When I lived in Japan I loved running the lil Subaru Pleo in the mountains because it was absolutely screaming and felt awesome without actually going deathly fast. Tons of fun, especially because it was so light.
@@jackkrupka3024 The last thing a beat needs is more weight and tiny farts of horsepower. These cars are meant for cornering, the best he can do is is drop some weight.
Someone pointed out on the last video that the lifts could be a safety hazard the way they are installed. I hope you saw that comment. Just a reminder to check it out! Don’t want anything bad to happen!
@@KartsAgainstHumanityThe other guy was mentioning that the concrete isn’t deep enough or the anchors aren’t in far enough. The funny part is gingium wanted to have a lift installed in his very first shop. The installers said no because the concrete was way to thin, I haven’t seen him use a installer since
Im going to post this comment a few times in the hopes that you see this. Do not read these comments as hate comments, These are people who enjoy your channel and want you to be safe. Please prioritize safety first. You can upload videos with non-lift projects while you sort this out. I have pasted 3 comments down below from professional lift installers on the subject: From @Marc11M Hey Caleb I install lifts for a living, if I was inspecting those lifts they would immediately fail because of the anchoring. I'm not as familiar with bendpak but every 2 post I've installed comes with 5-1/2 anchors which looks to be what these did come with. Most lifts want minimum 4-1/4 inches of 3000psi concrete with minimum 3-1/4 anchor embedment, as well as staying around 3-1/2 inches from cracks, seams in the floor, relief cuts, edges of the concrete, old anchors etc. which you can't see some of those issues with the epoxy already on the floor. Those anchors are pulled up way too far so either you don't have enough concrete or the concrete there is low psi or cracked/weak. I would guess you have maybe 1-2 inches of embedment on some anchors especially the ones near the drain, also since you cut off the extra length of the anchor that would also be an immediate fail due to that alone. With the little amount of room to move the lifts around in your shop I would seriously recommend you to remove the lifts and get new concrete pads poured. I do not want to see you get hurt or killed from those lifts failing please take my recommendation for your safety From @deanandrejevic1946 install, maintain and do insurance inspections on garage equipment in the UK and funnily enough used to fit Bendpak ramps and this 100% my thoughts. The bolts pulling up is extremely concerning. The cutting of the bolts is an instant condemn. Please please please get some concrete pads. I don't know if the specs in the US is different but 1m squared and 500mm deep is what we would recommend, but it will also say in the manual minimum concrete specs. It may seem overkill and a ballache but it's better than a lift falling. I've seen it happen and it isnt pretty. I see a lot of these videos and the fact Bendpak don't send professional fitters out when they ship the lifts is appalling. From @JessopRyan I fit lifts too, in the U.K. so the rules will be different. I agree those bolts pulling though aren’t good. We use Hilti bolts, I went to a training day about bolts and they are very confident even on expansion joints…. We don’t do it but they say you can. Safety First! You don't want to learn this lesson the hard way. Love ya, stay safe Gingium.
As a 3 cylinder owner (a 998cc not 600) who's exhaust rusted out effectively deleting the muffler I can atest to it sounding like a tractor at idle bit I couldn't help but like it a bit... It sounded so fast and like strong, then around the corner came a city econobox... Anyway, I like how this sounds
I’ve watched near to every video of yours since Donut reccomended you in the shoutout video. I have to say that I enjoy your videos the most from all the car channels I watch. From Rob Dahm, Drivetribe to Donut and Tavarish I can relate to yours the most even tho I don’t have the founds and motivation to play with cars as you. I think it comes to the “human” aspect of your videos. You are showing mistakes, you make silly jokes I can see that you are authentic in your work and that’s priceless. Thank you for all the hours of entertainment, all the smiles you’ve put on your and our faces and all the fails you made. I’m excited to watch your jurney. All the best from Czechia
@@robinl.7948 indeed, my goal is to make the fastest time attack kei car, or an F20C beat, already used a turbo hayabusa swapped cappu, that wasn't enough but it was at like 450-500 on e85, but the 4 rotor with a turbo according to the dude who's helping me build it is upwards of 1350 to the rear wheels in a car, including the cage + engine, + frame reinforments probably about 18-1900 pounds, instead of 1587 :)
@@robinl.7948 yeah, it's gonna have a custom 3d printed widebody kit made from thermal/heat resistant plastics, and extra wide wheels/tires (like 245s or more) and I'm thinking pirelli p-zeros, michelin pilot sport 2s, or the nitro nt series, but I prefer those as a drift setups, leaning towards pirelli
@@officiallilsideshow It would be an incredible feat to get that to function! 😃 And I'd love to see it! Nankang AR-1 275/35 R15 is probably one of the best rubber choises for such a build. I've myself been fantasising about a kei car with a Honda Goldwing 1800 dct (for reverse) engine 😁 It's a rather wide engine though, so I'm not sure what it would fit in.
