All the contrary in Illinois it is mandatory to have your vehicle inspected for safety and emissions, very strict even more than Texas, an inspected vehicle will be in better shape than that, in IL that pick up would have had the registration shredded and the DMV will have taken it off the system..😂
Even fairly new vehicles if fail emissions 3 times, gets the reg scrapped right at the inspection center which is managed straight by the government, not private shops .he might had made it run but get it back on the road? It'd cost a boat load of money .
Whaaaat, so the internets experts were right and I shouldn't have had my brake disks ground but replaced em, never mind that they are still working over a year later lol.
Finally someone that doesn't over torque wheel bearings! I have serviced 100's of trailer and 2wd front axle bearings and loose is ALWAYS better than tight. Tightenn and turn to smash out new grease, loosen 1/8-1/4 turn and lock it. You'll never overheat a bearing.
And I have been "preloading" bearings for 30 years and never had a problem. - And I get full floating or oil filled axles on trucks and trailers brought to me because when I am done with them, they *DON'T* leak... One truck came from the Ford Garage that made it about 1,000 miles rear-end grease spilling everywhere...When I took it apart they were almost 5 flats loose on NEW bearings... See with used bearings you might get away with that slightly loose crap, but a new bearing that hasn't run in yet...You leave it that loose and you will not keep seals in it because its not concentric. Even Used bearings that size I put at 20-24 in.- lb preload and put the keeper on.
Hey Wes.... I really enjoy your channel. Here's a high-tech tip for your one-man brake bleed job for those times that you are alone while your lovely assistant is out getting her nails powder coated. If you are using a GoPro you can set it up to film the bleed port. Then have it broadcast via Bluetooth.... You just need the associated app on your smart phone/iPad monitor so you can watch for the bubbleless stream..... But your way works great too! I liked the tech tip you mentioned which was to loop the bleeder hose up above the level of the bleed port. I'll do that next time! Looking forward to your next job.
I had a brand new 85 86 V6 Ford Ranger manual transmission 2 wheel drive as a company truck and it seemed incredibly snappy back then... I loved that thing !! My boss had a Nissan 4X4 pickup with a 4 cylinder dual spark plug setup with manual transmission and that was literally the slowest thing I'd ever driven in my life....
@@csterett Living on an island in the Gulf of Mexico, our vehicles are nowhere near this rusty. Just poorly maintained or evidence of a lot of alcohol related accidents. XD
I don't usually comment about any videos in general, but being a lifelong Californian (for better or worse) I am amazed by the rusty dogs that people from the midwest will fix up and get running again. You guys should come to California and pick through some of the junk yards here. The frames are usually rust free and the motors are usually the only thing needing replacement. My 1990 F250 that my father bought new, still has the original paint on the frame. I wish that some of these midwesterners would come here and save some of these cars from the scrappers.
I'm 42 and absolutely love driving these older cars from when I was a kid. My current means of A to B is an 88 Toyota Camry. Paid $600 for it and have probably dumped another $1,800 into it. Replaced all the exhaust from the converter back. Put new tires on it, brakes and rotors, wheel hubs w/bearings, and both lower control arms. Then gave it an alignment. Next was a starter and radiator. Just blew the head gasket the other day, so that's getting replaced now along with the timing belt (might as well). All that'll probably run me another $800. It currently has a rear bumper held on by a coat hanger, but I don't care. I do quite well for myself and could easily buy a new car, but I love the old smell of it and not caring if it gets a ding, the simplicity of fixing and driving it, and the rock bottom insurance rates. My dad instilled some cheapskate values in me. haha. That man would repair things until they flat couldn't be repaired anymore and wouldn't be caught dead buying anything new, especially a car.
Not sure if he was joking or not. But Wes said that someone offered him 2k for it before he got it running. I don't understand because it literally has nothing left in terms of the entire floor. Is it even safe to operate on the road anymore? I'm not familiar with rules regarding totally rotted out vehicles.
…Do are part 3. Fixing up the floor boards and any other thing that needs attending. I learn from your videos. Two thumbs up. Every video you make is worth watching…
Yes, a lump of rust can be an acceptable part if the working surfaces are still mostly there. These are pretty tough little trucks and I’m sure it will be fine but I would have spent a little more quality time with that needle scaler. I suppose that may have simply reduced its lifespan but I would have felt a little better. 🙂
I used to live (and went to college) in Upstate New York. One of my roommates and I bought an old Ford Maverick for 50 bucks, did a quick tune up on it and flipped it for $250. The lady that bought it said that when her husband tried jacking it up (bumper Jack if I remember correctly) the wheels stayed on the ground while the body went up!
My two favorite mechanics on youtube. I learn so much watching either one, and when you are keeping a 20.5 year old car on the road, anything you can learn is good.
