How To Make Arduino Flush System | DIY Home Automation Using Arduino

This video is about automatic flush system using arduino nano this is an awesome arduino projects for begineers which falls under arduino home automation all the parts needed to make this project is given below and the circuit diagram and codes is in the video
For codes please visit letsmakeprojects site
Arduino Nano amzn.to/2IVLgQt (aflate lnk)
Ultrasonic Sensor amzn.to/2XaiV1D
Jumper wires amzn.to/2ISxNce
Micro Servo amzn.to/2XeiC5J
Breadboard amzn.to/2Ys0Rwg

[@leor2252]

Awesome project, question tho, what application its used to write the code and i think is a better idea to use infrared sensors to trigger the system, setting a delay for the sensor to fixate on its target and after you finishe doing your thing the sensor will lose its target and then is where you set the servo motor to trigger the response.
Pretty cool to see the project

[@jeevanjee]

Sure Leo, I would consider making these changes in the future

[@sreenithcreations1525]

Super

[@jeevanjee]

Thank You

[@ramankedar5985]

I've searched on the letsmakeprojects site but couldn't find this project. So can you please send the exact link that will direct me to this project?
Thank you :)

[@jeevanjee]

Hi Raman, sorry to hear that, can you please search for arduino toll tax barrier or arduino food dispenser project on letsmakeprojects, the codes and circuit are same for all these, hope this helps, let me know if it helped you

[@SwimSherpaBayArea]

How would I adjust the code to say for example detect my cat on the loo for about 45 sec, wait for 15 sec, then activate the servo 180 deg counter clockwise and return? Thanks, even if you just point me in the right direction for tips.

[@jeevanjee]

You can make those changes in code please check servo delay section on code

[@GrenexPhotos]

I am here to do exactly the same! :) If you have an updated code for this, please let me know

[@muhammadaizat2556]

How about the coding if I want the servo will run when ultrasonic detect 2 times

[@Sergio-ta3krt]

Set a time. Active it if it sees long

[@TeslaDIY]

I did this project few months ago and it was working fine until recently, every other day it stops working until i unplug the power and replug it back in order to get it to work again.
Do you know what could be the issue? I am using a 5V 2a power supply. Thanks in advanced

[@jeevanjee]

please change batteries..it will help u..and reply ur results

[@TeslaDIY]

@@jeevanjee my setup does not use a portable battery, it is instead plugged in to the wall outlet with a 12v 5amp power supply

[@diplomatic_koboko]

@@TeslaDIY you may have defined a variable in the loop of your code so your Arduino runs out of memory. Define all variables outside the loop and refer to them inside the loop. Let me know if that works

[@TeslaDIY]

@@diplomatic_koboko Thanks buddy, I had swapped my DIY arduino toilet flush out with a Amazon one haha, but i also repurposed my arduino + servo setup as a auto mouse click lol, and i have learned that it was the servo's problem, probably something to do with power output of the servo i was using.

[@Sergio-ta3krt]

Man.. use PIC istead of Arduino. Arduino will stop running after some time. PIC doesnt

[@cyber_simon]

Can you share the code used for this project? Thank you.

[@jeevanjee]

Please check my community tab

[@David-designer]

send the link

[@cyber_simon]

@@David-designer You can use the code here: letsmakeprojects.com/wp-content/uploads/2021/01/arduino-hand-sanitizer-code.docx

[@Sergio-ta3krt]

I recommend everyone that, use PIC instead of Arduino. Arduino will stop processing after 2 days

[@jeevanjee]

Ok

[@ecebguys3704]

Code link please..

[@jeevanjee]

Please check letsmakeprojects. Com site

[@user-zt2ju9qg1c]

A $800-$1000 automatic toilet flusher. 🤣

[@jeevanjee]

Yeah!