Your welds here are absolutely beautoful dude. Found you when you had the miata before it was boosted. What a long way you've come. These videos inspire me to learn how to weld as well. Thanks for making great content
You should drop a Cbr600rr motor in that thing. Around 120hp would be a good jump from the original motor. I'd bet anything it would be a very easy install.. my first bike in the early 2000s was a 02 cbr600f4i. I put a D&D on that thing. Sounded great.
$50 used large flatbed scanner and a flat ruler for scale. Pretty perfect for scanning flat surfaces to adapt to CNC. A cheap tv/monitor screen protector can be used to prevent metal parts from scratching the glass with metal parts. 50% of the time a photo does the job but it skews flat surfaces, so prevent wasted metal and time with a scanner. Only takes 2 min longer than taking a photo.
If I’m being honest I wasn’t too much of a fan of the idea of him changing the exhaust setup because I didn’t know how much it would change the sound. But, my fucking god. I could sit here for hours listening to that shit bro lol. Fucking mind blown. Good shit Gingium.
I have a Honda V45 running thru 1" black steel pipe, 2 into 1 into a "collector", to an amazon CAT then a stock single vf750 muffler powering a 1995 mitsu minitruck. fun stuff
My friend, it's so amazing to see you converting cars into super cars! Tbh, I'm in a whole different work field and I have to admit that I'm jealous of your skills! I really loved the video of the Volvo! Thank you for sharing! Gr from the Netherlands!!
havent watched a vid since the rally miata / bus times. man has your recording and editing gotten insanely good like man that slow dolly pan across timelapse is amazing
Epic job on the exhaust! Sounds Amazing! Side note: A Boilermaker once showed me you can draw a simple single "V" over the join for clocking your pipes.
I love this car and your work. Awesome man. A small car like that with a 3-cylinder or even a 4-cylinder cross plane from Yamaha would be absolutely sick.
If you end up wanting it louder you can drill the rivets. The cap will come off the end. Pull some of the packing out and put new rivets in. I’ve also cut them down shorter and it sounds great on a bike
I think the one longer header tube helped avoid some of the raspy "Honda" sound you might have gotten otherwise. Gives it some tone. Overall I think you got a pretty cool sound out of it! A small resonator might actually make it even better, but you could also change mufflers if you ever want a different tone. Good stuff.
Interesting project. Gotta say though, you might wanna keep a very close eye on EGT's once you fit the spray kit and start tuning. Mild steel flange on stainless pipe is a really bad idea in high temp applications. Tends to crack around the HAZ after a few heat cycles.
I've done many a motorcycle end can conversions to get better sound quality and flow and it's a case of drill all the rivers out at the furthest end of the muffler remove all the wadding/packing and simply rivets back together and hey presto job done
Caleb this video quality and editing style is amazing and I am so proud to see how amazing it has gotten over the years. Your hard work is shown through your constant drive for fabrication and innovation. That said, THIS IS MY NEW FAVORITE EXHAUST NOISE😂
new to your channel, bubbled up through my feed! I guess the algorithms work - you seem to miss calculation of resonance ... will plumb your other vids thanks for your honest craftsmanship, Montaigne with a MIG
@_Gingium_ that is the main downside, but it just means youll have to get yourself a nice shop upgrade in the aspect of some larger argon tanks specifically for backpurging
Can't lie. Sounds hella good. I'm a Datsun guy. Have been for years. My impression from dudes that have raced Datsuns, and built their motors, headers aren't always better. In fact many argue that factory exhaust manifolds flow better. Just saying. I dig this little car. Hope to see a supercharger again. Tired of seeing EVERYONE turbo something. ❤
It is kinda wild that all this work is done, not including boosting it yet, just to still make less power than a new 600cc motor. Swap would be way cooler and probably more cost effective
when doing the header flange, you should of taken into consideration the thickness of the material of the runners. add that to the size of the exhaust ports.