Transmission countershaft noise. Hi Wes... I've used Lucas Oil Stabilizer on several old transmissions with good results. It's only about $10 bucks a quart which would be plenty in an old farm truck tranny. I've even used it in a '78 Harley Sporster that I used to own. Turned that clunky/clanky shift into more of a silky one. Worth a try. 👍
Before I retired, I used to look forward to Saturday cuz I didn’t have to work. Now I look forward to Saturday because of your videos!! And thank you very much for acknowledging my comments! Much appreciated. Great video as always Wes!!!!
Nice trick with the home made brake bleed bottle above the Frame so air can travel up good one man system there havent seen it done that way before with bottole being above frame @Watch Wes Work
I've seen rusty vehicles but this one takes the cake and shows how much salt they dust on the wintry roads. She came out nice out of the workshop and should give good service.
I've had the brakes stick to the drum and catch the brake lines and tire on fire on a 1990 Tempo. Maybe that's what caused the fire. That is pretty much the same brake system I had in my '82 Escort. After a memorable day trying to replace them in a driving rain in the woods, where those @%*# springs kept shooting off into the woods and getting lost, I decided I would never need new brakes again. I built a habit of anticipation of stops, downshifting and coasting. My 1990 Ranger, I got 110,000 miles out of the brakes. When we finally replaced them, they still didn't really need it. It always amazes me how quickly people dismiss the old ways of doing things. We used to get 2-3 trips through the brake lathe before the rotors and drums needed to be replaced. They would outlast 2-3 sets of pads. That really makes me miss my little Rangers. They were great little trucks.
I think most of society drives their vehicle like they’re watching a damn video game. I have two electric flatbed GEM’s at work that are maxed out at 25 miles an hour. Sure as shit, after only one year I hop in the thing and the damn brake pedal is all the way to the floor. Take off the tire and look at the pads and they’re almost down to metal. This is what happens when you let millennials use equipment
Most likely the white powder is from the fire extinguisher they used to put out the fire caused by the alternator....known issue for the 2g alternator... they pointed the harness up and it fills with water , salt etc.... then one day the regulator goes full charge all the time and the fusible link is a tad to big so it glows brightly and starts a fire 🔥....and it's all over but the crying
What about those front brake hoses on those Tempos? The retainer bracket swells with corrosion and pinches the hose, and people end up chasing a mystery brake-drag condition... I used to spread those brackets with a large flat blade screwdriver, and fix that problem!
Pops had a 90 2wd, younger brother blew the engine at 180k. Older brother installed used engine from junk yard, mixed some electronics... bad move. Would idle rough until warm (closed loop), even ford engineers couldn't solve the mystery. My turn, around 400k i brought it back from the dead, installed a clutch painted the rusted out roof. Lastly, changed the plastic idler pulley surface... was worn all the way through to where the belt was running on the star pattern underneath. Totally agree on bearing tolerance. After 40 years I finally know how those funky brake pliers are used! Nice work once again. Pretty cool little truck, maybe Fritz will offer you big bucks to get it back!
I purchased a new 1988 Ford V-6, 5 speed Ranger XLT Extended cab. Drove 8 years, Still looked like new, put 80,000 miles on it, sold it for more than new purchase price. It was a good little truck. Only vehicle that I got more back than I paid for it!
I was always told that the retainers you find on front rotors (including those on that style 4x4 hub) were there to keep the rotors in place on the assembly line. Although I can see the value in retainers for those caps since they want to fall off every time you remove the wheel. For those, I always put a small rubber o-ring on one of the wheel studs which works to keep that cap in place.
"Aerosol overhaul"!! Too funny. Glad you turned the rotors. That's my preference, but it's getting harder to find someone that will do it for you. Another great video.
I miss my Ranger sometimes, it was a 1991 Ranger regular cab / long bed in raven black with red interior, 3.0L V6 / 4spd Automatic Mine was 2WD though which made for some interesting / spirited driving in Wester Pennsylvania in the winter ❄❄❄
Not trying to knit pick, but my dad used to own an auto restoration business and he was a big stickler for originality EXCEPT for brakes. He wouldn't let a car into the shop unless they knew it was leaving with modern disc brakes, lines, fittings, etc from front to back. Disc brakes didn't belong on anything that could go over 25 mph as far as he was concerned. That was even the case for my 2001 XJ Cherokee. It had rear drums when I bought it, but when I brought it to his shop to have rear shackles installed to get rid of the Jeep rear squat I got it back with a full disc brake setup from a Grand Cherokee. They still worked flawlessly when I sold it eight years later.
Thx for the trip back memory lane, Wes! Had an '87 Ranger 4x4 with the 2.9 and man 5 sod. Great little truck, even though I replaced the tranny around 117k if I recall correct. The 2.9 had plenty of power for it's size, was much better than the 3.0 Ford used in the late 90 early '00 rangers. Those Mitsubishi trans were weak. Never should have been put in a truck. Engine started blowing oil past the valves and the rear end bit the dust around 190k. That was all she wrote.
