍🏽👍🏽
Awesome vid, Glad that back window didnt shatter even though that would have been bad ass lol. A bit off topic but are you still making your DIY batteries? Im interested in buying a couple. Let me know either way please.
Looks very fun. Wishing i had my set up done and there. Building a tapped horn for 2 10s next weekend. Max x from dayton. For a buddy. My set-up is pretty basic 15 in a 6th order bass reflex. Nothing like what you are doing hahaha.
Once u go 15s it's hard going to anything that's not as equally loud or louder, but bass is bass
That smoke was most likely just the glue because they are new and I've seen this happen on other videos and in person.
Alright hear me out on a project idea. Black Brick build. Nothing but blackbrick.
Yeah they are dropping speakers soon! That would be cool
Thanks 👍 you took it,😁im sure you have new dimples from all the smiling,🥊you knocked one out😌 keep it up Legend Status awaits you👑
Dam Parker your build came out really really nice. I see that u had many people smiling. GOOD JOB MAN 👍👍
Huh. I would have been interested to see the output from the amp on an oscilloscope to see if it was really distorted. Having a light like that stay on is kind of a goofy failure mode
Do an isobaric box
You was bringing it.
Please do a comparison between the X12 V3 and AB xmaxx 12❗️❗️❗️❗️
Did you say you had a stock alternator on your truck still?
Nope! 370 Mechman
Out there doing all that without ear plugs. New channel name will be “Parker has Tinnitus”
Huh?? What?? Don’t believe me?? Oookkkaaayyy
Everyone was smiling so it musta been a great day. Good job
I need heeelp i have gzhw 30 xspl D1 and i dont know what kind of box i should make
I hate I missed the show. I live about 20 minutes away from there
Would like to see you test the Tymphany stw 350
These blackbric put some work on this truck..the lows soo damn impressive👏👏😲
The Black Brick Built in fans might've not been enough to help cool it down or keep it from overheating, I've seen many set up's with those jet engine styled blowers to help the amps stay cool or help the fins get rid of the heat even more
Does anybody put together clean balanced systems anymore?
Make a mic that can handle the spl. I'm sure there is a heap out there. Just can't hear it because the mic isn't made to take the abuse of this hobby.
What subs did the dude in the hat at 10:40 have?
Hey parker can you do a review of the Hifonics BRW12D4. They look like a G2 audio subwoofer. For only $167 on Amazon they seem like a hella good deal. They apparently had some sort of branding conflict and that's why they are so cheap, they're trying to get rid of them quick.
How did you like being tuned way lower than your usual builds?
so let me get this straight you pushed 5k rms to the brickhoise 15s thats rated at 3000? if so thats amazing
Well there is box rise so I’m not exactly sure what they were really taking hit yes each sub took a ton of power and lasted all day!
@@ParkerTheBasshead that’s amazing thanks for the reply bro
@@ParkerTheBasshead if your ever in the Fort Lauderdale area I’ll love to give you a demo
Gotta bump the cuntree in the lifted truck ❤️ it
How about a Psi Platform 5 build in the Sequoia?
Show gain or loss with wood on the back window
Good shit my dude.