I'm glad you enjoyed it! If you have any specific questions or if you'd like help with a video-related topic, feel free to ask, and I'll do my best to assist you.
Maybe a long shot, but any chance you know how would I wire up a air compressor that has three capacitors? I have two runs and one start. This is an Ingersoll Rand 2475N7.5 2 stage compressor. 7.5hp.
The voltage value of running capacitor is high and the microfarad value is low. Because of the rms voltage, the capacitor which has a high voltage should be used as running capacitor. The voltage value of starting capacitor is low and the microfarad value is high.
Yes friend run capacitor connection curect.The centrifugal switch disconnects the starting capacitor after starting the motor. motor is then driven by a run capacitor.
I see that there is series connection between the running capacitor and the auxillary and main winding. Does the current passes through the auxillary winding? or no? if no, please explain @@ELTronic3
The values of the running capacitor and starting capacitor for a 1 horsepower (HP) motor can vary depending on the specific motor design and application. Typically, single-phase induction motors use capacitors for starting and running. For a 1 HP single-phase motor, the starting capacitor may have a value of around 80 to 150 microfarads (µF)(230V). This capacitor is used during motor startup to provide an initial boost to the starting torque. The running capacitor, on the other hand, is typically smaller and has a value between 5 to 30 µF(415V). This capacitor is used to improve the motor's power factor and overall efficiency during continuous operation. It's important to note that these values are approximate and should be confirmed based on the motor manufacturer's specifications, which can vary depending on factors such as motor design, voltage, and specific application requirements. It is always recommended to consult the motor's datasheet or contact the manufacturer for accurate information regarding the capacitor values for a specific 1 HP motor.
The capacitor value varies depending on the amper value obtained by the motor. www.electrical4u.net/induction-motor/how-to-run-three-phase-motor-on-single-phase-power-supply/
thanks your comment.. First identify the running winding / starting winding / common wire / centrifugal switch wire of the motor. Then connect the starting capacitor and running capacitor as shown in the video.
I know I need to swap red and black wires to change direction, what I don't know is what the hell I do with the cap since the red wire is going into both caps before the motor. Do I swap red before the caps or after right before it goes into the motor
![งมหอย จับปลา มือเปล่า หาอยู่หากินแบบวีถีอีสานกับแก๊งเซียนหรั่ง ม่วนคัก! [ขอนแก่น] @Sianstudio](http://i.ytimg.com/vi/JEJZg6N-AbU/mqdefault.jpg)
I will need to watch it a few times because this is new to me, but this is GREAT ! Thank you for this.
Thanks..friend your valuable comment..❤️❤️❤️❤️❤️ I will continue to create videos for you.
Very well displayed makes understanding much easier
Thanks your comment.
Did you gain more understanding by watching this video?
@@ELTronic3 It simplified al the questions I had, Thank you
That was F'n excellent. Thank you.
I'm glad you enjoyed it! If you have any specific questions or if you'd like help with a video-related topic, feel free to ask, and I'll do my best to assist you.
How to contact you nid help to my motor..actually it's a twin capacitor 2.2kw 3hp 4p motor used in compressor
Hello my dear new friend,very informative tutorial like big, fully watched from philippines👇🏿👇🏿👇🏿👇🏿👇🏿👍🤝🙏🏼👏
Thanks..🤗
Watch my other video too..
I will continue to create videos for you.👍🤗
Thank U Sir❤❤❤
You're welcome! If you have any more questions or need further assistance, feel free to let me know.
Nice job. 💪 thank you...
😍😍😍😍 ela ela kolla..👍👍
Maybe a long shot, but any chance you know how would I wire up a air compressor that has three capacitors? I have two runs and one start. This is an Ingersoll Rand 2475N7.5 2 stage compressor. 7.5hp.
The main purpose of increasing the capacitors is to increase the value of the capacitors.
A higher value should be applied to the starting capacitor and a lower value to the run capacitor.
Nice work keep it up
😍😍😍😍 thanks
👍👍✅
Good work
Thanks.😍
Thank you for that sharing.