I've seen things come out of the depths of the ocean in better shape than that chassis! :) Good stuff Wes, really enjoy following your trials and tribulations.
@@Jobro_Ya_Know I’ve seen much worse my self the wheel wells and cab corners are still there and pretty much rust free so far. Hell I’ve seen them and S10’s with rust holes in the bumpers on the few that are still on the road.
Awesome video. Rusty ?? Maybe I haven't seen the body of it . It's cool though, he figured out what was wrong with it. I only see rust on the rims. Did you notice any rust on the body? I didn't, looks very straight. Rusty pick-up. He didn't show too much of the body , front, back sides inside the bed of the truck. 👍👍
I've been working in a shop for 13 years, we don't have a brake lathe, but we have taken rotors to the guy across the street and he had machined them for us. I just when back to school to get certified, and learned that Ford dealers will not warranty rotors unless they have been machined first to try and get rid of shakes. We got to use some old AMMCO machines, apparently I still know how to use them, even though I haven't used one since 2005 when I was in grade 12.
Ford ignition module uses a 4.5 mm socket. Ask me how impressed I was when I could only buy one off the Snap On truck, unless I wanted a 3.5 hour drive. This was pre Amazon, heck pre mail order for any tools in Western Canada.
When you rapped on the wheel cylinder (at 11 min. in) I flinched because I felt a spec of rust hit my eye. Damn flys. almost 3/4 inch of axle hub outside of the studs, sure would give a mechanic more room to work on shoes if that space were 1/4 inch less. Damn engineers. If I had a brake lathe I would use it too on any vehicle over 8 to 10 years old. right now I am redoing a brake job on a 46 CJ2A. last time was in late 60's. Not worn out delaminated. Damn JC Whitney parts. Damn impact makes so much moise one can't hear the "click"
I second this! Mines blows cold but the compressor cycles like mad. Ill be making an appointment soon to see if a AC shop can confirm the refrigerant that's currently in the system before I order an adjustable pressure switch and have them recharge the system if needed.
Haha letting her loose a little! 👍 I have a handful of 7mm sockets I turned down for the ignition module bolts. Seems like I can never locate the special one and end up making a new one. Funky design!
Great job! That turned out to be a nice truck. Love me some Rangers! I'd kill to have a brake lathe like that.. You're so lucky. If I had one, I'd definitely turn my own drums and rotors, just like we all used to. I hate the throw away/replace mentality nowadays. If a parts not too far gone, I don't see the problem with rejuvenating what you got and getting your money's worth out of it! 👍 Cheers
Hey Wes you doing the rear brakes brought back memories some involved a lot of 4 letter words. Any way as a substitute cap retainer use a couple of thin o rings they work great. Keep up the videos and don't let the negative comments bother you. There just jealous of your talent.
Thank you for these two videos Frank, really enjoyed them. I got a 1988 Ranger from a place close to Dallas about a month ago but didn't have the chance to lay my hands on it until yesterday. Pulled the spark plugs out and they all looked great. Fluids were good as well. I replaced the starter and as I cracked it just to see if the engine would turn at all, the old lady sprung to life!! I could not believe it!! Everything checked out fine so I put it in gear and took it for a short spin. Totally love it. Forgot to say that being a Texas truck, there is no rust at all even after 33 years. The reason of my surprise is that the former owner told me that he had some electrical problems and there were some burnt wires in the forward right area, just behind the overflow tank. I simply pulled all the wires apart and isolated them; I have not fixed anything yet. Anyway, as you can imagine I am very encouraged now about fixing everything that needs work and invest more time and money on this beautiful little.
I’d love to see a part three with the tranny repair and a part four for the floors. I wonder how much shipping would cost to get a floor shipped up from the south.
I once had a Ford Ranger, 2wd with the pinto 4cyl engine. Once I replaced the auto choke with a manual choke it ran fairly well. And despite weekly trips to the car wash the underside looked like this after four years of Western New York winters! I traded it in on a 1990 Mazda which was very similar to the Ranger, and drove it for ten years with none of the trouble the Ford gave me. Considering that Ford and Mazda were co-operating on these trucks it's surprising how different in the long run they were.
Living in the southwest, you and I have very different definitions of what "good" looks like. Everything is so evenly oxidized I couldn't even tell where one part ends and the other begins. I know this may be surprising in your area, but metal is not supposed to make crunching sounds when you touch it
I have a 1983 ranger, I also live in a salt ridden area. My brakes work just fine! It really helps if you don't just do the bare minimum of cleaning up all the loose rust. Clean as much as you can with a wire wheel and brush and it's a much better job in the end! I've owned my truck since 1997, done more than a few brake jobs on it since it's got over 400,000 miles on it. Lots of other stuff to. Lol
*Quietly crosses Illinois off the list of places to look for a used vehicle*
All the contrary in Illinois it is mandatory to have your vehicle inspected for safety and emissions, very strict even more than Texas, an inspected vehicle will be in better shape than that, in IL that pick up would have had the registration shredded and the DMV will have taken it off the system..😂
Even fairly new vehicles if fail emissions 3 times, gets the reg scrapped right at the inspection center which is managed straight by the government, not private shops .he might had made it run but get it back on the road? It'd cost a boat load of money .