I remember my mate spending a fortune on a D+D exhaust for his YZF750 back in the 90’s, they were hard to get in the UK at the time of if I remember rightly
I have a kei truck with the same engine. Its my daily and it straight piped. Honda rice stuff soon ill cut the front springs and take out a leaf in the rear and slam it on 14 inch wheels 😂
sound good, but the point is of making equal length is to make it better flow and make the gases exit in order and faster (as you said in the beginning)
Exhaust: going crazy
Caleb’s face: pure excitement
The scenery in the background: not moving
LOL
When I lived in Japan I loved running the lil Subaru Pleo in the mountains because it was absolutely screaming and felt awesome without actually going deathly fast. Tons of fun, especially because it was so light.
Some of the best cars are like this.
Okey that’s sick!!! My boy talented af.
Fr though! He is definitely putting nitrous on it😂
Jimmy!!
Spoon + Gingium collab? 🤔
Need to get the beat going
@@jackkrupka3024 The last thing a beat needs is more weight and tiny farts of horsepower. These cars are meant for cornering, the best he can do is is drop some weight.
The fact that it’s so slow just makes it more awesome! So many smiles and no speeding tickets 👍🏻
I never seen 49 HP make some one so happy. Nice build.
Spotto the chopped fingers flag. nicely done!
Been a fan for years! You guys are a huge inspiration 🤘
Someone pointed out on the last video that the lifts could be a safety hazard the way they are installed. I hope you saw that comment. Just a reminder to check it out! Don’t want anything bad to happen!
He likes to learn the hard way 😮
How are they unsafe?
@@KartsAgainstHumanity im no expert, but check the top comment on the last video, they explained it pretty good :)
He commonly does not care for safety, and does many things as cheap as possible so it’ll probably never change.
@@KartsAgainstHumanityThe other guy was mentioning that the concrete isn’t deep enough or the anchors aren’t in far enough. The funny part is gingium wanted to have a lift installed in his very first shop. The installers said no because the concrete was way to thin, I haven’t seen him use a installer since
Im going to post this comment a few times in the hopes that you see this.
Do not read these comments as hate comments, These are people who enjoy your channel and want you to be safe. Please prioritize safety first. You can upload videos with non-lift projects while you sort this out. I have pasted 3 comments down below from professional lift installers on the subject:
From @Marc11M
Hey Caleb I install lifts for a living, if I was inspecting those lifts they would immediately fail because of the anchoring. I'm not as familiar with bendpak but every 2 post I've installed comes with 5-1/2 anchors which looks to be what these did come with. Most lifts want minimum 4-1/4 inches of 3000psi concrete with minimum 3-1/4 anchor embedment, as well as staying around 3-1/2 inches from cracks, seams in the floor, relief cuts, edges of the concrete, old anchors etc. which you can't see some of those issues with the epoxy already on the floor. Those anchors are pulled up way too far so either you don't have enough concrete or the concrete there is low psi or cracked/weak. I would guess you have maybe 1-2 inches of embedment on some anchors especially the ones near the drain, also since you cut off the extra length of the anchor that would also be an immediate fail due to that alone. With the little amount of room to move the lifts around in your shop I would seriously recommend you to remove the lifts and get new concrete pads poured. I do not want to see you get hurt or killed from those lifts failing please take my recommendation for your safety
From @deanandrejevic1946
install, maintain and do insurance inspections on garage equipment in the UK and funnily enough used to fit Bendpak ramps and this 100% my thoughts. The bolts pulling up is extremely concerning. The cutting of the bolts is an instant condemn. Please please please get some concrete pads. I don't know if the specs in the US is different but 1m squared and 500mm deep is what we would recommend, but it will also say in the manual minimum concrete specs. It may seem overkill and a ballache but it's better than a lift falling. I've seen it happen and it isnt pretty.
I see a lot of these videos and the fact Bendpak don't send professional fitters out when they ship the lifts is appalling.
From @JessopRyan
I fit lifts too, in the U.K. so the rules will be different. I agree those bolts pulling though aren’t good. We use Hilti bolts, I went to a training day about bolts and they are very confident even on expansion joints…. We don’t do it but they say you can.
Safety First! You don't want to learn this lesson the hard way. Love ya, stay safe Gingium.
up
up
up
Up
Yup
Man see man build exhaust. Man happy. 😃
😃
Uggg ugggg ugggg lol😂😂😂😂
Man agrug nug
it sounds amazing, and it isn't really droney or annoying at cruizing revs, also the manifold is beautiful
I appreciate it!
it sounds exactly like a mt-09 im in love
Sounds sporty and throaty perfect exhaust for that little Kei car!
