That looks 🔥🔥🔥. I just put a teraflex 3inch suspension lift on my 06. Rock sliders ,rock crawler rear bumper and tire carrier. I’m wanted to up grade from 33s to 35s. I just wasn’t sure how close the 35 would be to the fender well. But you have plenty! Im itching to pull the trigger on 35s. Then My next step is alloy axles and change the gears.
I ended taking it off.. but Its just terrible placement. I had 3 fans (all derale) go out within a year. And then I hit it on a rock/bent the bracket... which was the final straw
You'll have to check out my other videos on my channel. I did one showing a little more detail on that back deck. I used bolts to fasten it to the tub rails so it wouldn't slide or move. I've Been using it for many years and haven't had any issues at all 😁
@@TrevorNelson402 thanks. I am considering relocation... now to rethink. As i will go with a different fuel tank. By measurements... an older ford might fit. 24 gal
@@skylinemusik1 I don't even know where to start. Fiberglass is horrible quality. Body line doesn't match to fenders at ALL.. Huge gap. Fiberglass has already cracked a few places, when I got the hood it was completely flat on the back side where it is supposed to how about an 1.5 inches to match the cowl so we had to cut the support and completely reform the back of the hood so I would even bolt to the Jeep. There was chunks missing along the edges, etc etc etc. We had WAY too many hours into body work in just the hood. And it still looks awful! The vent hole was half ass covered with some chicken wire. The whole hood warps and has a big curl going into the vent
Ive had nothing but headaches with it since the day I bought it. Most of them have to do with the cooler mounting location, the cooling lines leaking, and the fan seizing up
Trevor Nelson Wow sorry to hear that. I was planning on getting one too. Well I guess a B&M in grill is the way to go. Thanks for the response. Best of luck. Nice LJ btw. Mine is still stock but I plan on using yours as inspiration. Thanks again.
![[UNCUT] ลูกหมี-ลิลลี่ เหงียน เปิดใจฟาด ปู มัณฑนา I คนดังนั่งเคลียร์ I 15 ก.ค.67](http://i.ytimg.com/vi/FKQ60Y7bJ6s/mqdefault.jpg)
Great color and awesome build, I think color matched fenders and sliders look awesome 👍🏻
Wow! That’s a beautiful LJ! I would love to add an LJ to the family.
Nice rig. Unlimited LJ guys are awesome.
Damn!!! You and your buddies sure put a lot of hard work into your Jeep. Very nice.
Beautiful LJ.
Love the new paint!
Thank you!
I have a 04 LJ and need to do the Rubicon swap.... right now it's just a Rubicant sigh...
That looks 🔥🔥🔥. I just put a teraflex 3inch suspension lift on my 06. Rock sliders ,rock crawler rear bumper and tire carrier. I’m wanted to up grade from 33s to 35s. I just wasn’t sure how close the 35 would be to the fender well. But you have plenty! Im itching to pull the trigger on 35s. Then My next step is alloy axles and change the gears.
nice work and color!!!
Very nice rig
Nice lj 👌🤘🏼
Thank you!
How you register the jeep ? Color change and all . ?
It was still registered as khaki. And if there was any questions I could show them the firewall because I didn't do the firewall
Why does the transmission cooler suck? Just bought a Jeep with the same one
I ended taking it off.. but Its just terrible placement. I had 3 fans (all derale) go out within a year. And then I hit it on a rock/bent the bracket... which was the final straw
How did you build that 3 part back deck section? How did you get it from sliding around, coming apart, or falling out of place?
You'll have to check out my other videos on my channel. I did one showing a little more detail on that back deck.
I used bolts to fasten it to the tub rails so it wouldn't slide or move.
I've Been using it for many years and haven't had any issues at all 😁
Have you made a video on how you made your custom tonneau cover in the back?
I have not. But I could when it gets a little nicer outside I'll pull it out and go over it in detail
Just made the video for you
On the exhaust...
Have you ever checked the tire pressure after a 2 hr run? Whether un city or on hwy.
Does it cause overheat?.
I have actually. Normally runs 1 psi more on the trail and 2 psi more on the road
@@TrevorNelson402 thanks. I am considering relocation... now to rethink.
As i will go with a different fuel tank.
By measurements... an older ford might fit. 24 gal
Got the stock engine or did you do a engine swap?
Yes sir, stock motor. Currently has 65k miles
Sliders?
Did you mention the gearing?
I’m just curious what it is
Now I have Yukon 5.13s with 37in Yokohama x-mts, wrapped around some raceline beadlocks
Trevor Nelson love it
Is that AEV highline hood or Duraflex?
Duraflex. Would not recommend
@@TrevorNelson402 why? Theyre selling me one for $200 brand new out the box
@@skylinemusik1 I don't even know where to start. Fiberglass is horrible quality. Body line doesn't match to fenders at ALL.. Huge gap. Fiberglass has already cracked a few places, when I got the hood it was completely flat on the back side where it is supposed to how about an 1.5 inches to match the cowl so we had to cut the support and completely reform the back of the hood so I would even bolt to the Jeep. There was chunks missing along the edges, etc etc etc. We had WAY too many hours into body work in just the hood. And it still looks awful! The vent hole was half ass covered with some chicken wire. The whole hood warps and has a big curl going into the vent
@@TrevorNelson402 oh wow thanks for the info, your jeep is a beauty. How much did that paint cost you?
@@skylinemusik1 paint by itself? Or the whole project?
Why do you not recommend the Derale trans cooler?
Ive had nothing but headaches with it since the day I bought it. Most of them have to do with the cooler mounting location, the cooling lines leaking, and the fan seizing up
Trevor Nelson Wow sorry to hear that. I was planning on getting one too. Well I guess a B&M in grill is the way to go. Thanks for the response. Best of luck. Nice LJ btw. Mine is still stock but I plan on using yours as inspiration. Thanks again.