Chicago as a whole, same with Michigan.
@@johncarter1205only in the chicago area though. everywhere else in illinois it’s not required
as a Californian I won't ever complain about rust again. You're making miracles on that thing Wes
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
“Structural floor mats.” I about spit coffee on my iPad laughing. Keep making these videos friend
That tickled my funny bone too.
Where else do you think he achieved his stated "weight reduction"?
Flintstones floorboards, even better
I means I can eat more for breakfast...
@@MarshallBF yabba dabba do!
I thought it was nice to see someone turn rotors and drums again!
Finally finished fixing frank fritzs fairly functional ford
Fractionally fabulous
Pretty sure there is room for another f word or two in there.
@@phrozenwun frobably
Whaaaat, so the internets experts were right and I shouldn't have had my brake disks ground but replaced em, never mind that they are still working over a year later lol.
Opens with trying a donut in the grass and a burnout in the driveway. I was half expecting a vice grip garage crossover.
Juvenile. Sophmoric. I love it.
I was waiting for the steering to go out and him to plow in to the corn field.
I was waiting for the back end to separate. I can’t believe people drive things like this on public roads. Thankfully I don’t live there.
That would be a treat seeing Wes & Derik from VGG do a video together, especially if they got the kids & wives involved
Please god no. VGG is terrible
C'mon Wes we need a part 3 of the Fritz Ford...even if it's later
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
“Arerosol overhaul” - I’m swiping’ that one!
…and Wes, I don’t why anybody would argue with you.
Talking is loads easier than doing
Finally someone that doesn't over torque wheel bearings! I have serviced 100's of trailer and 2wd front axle bearings and loose is ALWAYS better than tight. Tightenn and turn to smash out new grease, loosen 1/8-1/4 turn and lock it. You'll never overheat a bearing.
whoa cool to see you were here too!
And I have been "preloading" bearings for 30 years and never had a problem. - And I get full floating or oil filled axles on trucks and trailers brought to me because when I am done with them, they *DON'T* leak... One truck came from the Ford Garage that made it about 1,000 miles rear-end grease spilling everywhere...When I took it apart they were almost 5 flats loose on NEW bearings... See with used bearings you might get away with that slightly loose crap, but a new bearing that hasn't run in yet...You leave it that loose and you will not keep seals in it because its not concentric. Even Used bearings that size I put at 20-24 in.- lb preload and put the keeper on.
If you were able to put this truck into a big vat of evapo-rust the truck would just disappear!
Enzo why do you have a racist symbol as your pics might as well say KKK
@@bryanmcentee9321 Since when is the NASA logo racist?
@@CountryRock2k1 always has nasa was formed by captured nazi war criminals to get us to so called space before the russians do alittle research
@@bryanmcentee9321 lol, sure thing bud.
@@firesurfer we never won ww2 pls wake up the nazis won came here we still got guys in our military cops and judges are all the KKK brotherhood
Hey Wes....
I really enjoy your channel.
Here's a high-tech tip for your one-man brake bleed job for those times that you are alone while your lovely assistant is out getting her nails powder coated.
If you are using a GoPro you can set it up to film the bleed port. Then have it broadcast via Bluetooth.... You just need the associated app on your smart phone/iPad monitor so you can watch for the bubbleless stream.....
But your way works great too!
I liked the tech tip you mentioned which was to loop the bleeder hose up above the level of the bleed port.
I'll do that next time!
Looking forward to your next job.
"Flintstones floorboards". Classic Wes.
I had a brand new 85 86 V6 Ford Ranger manual transmission 2 wheel drive as a company truck and it seemed incredibly snappy back then...
I loved that thing !!
My boss had a Nissan 4X4 pickup with a 4 cylinder dual spark plug setup with manual transmission and that was literally the slowest thing I'd ever driven in my life....
I’m from the no salt south, still amazed by how bad vehicles are from salt areas! Much respect for those repairing the evils of corrosion…
If you go too far south you get into salt. Not on the roads for de-icing, but if you live close to the ocean the salt air creeps into everything,
@@csterett Living on an island in the Gulf of Mexico, our vehicles are nowhere near this rusty. Just poorly maintained or evidence of a lot of alcohol related accidents. XD
I don't usually comment about any videos in general, but being a lifelong Californian (for better or worse) I am amazed by the rusty dogs that people from the midwest will fix up and get running again. You guys should come to California and pick through some of the junk yards here. The frames are usually rust free and the motors are usually the only thing needing replacement. My 1990 F250 that my father bought new, still has the original paint on the frame. I wish that some of these midwesterners would come here and save some of these cars from the scrappers.