I thought it kinda sounded like a Honda 4cyl
just how i like my women
@@anonymous5072it is a Honda so it sounds like a Honda
I 100% agree!
@@anonymous5072 sounds nowhere like a 4cyl. You can hear the 3 cyl tones which are more similar to a 6-cylinder.
As a 3 cylinder owner (a 998cc not 600) who's exhaust rusted out effectively deleting the muffler I can atest to it sounding like a tractor at idle bit I couldn't help but like it a bit...
It sounded so fast and like strong, then around the corner came a city econobox...
Anyway, I like how this sounds
Haha yeah, the way the Beat sounds with the combination of how slow it is is the funniest part.
@@_Gingium_ reminds me of riding in my little brother's 2.2 ecotec 😂
exactly like my old daewoo matiz 0.8 from 2002
I’ve watched near to every video of yours since Donut reccomended you in the shoutout video. I have to say that I enjoy your videos the most from all the car channels I watch. From Rob Dahm, Drivetribe to Donut and Tavarish I can relate to yours the most even tho I don’t have the founds and motivation to play with cars as you. I think it comes to the “human” aspect of your videos. You are showing mistakes, you make silly jokes I can see that you are authentic in your work and that’s priceless. Thank you for all the hours of entertainment, all the smiles you’ve put on your and our faces and all the fails you made. I’m excited to watch your jurney. All the best from Czechia
Thank you so much for those kind words! Comments like these really help me stay motivated.
@@_Gingium_ exhuast sound would also not be the best in my concept car
The ABC kei cars are the best, as an AZ-1 owner planning a 4 rotor build for track use
Sorry did I just read that you want to put a 4-rotor in an Autozam AZ1?
@@robinl.7948 indeed, my goal is to make the fastest time attack kei car, or an F20C beat, already used a turbo hayabusa swapped cappu, that wasn't enough but it was at like 450-500 on e85, but the 4 rotor with a turbo according to the dude who's helping me build it is upwards of 1350 to the rear wheels in a car, including the cage + engine, + frame reinforments probably about 18-1900 pounds, instead of 1587 :)
@@officiallilsideshow jesus christ, that's going to need some crazy sticky rubber
@@robinl.7948 yeah, it's gonna have a custom 3d printed widebody kit made from thermal/heat resistant plastics, and extra wide wheels/tires (like 245s or more) and I'm thinking pirelli p-zeros, michelin pilot sport 2s, or the nitro nt series, but I prefer those as a drift setups, leaning towards pirelli
@@officiallilsideshow It would be an incredible feat to get that to function! 😃 And I'd love to see it!
Nankang AR-1 275/35 R15 is probably one of the best rubber choises for such a build.
I've myself been fantasising about a kei car with a Honda Goldwing 1800 dct (for reverse) engine 😁 It's a rather wide engine though, so I'm not sure what it would fit in.
sounds exactly like a triumph triple 675. what a bliss
Your welds here are absolutely beautoful dude. Found you when you had the miata before it was boosted. What a long way you've come. These videos inspire me to learn how to weld as well. Thanks for making great content
You should drop a Cbr600rr motor in that thing. Around 120hp would be a good jump from the original motor. I'd bet anything it would be a very easy install.. my first bike in the early 2000s was a 02 cbr600f4i. I put a D&D on that thing. Sounded great.
$50 used large flatbed scanner and a flat ruler for scale. Pretty perfect for scanning flat surfaces to adapt to CNC. A cheap tv/monitor screen protector can be used to prevent metal parts from scratching the glass with metal parts. 50% of the time a photo does the job but it skews flat surfaces, so prevent wasted metal and time with a scanner. Only takes 2 min longer than taking a photo.
If I’m being honest I wasn’t too much of a fan of the idea of him changing the exhaust setup because I didn’t know how much it would change the sound. But, my fucking god. I could sit here for hours listening to that shit bro lol. Fucking mind blown. Good shit Gingium.
