Is it possible to do self leveling in 2 separate layers? Suppose you wanted to raise the level a bit further, could you prime the surface and add a second layer? Not saying I miscalculated the quantity or anything.
Hi Mark. The key to successfully pouring concrete over an existing concrete surface it to ensure the two layers bond properly. You can also improve the bonding between the layers by using a scratch coat made from very wet, soupy concrete mix. Hope this helps.
Hi Danielle, you can use a diluted PVA adhesive mix to seal the floor or a suitable acrylic primer. Always check the manufacturing instructions. I hope this helps!
It should! Depending on how much you need to raise the floor by, you may have to do it in stages, always check the manufacturers instructions and allow the floor to dry out fully.
For the purpose of sealing or levelling concrete, the ratio of diluted PVA is usually 1:4. However, we'd recommend always reading the manufacturer's instructions as this may vary. Hope this helps! 😊
Hi, Ryan 👋 For this particular self-levelling compound, it needs 18hrs before having anything laid on it. Please note, not all self-levelling compounds will be the same so always check the laying instructions on the packet 😊
Hello I have laid leveling compound on a garage floor but I have not used enough and the compound I have put down needs to be raised a few mm as I have not used enough. Can I top it up? it has only been put down 24 hours but I need the level to be level with some concrete that goes round the sides of the garage. please help
Hi, Ali. Thanks for your question. Yes you should, remove everything from the room including furniture, floor coverings and the base boards. You should also make sure they fill any cracks in the existing concrete floor using a suitable filler and sealant giving it time to dry before applying the floor leveller to ensure a smooth and flat finish. Hope that helps! 😄
Would this same process work in a garage? My concrete garage floor is uneven, and not level, and wish to convert to an office, I need a level and smooth floor to paint or cover with whatever finish.
@@RedlineRossi Just replying in case anyone comes across this old thread. Garage floor should not be level. It should slope down to the garage door so that any water or other liquid run out of the garage instead of towards the house.
BTW I've looked at about 5 videos on how to level a surface area and yours was the best one! Thank you so much!!
Wow, thanks! Glad to hear that you found it helpful!
Great tutorial on leveling a concrete floor! Clear instructions and useful tips for anyone tackling this project. Thanks for sharing!
We're so happy to hear you found it helpful! 🙌
A very helpful video showing step by step procedure repairing cracked concrete with it will surely help the layman.
One's shop vac should be good to suck up concrete dust, if they install a shop vac bag in it right? Great job with the video - thank you!
Thanks so much for the lovely feedback! 😄 However, we'd advice not to use a domestic vacuum for this task.
@@bandq A shop vac is not a domestic vacuum. It's primary purpose is literally for C&D tasks such as this.
hi could this method be used on cracked ceramic floor tiles as well? Thanks
Is it possible to do self leveling in 2 separate layers? Suppose you wanted to raise the level a bit further, could you prime the surface and add a second layer? Not saying I miscalculated the quantity or anything.
Hi Mark. The key to successfully pouring concrete over an existing concrete surface it to ensure the two layers bond properly. You can also improve the bonding between the layers by using a scratch coat made from very wet, soupy concrete mix. Hope this helps.
Brilliant video this
Glad you liked it 🥰
Can PVA be used as a primer as shown in this video, with sika latex levelling compound? Or will it react and therefore an acrylic primer is required?
Hi Danielle, you can use a diluted PVA adhesive mix to seal the floor or a suitable acrylic primer. Always check the manufacturing instructions. I hope this helps!
No ,you must not use pva in floors , it can react, and won't go off or more likely won't bond and fail
Will this work if there is a big difference in the floor level?
It should! Depending on how much you need to raise the floor by, you may have to do it in stages, always check the manufacturers instructions and allow the floor to dry out fully.
You can do it when you B&Q it, yay!
@Ira Keanu spose
What's the ratio for diluted PVA?
For the purpose of sealing or levelling concrete, the ratio of diluted PVA is usually 1:4. However, we'd recommend always reading the manufacturer's instructions as this may vary. Hope this helps! 😊
Do you know what primer you should use for a concrete floor? And where I can buy it from?
Hi, Moira. An Acrylic primer should be used for a concrete floor, here's a handy link for where to buy some: rb.gy/z64nos
Hope this helps!
Hi sir, do i need to wait 4 weeks after self leveling before applying tiles?
Hi, Ryan 👋 For this particular self-levelling compound, it needs 18hrs before having anything laid on it. Please note, not all self-levelling compounds will be the same so always check the laying instructions on the packet 😊
Can you this outside in a stable ?
Can this be done to a mobile home??
A mobile home with a concrete floor?
Hello I have laid leveling compound on a garage floor but I have not used enough and the compound I have put down needs to be raised a few mm as I have not used enough. Can I top it up? it has only been put down 24 hours but I need the level to be level with some concrete that goes round the sides of the garage. please help
@@bandq do i need to prime it? would pva with water be ok
What sort of pva mix would this be?
Loving your PPE ;)
@@riverdeep399 can never be too careful
Also does one have to take off the baseboards to apply self leveler?
Hi, Ali. Thanks for your question.
Yes you should, remove everything from the room including furniture, floor coverings and the base boards.
You should also make sure they fill any cracks in the existing concrete floor using a suitable filler and sealant giving it time to dry before applying the floor leveller to ensure a smooth and flat finish. Hope that helps! 😄
I have little red quarry tiles, can the concrete levelling compound be laid on top of those?
Not sure, I always thought quarry tiles were supposed to be breathable, so putting concrete over the might trap moisture
I just realized this guy is now a presenter on A Place In The Sun!🙀
Well spotted 😄🏡☀
Would this same process work in a garage? My concrete garage floor is uneven, and not level, and wish to convert to an office, I need a level and smooth floor to paint or cover with whatever finish.
Did you ever do this in Your garage? I'm looking at doing mine, and My garage floor is textured, kind of like a raked ballast.
@@RedlineRossi Just replying in case anyone comes across this old thread. Garage floor should not be level. It should slope down to the garage door so that any water or other liquid run out of the garage instead of towards the house.
17 jun 2020 9:25 pm edt:thanks
Hopefully I haven't damaged my dyson, as I 'hoovered' with it before finding this video
Oh no! 🤞😓
Just wash the filters out, the fine dust blocks them and you loose suction, once washed and dry it will be full power again
@@Fishandchips9028 Thanks, yes it did return to normal :)
ok very good
Yay
😀
good hair
I Don't Do Metric System (hate it), So that being said,👎😛