When prising-off a circlip, hang a rag over it. That stops it attaining orbital velocity when it jumps off.
ya know 9 times outta 10 I do and it doesn't fly, but that 10th time I don't it becomes a rocket lol
Where's the fun in that?
Orbital velocity? Let's hope that the International Space Station isn't in jeopardy!
Andrew Main. You are 100% correct. In My Humble Opinion. One would think that could be shortened. IMHO. Hey! I like that! What? NM. Andrew. YES!! :-)
Wish I had of used that trick when taking off a circlip from a piston on one of my videos, heard it land and approx area but it's gone...
I'm 42 and absolutely love driving these older cars from when I was a kid. My current means of A to B is an 88 Toyota Camry. Paid $600 for it and have probably dumped another $1,800 into it. Replaced all the exhaust from the converter back. Put new tires on it, brakes and rotors, wheel hubs w/bearings, and both lower control arms. Then gave it an alignment. Next was a starter and radiator. Just blew the head gasket the other day, so that's getting replaced now along with the timing belt (might as well). All that'll probably run me another $800. It currently has a rear bumper held on by a coat hanger, but I don't care. I do quite well for myself and could easily buy a new car, but I love the old smell of it and not caring if it gets a ding, the simplicity of fixing and driving it, and the rock bottom insurance rates. My dad instilled some cheapskate values in me. haha. That man would repair things until they flat couldn't be repaired anymore and wouldn't be caught dead buying anything new, especially a car.
"Aerosol overhaul", lol! Hadn't heard that one before. I always learn something new on my Saturday mornings with Wes...
RIP Franky. Loved the show when you were art of it, never watched another episode once they removed you.
I'm so glad I live down south. I'd lose my mind with all that rust.
Not sure if he was joking or not. But Wes said that someone offered him 2k for it before he got it running. I don't understand because it literally has nothing left in terms of the entire floor. Is it even safe to operate on the road anymore? I'm not familiar with rules regarding totally rotted out vehicles.
@@giggiddy good winter beater. Prerusted. Better than ruining a $50,000 truck in the salt
I was thinking the same thing. The anti-ruster in me wanted to clean it all off.
@@DeweyCheatumNHoweLLC Prerusted. Lol. Cheers!
@@giggiddy He is a little bit less concerned with the floor but the frame ???
…Do are part 3. Fixing up the floor boards and any other thing that needs attending. I learn from your videos. Two thumbs up. Every video you make is worth watching…
Living in southern USA, that underside is terrifying....
Yes. He said, "I cleaned this up!" And pointed to a rusted assembly. Hahahaha
Yep. Down South, we'd send that one to the crusher. But, Up North, they go by a different standard.
Yes, a lump of rust can be an acceptable part if the working surfaces are still mostly there. These are pretty tough little trucks and I’m sure it will be fine but I would have spent a little more quality time with that needle scaler. I suppose that may have simply reduced its lifespan but I would have felt a little better. 🙂
I used to live (and went to college) in Upstate New York. One of my roommates and I bought an old Ford Maverick for 50 bucks, did a quick tune up on it and flipped it for $250. The lady that bought it said that when her husband tried jacking it up (bumper Jack if I remember correctly) the wheels stayed on the ground while the body went up!
That’s not even bad for up here
Freaking genius with the air hammer on the brake drum hopefully I’ll remember that next time I need to do that
I like the way the rims turned out.
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
You used the brake lathe you restored! I'm so happy!
Finally, in the Thumbnail/beauty shot, he pulled the fog light forward. I almost died.
You can sell it back to Frank when you're done!!! LOL!!!! Thanks! You're exactly correct and the easiest way to replace those rear guides
The patina is strong with this car…, very strong.
That is one of the best comments I have seen in a long while 😂👍
@@mctobbsi You don't think he means the " Force", do you?
It's amazing just how removing the rust and repainting the wheels makes a whole vehicle look so much better
Eric O would be proud of ya
My two favorite mechanics on youtube. I learn so much watching either one, and when you are keeping a 20.5 year old car on the road, anything you can learn is good.
I doubt he could stop whining enuff to appreciate anything
Transmission countershaft noise.
Hi Wes...
I've used Lucas Oil Stabilizer on several old transmissions with good results. It's only about $10 bucks a quart which would be plenty in an old farm truck tranny. I've even used it in a '78 Harley Sporster that I used to own. Turned that clunky/clanky shift into more of a silky one.
Worth a try. 👍
Wes, you're a stand up comedian with mechanic tendencies...another fine video Sir
Love those crusty vehicles. Thanks for bending the right fog light back into place. Not sure if it works but it was driving me crazy 😜
I thought that I was the only one who noticed that fog light! Funny how it was the only thing I could see!