Haha thats good to hear. I was a bit worried I'd ruin it too, but it turned out great.
this thing sounds amazing, good shit man
I have a Honda V45 running thru 1" black steel pipe, 2 into 1 into a "collector", to an amazon CAT then a stock single vf750 muffler powering a 1995 mitsu minitruck. fun stuff
My friend, it's so amazing to see you converting cars into super cars! Tbh, I'm in a whole different work field and I have to admit that I'm jealous of your skills! I really loved the video of the Volvo! Thank you for sharing! Gr from the Netherlands!!
That looks amazing for your first full header/exhaust build man!
Thank you!
havent watched a vid since the rally miata / bus times.
man has your recording and editing gotten insanely good
like man that slow dolly pan across timelapse is amazing
The joy on your face is priceless, cracking video as always 👌
Epic job on the exhaust! Sounds Amazing! Side note: A Boilermaker once showed me you can draw a simple single "V" over the join for clocking your pipes.
She sounds GREAT! Perfect exhaust for the mini-NSX 👌
I love this car and your work. Awesome man. A small car like that with a 3-cylinder or even a 4-cylinder cross plane from Yamaha would be absolutely sick.
Sounds great !!...I'd be driving it like I stole it.all the time 😂...awesome job!!!😎👍
3:04 OKAY CALEB I SEE YOU ON THAT NEW DYLAN SITTS EP. This shit been on repeat nonstop 😂😂
This video is so funny to me cuz I was a bike mechanic my whole life and years ago I put a D&D can on my Nissan 300zx and it sounded sick!
Created a 2/3 unequal length header! Sounds sick!
It sounds exactly like a 206 Dino Ferrari, which has always been lauded as being one of the best sounding cars ever made.
Love the vid, love the build, love the edits of cutting the piping with hands, love the drives at the end, instant smile, need to buy one for myself 😂
Bro the look on your face… it’s obvious that this is damn near the most fun you’ve ever had… definitely the most fun with less than 60hp.
That sound is SICK..on point perfection!!!!👊👌 Would be fun to see you do a 0-62mph how fast it is cuse it is not slow.
I love it! It sounds so fast for how slow it is! Pure silliness ! 😂 10/10
If you end up wanting it louder you can drill the rivets. The cap will come off the end. Pull some of the packing out and put new rivets in. I’ve also cut them down shorter and it sounds great on a bike
one punch man - cool car, sweet sound, awesome video
You killed it with the exhaust dude🎉 sounds amazing!!!!
Honestly that sounds SOOOOOOOO good, reminds me of proper vintage cars, like british classics. Really sick.
Love the internet coming round to Kei cars and Kei Trucks this last year or so.
Such cool little things.
Love the cutting/karate chop transitions. Always great stuff Caleb
Looks good, quiet when cruising, popping when "playing", and loud/sporty at full throttle... Sounds pretty optimal in my opinion 👍
I think the one longer header tube helped avoid some of the raspy "Honda" sound you might have gotten otherwise. Gives it some tone. Overall I think you got a pretty cool sound out of it! A small resonator might actually make it even better, but you could also change mufflers if you ever want a different tone. Good stuff.
That car sounds amazing. Great work 👍
The flyby killed me 😂😂😂😂 so slow but sounds like you were hauling
that sounds awesome. you mentioned a supercharger and now I can't stop thinking about a tiny centrifugal supercharger just spooling away 😂
22:51 This was the best part 😂 it sounds amazing but man, it looked so slow compared to your other builds.
Loving this build series!
Yeah the fly-by footage almost looked slowed down lol.
That’s the coolest sounding Kei Car Ever 😂😂😂
I had d&d race exhaust on my 2013 thruxton 900! Bike got stolen a couple years ago 😭 loved that thing
Interesting project.
Gotta say though, you might wanna keep a very close eye on EGT's once you fit the spray kit and start tuning. Mild steel flange on stainless pipe is a really bad idea in high temp applications. Tends to crack around the HAZ after a few heat cycles.
The open header sounded like every vq motor with an exhaust. Lol
Good job with the exhaust
I've done many a motorcycle end can conversions to get better sound quality and flow and it's a case of drill all the rivers out at the furthest end of the muffler remove all the wadding/packing and simply rivets back together and hey presto job done
Sounds way more refined than I would have thought!
How to sound faster then you actually are. It sounds great well done.
