Another great build and video. I have to agree with your brother however... the earlier Spitfires had the looks. The curves of a lady, and to have had those wings 'clipped', just takes away the enduring elegance of this engineering thoroughbred and national hero. I sincerely hope you never grow tired of building and posting videos of your exceptional creations. Very enjoyable watch as always. Mark, Lincolnshire, UK.
I think the fuel tank cover you applied putty to, on the real spitfire it sits slightly proud either side so wouldn't sit flush, if you look on the airfix 1/24 kit its molded on and you can see that it sits that way and not fitted flush with the rest of the panels, still, a fantastic build!!..
Good to know the panel should sit proud, the problem still remains, though, the panel is too narrow and would need significant build up to get it to sit proud. It would be nice if there were an aftermarket part out there to fix it.
Hi Brett. Wow - looks amazing! Love the weathering effect from the masking fluid. Your videos and explanations are super helpful - and inspirational! I am looking at getting back into model building after 30 years of family, work and other commitments. Haven't built a model in 30 years! But am looking forward to starting again. May have lots of questions (be prepared) :-) If my first few kits turn out even half as good as yours I'll be thrilled! Thanks for sharing and inspiring! Looking forward to more.... (have subscribed).
Thanks for the sub Wayne and I’m glad you are enjoying the videos. I am always happy to help someone get back into the hobby! Feel free to leave a comment on any of my videos, email me directly at hammerheadmodelmaking@gmail.com or DM me on Instagram (that’s where I’m most active, but I’ll answer any of the above! -Brett
Nice build, I built the same model. I put the fuselage together firts and then the assembled cockpit, then the lower wing and closed out with the upr wing half. I used a way les putty of fuselage.
I found it quite easy to slightly bend the hood outwards. The "soft" airfix plastic really shines here. It is not too brittle for this approach and is much easier to get a really good fit side to side.
I enjoyed this build very much, thanks for posting it. I did have a question though. Wouldn't a piece of plasticard on both inside fuselage halves have forced the cowl to open and helped that fit?
Thanks Ralph, I did try this, along with putting in a section of sprue to try and spread it, however, the cowl piece was surprisingly thick and resistant to bending and it ended up breaking any plastic I used to try and get it to seat correctly. In the end I felt that the filler would be the least painful way of dealing with the issue and not put physical stress on the model that could later fail and break. But, great idea and thank you for suggesting it!
@@HammerheadModelMaking As skillful as you are, I should have known you would try the inserts berore taking on the filling and sanding. Thank you for your reply
Great build! New subscriber here and just getting back into the hobby. I have this kit and will build it sometime after I have practiced my skills on some lesser kits first. But I have one question - I’m interested to know how many hours this took you to complete?
Glad to hear you are getting back into the hobby, it's always a good day when our hobby grows! I generally don't track how long it takes me to complete each project, unless I'm doing a commissioned piece, however, single engine fighters like this one generally take me about 20 hours to complete start to finish. That's usually spread out over about a 2 - 3 week period. Thanks for the sub and for watching!
Hi, thanks for watching. Yes, I have an extractor that sits above my work area and vents out to a window just behind my work area. I use mostly acrylic paints, but it still helps to keep my studio/office clean. I still wear a respirator when painting any lacquers though, even with the extractor.
Why oh why did they make that fuel tank cover in front of the cockpit a separate part?? would be a five star kit if had just made it part of the fuselage moulding..
The only reason I can think of is that there is some inscribed detail right on the top of that panel that would be difficult to restore if there was a large seam right down the middle.
I made this kit in 2019 and had the same issues as you. Airfix have released the Mk XVIII using the same sprues. I wonder if they've corrected those issues. Great work btw!
Comprehending a Zen Buddhist Koan might be easier than having any comprehensive knowledge of Spitfire marks and their at least three different wing loadouts.
@@HammerheadModelMaking It's all about the enjoyment at the end of the day. Now do an Oscar or a Frank and chip the bejeezuz out of it. It's very therapeutic :P.
Another great build sir. Airfix really have uped their game in the last few years. Keep modelling along
I agree, I’ve been enjoying their kits so far, thanks for watching!
great looking spitfire there and agreed, the shape and size of this variant makes it menacing indeed compared to the earlier versions. 👍
Thanks man! Glad there are others who agree about look of these later spitfires.
Your brother had good taste, the Spitfire has always my favorite also
It is undoubtably a beautiful and iconic aircraft!
Another great build and video. I have to agree with your brother however... the earlier Spitfires had the looks. The curves of a lady, and to have had those wings 'clipped', just takes away the enduring elegance of this engineering thoroughbred and national hero. I sincerely hope you never grow tired of building and posting videos of your exceptional creations. Very enjoyable watch as always. Mark, Lincolnshire, UK.
No need to worry, 30 years into this hobby and I have yet to come close to tiring of it!
I think the fuel tank cover you applied putty to, on the real spitfire it sits slightly proud either side so wouldn't sit flush, if you look on the airfix 1/24 kit its molded on and you can see that it sits that way and not fitted flush with the rest of the panels, still, a fantastic build!!..
Good to know the panel should sit proud, the problem still remains, though, the panel is too narrow and would need significant build up to get it to sit proud. It would be nice if there were an aftermarket part out there to fix it.
Just purchased this Spitfire Brett, can't wait to give it a go. Nice build.