Before I retired, I used to look forward to Saturday cuz I didn’t have to work. Now I look forward to Saturday because of your videos!! And thank you very much for acknowledging my comments! Much appreciated. Great video as always Wes!!!!
Nice trick with the home made brake bleed bottle above the Frame so air can travel up good one man system there havent seen it done that way before with bottole being above frame @Watch Wes Work
I'm Greased Scotsman and I approve of the copious amounts of grease used in this video.
Oh my that's way too much...perfect!🤣
Good on ye laddie! I hail from Greenock myself.
Because you know what they say, "There’s nary an animal alive who can outrun a greased Scotsman." Groundskeeper Willie
I've seen rusty vehicles but this one takes the cake and shows how much salt they dust on the wintry roads. She came out nice out of the workshop and should give good service.
I've had the brakes stick to the drum and catch the brake lines and tire on fire on a 1990 Tempo. Maybe that's what caused the fire. That is pretty much the same brake system I had in my '82 Escort. After a memorable day trying to replace them in a driving rain in the woods, where those @%*# springs kept shooting off into the woods and getting lost, I decided I would never need new brakes again. I built a habit of anticipation of stops, downshifting and coasting. My 1990 Ranger, I got 110,000 miles out of the brakes. When we finally replaced them, they still didn't really need it. It always amazes me how quickly people dismiss the old ways of doing things. We used to get 2-3 trips through the brake lathe before the rotors and drums needed to be replaced. They would outlast 2-3 sets of pads. That really makes me miss my little Rangers. They were great little trucks.
I think most of society drives their vehicle like they’re watching a damn video game. I have two electric flatbed GEM’s at work that are maxed out at 25 miles an hour. Sure as shit, after only one year I hop in the thing and the damn brake pedal is all the way to the floor. Take off the tire and look at the pads and they’re almost down to metal. This is what happens when you let millennials use equipment
Most likely the white powder is from the fire extinguisher they used to put out the fire caused by the alternator....known issue for the 2g alternator... they pointed the harness up and it fills with water , salt etc.... then one day the regulator goes full charge all the time and the fusible link is a tad to big so it glows brightly and starts a fire 🔥....and it's all over but the crying
What about those front brake hoses on those Tempos? The retainer bracket swells with corrosion and pinches the hose, and people end up chasing a mystery brake-drag condition... I used to spread those brackets with a large flat blade screwdriver, and fix that problem!
I agree the white residue is A fire Extinguisher for sure @Watch Wes Work
Watching Wes on a Saturday has the same feeling as waking up early on Saturday morning to watch cartoons (when that was a thing).
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
Pops had a 90 2wd, younger brother blew the engine at 180k. Older brother installed used engine from junk yard, mixed some electronics... bad move. Would idle rough until warm (closed loop), even ford engineers couldn't solve the mystery. My turn, around 400k i brought it back from the dead, installed a clutch painted the rusted out roof. Lastly, changed the plastic idler pulley surface... was worn all the way through to where the belt was running on the star pattern underneath. Totally agree on bearing tolerance. After 40 years I finally know how those funky brake pliers are used! Nice work once again. Pretty cool little truck, maybe Fritz will offer you big bucks to get it back!
Wes: You wanna go for a ride, Pup?
Pup: You better frickin' believe I do!
Pup says "Dad, why is this truck so small?? I can jump in the red one no problem..."
Yeah he awkwardly climbs up through the floor well. Hahahaha
Pup says: chauffeur ! please open the passenger door for me so i can jump up in a more graceful way !
Eric O would be proud of you - showing all of that good ol Illinois rust!
"the inevitable estate sale" lol
I purchased a new 1988 Ford V-6, 5 speed Ranger XLT Extended cab. Drove 8 years, Still looked like new, put 80,000 miles on it, sold it for more than new purchase price. It was a good little truck. Only vehicle that I got more back than I paid for it!
It is such a pleasure to watch you at your craft. Thanks for posting good content. Could watch it half the day.
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
"Running out of easy things to do"
still has that annoying beep lol
well it's not that hard of a job, since most of the parts are rusted to the bone, it's more a find-the-parts job. ^^
I was always told that the retainers you find on front rotors (including those on that style 4x4 hub) were there to keep the rotors in place on the assembly line. Although I can see the value in retainers for those caps since they want to fall off every time you remove the wheel. For those, I always put a small rubber o-ring on one of the wheel studs which works to keep that cap in place.
At one time, they also used aluminium Phillip's head screws. Didnt work well
@@DeweyCheatumNHoweLLC Yeah, Honda did that a lot. I drilled out many of those.
@@rb3425 I wonder when engineers will realize that aluminium and steel aren't always the best of friends
@@DeweyCheatumNHoweLLC Probably never.
Fyi, there known as Quick Speed Locking Washers Push On Speed Clips
"Aerosol overhaul"!! Too funny. Glad you turned the rotors. That's my preference, but it's getting harder to find someone that will do it for you. Another great video.