Sounds so good. Reminds me of Durango 95
I had a D&D exhaust on a Suzuki 750 years ago. I like it. 👍🏾
That's a long time ago Yoda. 😅
Caleb this video quality and editing style is amazing and I am so proud to see how amazing it has gotten over the years. Your hard work is shown through your constant drive for fabrication and innovation. That said, THIS IS MY NEW FAVORITE EXHAUST NOISE😂
new to your channel, bubbled up through my feed! I guess the algorithms work - you seem to miss calculation of resonance ... will plumb your other vids thanks for your honest craftsmanship, Montaigne with a MIG
sounds like your revs red limit just before it goes on pipe!
Yes! You finally snagged a Backpurge kit! Your exhausts and headers are gunna be SO much cleaner now brother
Yeah I love it! It does chew through gas though...
@_Gingium_ that is the main downside, but it just means youll have to get yourself a nice shop upgrade in the aspect of some larger argon tanks specifically for backpurging
I kinda want you to leave this little car stock on power but it is yours at the end of the day lol… sick content btw.
Ive said it 100 times. From not knowing how to install a steering wheel to doing this. Youve come a long way sir 🫡
Thank you thank you
Can't lie. Sounds hella good. I'm a Datsun guy. Have been for years. My impression from dudes that have raced Datsuns, and built their motors, headers aren't always better. In fact many argue that factory exhaust manifolds flow better. Just saying. I dig this little car. Hope to see a supercharger again. Tired of seeing EVERYONE turbo something. ❤
New subscriber just come across this channel a couple of hours ago and have been binge watching his content.Ive got to say im proper impressed.💯💯🔥🔥🔥😁😁
Damn... D&D fTW! That thing sounds amazing! I've got a D&D on my BUELL XB12STT and it also is amazing!
Nice to a see a return to s nore cinematic style video. Please make more videos in that style!
I didn't even know this car existed but I want one now. It's ashame they didn't sell them in the US.
It is kinda wild that all this work is done, not including boosting it yet, just to still make less power than a new 600cc motor. Swap would be way cooler and probably more cost effective
It reminds me of a J series with a nice exhaust note! Great job on the exhaust!
This is a pretty interesting channel. Thanks for this.
Sounds great but should’ve copped the YOSHIMURA muffler 😂
Great job dude.👊
The engine obviously loves the new breathing room.. Can't wait to see where the power curve moved as a result.
when doing the header flange, you should of taken into consideration the thickness of the material of the runners.
add that to the size of the exhaust ports.
Good job.
Nice sound.
It makes me think that I can do the one for my Caterham .
Awesome pipefitting Caleb, Solid work.
I remember my mate spending a fortune on a D+D exhaust for his YZF750 back in the 90’s, they were hard to get in the UK at the time of if I remember rightly
Am i the only one who thinks it sounds like a NSX ? Beautiful !
When you pulled out the second flange for the engine, I assumed you were going to break into a sponsored segment from send cut send.
Ginge....
Only thing i can say is do yourself a favor and put a turbo on it
I'm not a huge fan of the 3 cylinder sound, but you made it sound really good.
awesome. love it. nothing better than driving a slow car at the limit and especially one that sounds great.
I think I heard you driving past my neighborhood at 2a last night. JK. Sounds great! Nice work!
Now imagine that sound mated to the whining of a supercharge👌🏻👌🏻👌🏻
Super Nitrous Beat
The Honda Beat sounds amazing dude. A blast to drive with that exhaust. Brilliant
youre fab skills have come such a long way
Dude this is awesome i had a D &D on an R6 and it was loud hahaha cheers
Love the new lifts!
Me too!
Really cool build man, lots of fun in the edit too. Sub!
honestly you should start a small shop business(gingium autoworks), you have this kind of talent to just build anything
The way the muffler is mounted and the way the car sounds reminds me of the Dust Storm from Burnout Paradise haha
I have a kei truck with the same engine. Its my daily and it straight piped. Honda rice stuff soon ill cut the front springs and take out a leaf in the rear and slam it on 14 inch wheels 😂
wow, that sounds amazing, another brilliant video Gingium!
sound good, but the point is of making equal length is to make it better flow and make the gases exit in order and faster (as you said in the beginning)
Damn kei car activities, gotta make it like the MR gst like the rear strut brace or something
Can we take a moment to appreciate how good those new lifts look. Gahdang.
20.33 as i was staring i then gazed away and asked myself "shit did he know i was staring? was it that obvious" HAHAHA
Sounds like a baby s2000. Love the exhaust.
Pure joy !
Enjoyed this video !
Keep up the great work !
Sounds like a low revving mt-09 cp3 engine sick!