Awesome! Just watch out for that panel in front of the cockpit!
@@HammerheadModelMaking - Thanks for the heads-up Brett!
Great job ! I have this kit in my stash - great to see you build this - I can try out these techniques- thank you for sharing!
Wonderful! Good luck!
Hi Brett. Wow - looks amazing! Love the weathering effect from the masking fluid. Your videos and explanations are super helpful - and inspirational! I am looking at getting back into model building after 30 years of family, work and other commitments. Haven't built a model in 30 years! But am looking forward to starting again. May have lots of questions (be prepared) :-) If my first few kits turn out even half as good as yours I'll be thrilled! Thanks for sharing and inspiring! Looking forward to more.... (have subscribed).
Thanks for the sub Wayne and I’m glad you are enjoying the videos. I am always happy to help someone get back into the hobby! Feel free to leave a comment on any of my videos, email me directly at hammerheadmodelmaking@gmail.com or DM me on Instagram (that’s where I’m most active, but I’ll answer any of the above!
-Brett
Can't wait to start mine, awesome build.
Nice, good luck, watch out for the panel in front of the cockpit!
Nice build, I built the same model. I put the fuselage together firts and then the assembled cockpit, then the lower wing and closed out with the upr wing half. I used a way les putty of fuselage.
Sounds like your experience was better! Thanks for watching!
I found it quite easy to slightly bend the hood outwards. The "soft" airfix plastic really shines here. It is not too brittle for this approach and is much easier to get a really good fit side to side.
I had tried putting a spacer in there to bend it outwards without luck, perhaps I was doing it wrong.
Love this kit, have made about 5 of them haha.
Nice! Thanks for watching!
I enjoyed this build very much, thanks for posting it. I did have a question though. Wouldn't a piece of plasticard on both inside fuselage halves have forced the cowl to open and helped that fit?
Thanks Ralph, I did try this, along with putting in a section of sprue to try and spread it, however, the cowl piece was surprisingly thick and resistant to bending and it ended up breaking any plastic I used to try and get it to seat correctly. In the end I felt that the filler would be the least painful way of dealing with the issue and not put physical stress on the model that could later fail and break. But, great idea and thank you for suggesting it!
@@HammerheadModelMaking As skillful as you are, I should have known you would try the inserts berore taking on the filling and sanding. Thank you for your reply
@@ralphford4302 no worries man, the fact we both went to the same solution first means we’re on the same wavelength!
Thank you very much for these videos, they are awesome! 9:07 What knife do you use with the Tamiya micro saw blades?
Thanks for watching! Glad you enjoyed it. I’m just using a standard xacto knife handle with the micro saw blade.
Great build!
New subscriber here and just getting back into the hobby. I have this kit and will build it sometime after I have practiced my skills on some lesser kits first. But I have one question - I’m interested to know how many hours this took you to complete?
Glad to hear you are getting back into the hobby, it's always a good day when our hobby grows! I generally don't track how long it takes me to complete each project, unless I'm doing a commissioned piece, however, single engine fighters like this one generally take me about 20 hours to complete start to finish. That's usually spread out over about a 2 - 3 week period.
Thanks for the sub and for watching!
Great looking model mate 😉👌
I appreciate that, thanks for watching!
@@HammerheadModelMaking respect where it's due mate, happy modelling
😉👍
Hello Brett, love your videos, do you use extraction when using your airbrush, thanks Paul
Hi, thanks for watching. Yes, I have an extractor that sits above my work area and vents out to a window just behind my work area. I use mostly acrylic paints, but it still helps to keep my studio/office clean. I still wear a respirator when painting any lacquers though, even with the extractor.
Thankyou
I love it!!!
Thanks Matt!
Why oh why did they make that fuel tank cover in front of the cockpit a separate part?? would be a five star kit if had just made it part of the fuselage moulding..
The only reason I can think of is that there is some inscribed detail right on the top of that panel that would be difficult to restore if there was a large seam right down the middle.
ive got this to build ... Not done any since many years ok if i can get 10% of this look i be happy
Now is a good time to get back into it! Overall the kit is real nice, just watch out for that cowl piece just in front of the cockpit.
I made this kit in 2019 and had the same issues as you. Airfix have released the Mk XVIII using the same sprues. I wonder if they've corrected those issues. Great work btw!
Good question. Maybe I’ll have to put that kit on the wish list and find out.
Comprehending a Zen Buddhist Koan might be easier than having any comprehensive knowledge of Spitfire marks and their at least three different wing loadouts.
so true!
Nice job but seriously the paint chipping is more suitable for a Japanese aircraft than late war RAF.
I fully admit I went pretty far on the chipping, certainly not realistic, but very enjoyable and good practice!
@@HammerheadModelMaking It's all about the enjoyment at the end of the day. Now do an Oscar or a Frank and chip the bejeezuz out of it. It's very therapeutic :P.
@@michaelforsythe4335 Yeah, I need to add those to my list to build!
"XIV" is pronounced "fourteen".
Right you are, my brain experienced a bit of a block while I was recording hence me sounding like a noob.
@@HammerheadModelMaking Fair enough. Just don't you DARE ever refer to the MK 103 cannon as the "Mark 103" cannon.
@@Mishn0 I’ll be sure to keep that it mind!
Loved it........!
Much appreciated!