Mercedes W126 - Rear Window Channel Rust Repair - Part 4 Rear Window Channel Removal

แชร์
ฝัง
  • เผยแพร่เมื่อ 26 ต.ค. 2024

ความคิดเห็น • 25

  • @drywaller12345
    @drywaller12345 7 หลายเดือนก่อน +1

    very valuable lesson....saved me hours...

  • @Engineerd3d
    @Engineerd3d 3 ปีที่แล้ว +2

    That does not look too bad. Gives hope for us mortals.

  • @vintage76vipergreenBeetle
    @vintage76vipergreenBeetle 3 ปีที่แล้ว +1

    Nice job removing the panel.

  • @jamesadams2333
    @jamesadams2333 3 ปีที่แล้ว +1

    I just loving these videos! I grew up with these cars and just love their legendary status as simple and robust. So much so I can decide which to buy when I enter the car market in the near future. A 300SD or newer 2009+ W221 S550. I’m definitely leaning towards a w126 as they’re so rare in my part of the neighborhood and the fact I hate planned obsolescence and keep my cars for 10 plus years. Keep up the great work.

  • @brainwash3282
    @brainwash3282 3 ปีที่แล้ว

    Very good! After seeing your clips I now have the strong urge to get my Benz rust free in the next years. I'm excited how your reslult will turn out.

  • @georgesand4629
    @georgesand4629 3 ปีที่แล้ว +1

    Use flap disk on a die grinder sand off the rust. Get a cutting wheel and cut n weld in new metal. Drill holes every 2” on that panel and spot weld it back in. Grind the welds flush,sand,prime and paint.

    • @ImpalamansGarage
      @ImpalamansGarage  3 ปีที่แล้ว +1

      Agree. I'd rather spot weld it into place. That is the proper way.

  • @dymsza
    @dymsza 3 ปีที่แล้ว

    I got say I just love the 90's clipart style fonts intro :)

  • @light12a
    @light12a 3 ปีที่แล้ว +2

    I found I had the same brazing, I think this was factory. I did not pull my cover off. Wire wheeled and brush my rust, ground down with sand paper. Also ground down brazings on top corners, and any sharp ends. My goal is to make a nice smoth transition. Put down thick layers of POR15 and fiberglass, encapsulated both ends. When it started to harden, did final shaping and another layer. Going to let harden a few days and come back to grind down for paint and prep. Other side may get spray treated with rust encapsulator and then a think layer of cavity wax. Why is the rust hapening on these cars? I think the glazing gets old over time (mine had glazing in the corners) and the water has no place to go in the bottom channel. Give it decades, power washing on the seal and dirt/leaves, you have a recipe for disaster where water will eventually seep in. They should have provided some type of drain channel in the design. I am convinced nearly every w126 has this issue.

  • @keabot
    @keabot 3 ปีที่แล้ว

    Good job boss 👌🏽

  • @jungletension2835
    @jungletension2835 3 ปีที่แล้ว

    Are you near Pensacola I could sure use someone like you to help me with my 85 300D restoration LOL

  • @kevinpost1619
    @kevinpost1619 3 ปีที่แล้ว +1

    I had to tear out a lot of rusted out metal on the front cowl drains. Dash out, windshield out. Welded in new metal and drains. You might want to look into Bill Hirsch Miracle paint. I am vert satisfied with this product. 350SD

    • @light12a
      @light12a 3 ปีที่แล้ว +1

      I caught my rust early, had to dig out a lot of "compost". Glad i did, i found both rubber drain hoses were disconnected and deteriorating.

  • @MrEspokeY
    @MrEspokeY 3 ปีที่แล้ว

    Good job

  • @jamesbush268
    @jamesbush268 3 ปีที่แล้ว

    Hope you remember your work on the old Chevy. Looks to be maybe less work this time. Waiting on next video now.

  • @TheCanadianBubba
    @TheCanadianBubba 3 ปีที่แล้ว

    Taking your time saved you all kinds of grief, guaranteed !

    • @ImpalamansGarage
      @ImpalamansGarage  3 ปีที่แล้ว +1

      Before I go any further I've got to go get some sheet metal.

  • @Contantq
    @Contantq 3 ปีที่แล้ว +1

    Check under your back bottom seat. Ill bet water got in there at some time..

  • @Tigerfire75
    @Tigerfire75 3 ปีที่แล้ว

    Could you take a long cardboard box and plasticoat it to make a container

    • @ImpalamansGarage
      @ImpalamansGarage  3 ปีที่แล้ว

      possibly but those long totes at wally world are pretty cheap.