Good grief, I thought the UK was bad for salt induced trauma but that is savage!!!
Love the little trucks and rebuilt my 94 in the driveway while in college
We always called it the “Krylon Rebuild”
I miss my Ranger sometimes, it was a 1991 Ranger regular cab / long bed in raven black with red interior, 3.0L V6 / 4spd Automatic
Mine was 2WD though which made for some interesting / spirited driving in Wester Pennsylvania in the winter ❄❄❄
Nice job on those rims, Wes!😉
The truck has some nice new shoes! 👟👟
New brakes and tires! Now it's ready to hit the town! 🏙
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
Wheels looks way better live the look of the grey against the black 4x4 lockers @Watch Wes Work
Yes, a part 3 please!
Man,I am IMPRESSED with the paint job on the wheels!
Looking forward to transmission repair.
I am a Ranger lover. had three of them. the 98 had 215 thousand miles when I sold it. :-)
I like the custom brake bottle hook made out of brake line. I'm going to steal your idea and bend one up for my self bleeder contraption. Thanks!
Nice editing on the tire change/wheel cleanup.
Finally someone noticed. Took forever to set that up!
I didnt know you had a Deuce and a Half. I'm currently restoring mine. You should do a video on it!
Man, I love those old 80s Ford box trucks. That’s what a truck should look like to me. Congrats on the new ride!
A part 3 would on the transmission would make an interesting video for sure 😀
Not trying to knit pick, but my dad used to own an auto restoration business and he was a big stickler for originality EXCEPT for brakes. He wouldn't let a car into the shop unless they knew it was leaving with modern disc brakes, lines, fittings, etc from front to back. Disc brakes didn't belong on anything that could go over 25 mph as far as he was concerned. That was even the case for my 2001 XJ Cherokee. It had rear drums when I bought it, but when I brought it to his shop to have rear shackles installed to get rid of the Jeep rear squat I got it back with a full disc brake setup from a Grand Cherokee. They still worked flawlessly when I sold it eight years later.
The amount of krust on your rust belt vechiles just baffles me I live in the desert i rarely ever seen anything like that
Thx for the trip back memory lane, Wes! Had an '87 Ranger 4x4 with the 2.9 and man 5 sod. Great little truck, even though I replaced the tranny around 117k if I recall correct. The 2.9 had plenty of power for it's size, was much better than the 3.0 Ford used in the late 90 early '00 rangers. Those Mitsubishi trans were weak. Never should have been put in a truck. Engine started blowing oil past the valves and the rear end bit the dust around 190k. That was all she wrote.
I've seen things come out of the depths of the ocean in better shape than that chassis! :) Good stuff Wes, really enjoy following your trials and tribulations.
She is rusty and crusty, but a decent truck.
Thank god you fixed that fog light! Was driving me crazy!
Wow that truck is rusty as hell 😅 makes for fun content though 👌
Yes sir. It’s so much fun!
@@WatchWesWork Tetanus shot every 3 days.
Minimal rust. For my area lol
@@Jobro_Ya_Know I’ve seen much worse my self the wheel wells and cab corners are still there and pretty much rust free so far. Hell I’ve seen them and S10’s with rust holes in the bumpers on the few that are still on the road.
Awesome video. Rusty ?? Maybe I haven't seen the body of it . It's cool though, he figured out what was wrong with it. I only see rust on the rims. Did you notice any rust on the body? I didn't, looks very straight. Rusty pick-up. He didn't show too much of the body , front, back sides inside the bed of the truck. 👍👍
I've been working in a shop for 13 years, we don't have a brake lathe, but we have taken rotors to the guy across the street and he had machined them for us. I just when back to school to get certified, and learned that Ford dealers will not warranty rotors unless they have been machined first to try and get rid of shakes. We got to use some old AMMCO machines, apparently I still know how to use them, even though I haven't used one since 2005 when I was in grade 12.
Ford ignition module uses a 4.5 mm socket. Ask me how impressed I was when I could only buy one off the Snap On truck, unless I wanted a 3.5 hour drive. This was pre Amazon, heck pre mail order for any tools in Western Canada.
When you rapped on the wheel cylinder (at 11 min. in) I flinched because I felt a spec of rust hit my eye. Damn flys. almost 3/4 inch of axle hub outside of the studs, sure would give a mechanic more room to work on shoes if that space were 1/4 inch less. Damn engineers. If I had a brake lathe I would use it too on any vehicle over 8 to 10 years old. right now I am redoing a brake job on a 46 CJ2A. last time was in late 60's. Not worn out delaminated. Damn JC Whitney parts. Damn impact makes so much moise one can't hear the "click"
Would love to see a video of doing the r134 conv on the ac to see if it will still work
I second this! Mines blows cold but the compressor cycles like mad. Ill be making an appointment soon to see if a AC shop can confirm the refrigerant that's currently in the system before I order an adjustable pressure switch and have them recharge the system if needed.