Ok friend..watch my other video and subscribe my chanel. thanks 😍😍
Very goooooood
Thanks bro...
sir please give us computations for running and starting cap for induction motor
Stating capacitor 100/150/200uf -- 230V
Running capacitor 20/40/60uf-- 415V
Both capacitors will not short while starting?
The two capacitors are turned on together and then one capacitor is disconnected from the centrifugal switch.
Can use both starter capacitor?
The voltage value of running capacitor is high and the microfarad value is low. Because of the rms voltage, the capacitor which has a high voltage should be used as running capacitor.
The voltage value of starting capacitor is low and the microfarad value is high.
Does the run capacitor wired correct? When motor runs, it bypass the run capacitor!
Yes friend run capacitor connection curect.The centrifugal switch disconnects the starting capacitor after starting the motor.
motor is then driven by a run capacitor.
I see that there is series connection between the running capacitor and the auxillary and main winding. Does the current passes through the auxillary winding? or no? if no, please explain
@@ELTronic3
Actually starting winding is cut after start the motor, but in this it is always connected
Can I plug 4hp motor to an outlet?
If 230v ac, use 15A plug base and use 2.5 sq mm wire
Thenxsh sir
Ok.pls watch my other videos.
for 5HP 3 phase motor to run single phase... how much MFD capacitor should i use for start and running?
A 50uf / 400v capacitor should be inserted between the two phases to supply two phases
Thanks
Ok friend.watch my other videos.❤️
What are the value of running capacito and starting capacitor of 1hp motor
The values of the running capacitor and starting capacitor for a 1 horsepower (HP) motor can vary depending on the specific motor design and application. Typically, single-phase induction motors use capacitors for starting and running.
For a 1 HP single-phase motor, the starting capacitor may have a value of around 80 to 150 microfarads (µF)(230V). This capacitor is used during motor startup to provide an initial boost to the starting torque.
The running capacitor, on the other hand, is typically smaller and has a value between 5 to 30 µF(415V). This capacitor is used to improve the motor's power factor and overall efficiency during continuous operation.
It's important to note that these values are approximate and should be confirmed based on the motor manufacturer's specifications, which can vary depending on factors such as motor design, voltage, and specific application requirements. It is always recommended to consult the motor's datasheet or contact the manufacturer for accurate information regarding the capacitor values for a specific 1 HP motor.
For 3 HP three phase motor what is the capacity of the condenser we have to use ?
To convert the motor into two phase
The capacitor value varies depending on the amper value obtained by the motor.
www.electrical4u.net/induction-motor/how-to-run-three-phase-motor-on-single-phase-power-supply/
Thanks ..Sorry for the late reply.
Shows me a bunch of lines but doesn't show how to actually wire the motor, useless to me.
thanks your comment..
First identify the running winding / starting winding / common wire / centrifugal switch wire of the motor. Then connect the starting capacitor and running capacitor as shown in the video.
I know I need to swap red and black wires to change direction, what I don't know is what the hell I do with the cap since the red wire is going into both caps before the motor. Do I swap red before the caps or after right before it goes into the motor
How to contact you?
supunsiri49@gmail.com
@@ELTronic3 do you have a cp number?so that I'll contact u we must sorry for bothering you..I know your the only 1 can help me .tnx
How to do ?
I went to change direction in this viedo.
Yes you can change the direction.
Watch my video.
th-cam.com/video/ZpgY9Wmwtxg/w-d-xo.html
Thank EL Tronic.
welcome friend..😍😍
Subscribe my chanel.i creating new video now (double capacitor motor with starting relay) You can watch that video later.
Puede rin po kahit mgkabaliktad yung capacitor
Walang problema kahit na palitan ang kapasitor.
Thanks your comment
Berapa nilai capasitor running dan starting nya terimakasih 🙏
En latino pues no ingles
👍👍👍👍🤗
Thanks..
Music so loud
Sorry..I will not use such music again
Hindi me likhe
आपको हिंदी में क्या जानना चाहिए
Aapka koi WhatsApp number hai
What are you want friend ...?