The caliper wedges came out pretty easy must of been newer items on them calipers @Watch Wes Work
Those rear brakes were looking like the Antikythera mechanism.
I predict this will be an under-rated coment but I'm applauding you.
Except the Antikythera mechanism is less corroded!
lol
Classy comment!
I admit, I had to look it up. Highly accurate
Haha letting her loose a little! 👍 I have a handful of 7mm sockets I turned down for the ignition module bolts. Seems like I can never locate the special one and end up making a new one. Funky design!
Great job! That turned out to be a nice truck. Love me some Rangers! I'd kill to have a brake lathe like that.. You're so lucky. If I had one, I'd definitely turn my own drums and rotors, just like we all used to. I hate the throw away/replace mentality nowadays. If a parts not too far gone, I don't see the problem with rejuvenating what you got and getting your money's worth out of it! 👍 Cheers
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
@@Fit4C WTH does Jesus have to do with Ford Rangers? If you're religious, that's fine, but take your spammy bullshit somewhere else, bro. 👌
Hey Wes you doing the rear brakes brought back memories some involved a lot of 4 letter words.
Any way as a substitute cap retainer use a couple of thin o rings they work great.
Keep up the videos and don't let the negative comments bother you. There just jealous of your talent.
it's in better condition than my '86 Ranger... I called it "The Blown Ranger".
never mind, that one has a lot more flavor than mine did.
no matter what you do this truck WILL ALWAYS BE ON THE FRITZ
I would guess that it was brake fluid that caught fire when it hit a hot rotor.
Looks like pup gives it the paw of approval. The floor pans you can get from LMC trucks. Nice truck.
"Flintstones floor mats", that was funny.
Is this going to be your 'local commuter'? Or the assistant's backup?
Nice old truck. Even rusty 80’s parts hold up better than today’s new parts.
I was waiting for him to fly in the garage and realize oh crap no brakes.
I was too. That would have been a great sound effect. Crash bang boom, tinkle
Thank you for these two videos Frank, really enjoyed them.
I got a 1988 Ranger from a place close to Dallas about a month ago but didn't have the chance to lay my hands on it until yesterday. Pulled the spark plugs out and they all looked great. Fluids were good as well. I replaced the starter and as I cracked it just to see if the engine would turn at all, the old lady sprung to life!! I could not believe it!! Everything checked out fine so I put it in gear and took it for a short spin. Totally love it. Forgot to say that being a Texas truck, there is no rust at all even after 33 years.
The reason of my surprise is that the former owner told me that he had some electrical problems and there were some burnt wires in the forward right area, just behind the overflow tank. I simply pulled all the wires apart and isolated them; I have not fixed anything yet. Anyway, as you can imagine I am very encouraged now about fixing everything that needs work and invest more time and money on this beautiful little.
I’d love to see a part three with the tranny repair and a part four for the floors. I wonder how much shipping would cost to get a floor shipped up from the south.
Jesus loves you alot trust in His death 4 salvation and be saved from eternal hell
I once had a Ford Ranger, 2wd with the pinto 4cyl engine. Once I replaced the auto choke with a manual choke it ran fairly well. And despite weekly trips to the car wash the underside looked like this after four years of Western New York winters! I traded it in on a 1990 Mazda which was very similar to the Ranger, and drove it for ten years with none of the trouble the Ford gave me. Considering that Ford and Mazda were co-operating on these trucks it's surprising how different in the long run they were.
Living in the southwest, you and I have very different definitions of what "good" looks like. Everything is so evenly oxidized I couldn't even tell where one part ends and the other begins. I know this may be surprising in your area, but metal is not supposed to make crunching sounds when you touch it
Nice shots of the Turbo Air Tractor !
33:50 Ford should have never stopped using the 300. Hasn't made a good six cylinder since discontinuing that legend.
I’d never thought to put anti sieze around the brake line where it sits in the nut! Neat trick!
Yeah, bearings are happier a bit loose than too tight.
I have a 1983 ranger, I also live in a salt ridden area. My brakes work just fine! It really helps if you don't just do the bare minimum of cleaning up all the loose rust. Clean as much as you can with a wire wheel and brush and it's a much better job in the end! I've owned my truck since 1997, done more than a few brake jobs on it since it's got over 400,000 miles on it. Lots of other stuff to. Lol
Hope to see a part 3 Wes! Will she be for sale?!
Great little truck for picking up parts and stuff..... excellent work.
"Aerosol overhaul"......I'm going to try and use that the next time I see my wife getting ready to do her hair in the morning. Wish me luck!
......that was the last time we ever heard from Dave.
@@QCJSiteB Cobra, a posted full face photo of Dave, after he pulls this on his old lady, should be mandatory.
“The inevitable estate sale”. Your humor bro leaves me in stitches!! And your delivery is genius!!