My Maytag maxima machine posted these error codes, and this video helped me fix it, thank you! I had to take apart the front, and found my drain plug completely full of junk, muck, coins and more! Sadly though, the drain wasn’t the problem. To get to the MCU, I took apart the back, which was an easier angle for me. I checked the circuit board on the MCU by removing it from the plastic casing. Then it was plain to see on the underside of the board where it met the plastic, that it had burn marks. Totally fried. I purchased a new one for $300 and solved the problem! I was hoping for just a plugged drain, but happy that I was able to save some money on a repair person by fixing it myself. Thanks again!
Thank you so much for this video my washing machine just broke and it was giving me these error messages - it's Christmas week and I don't have the time or money to wait for repair man, so I waited for my husband to go to sleep and as a fairly bougie stay at home mom I was able to fix my machine!! It was very easy!
Had error code F06 E01/02.....took back off ONLY and was able to clean out drain and replaced MCU and the washer works perfectly!! Thanks guys, for all the help!!! Don't take off the front and door, you don't need to!!
If your error code is E01 and F06, the problem most likely has nothing to do with the first part of this video. E01 and F06 most likely means the MCU needs to be replaced, which is much much easier to access by removing the rear panel. Remove the rear panel and the MCU will be down on the lower left and is easy to remove. There is a small clip on the lower part of the white box that is facing you. Release the clip and slide the box towards you. Then, once you disconnect the wires you can remove the mother board by releasing the three clips that hold it in place. Search for a small burn mark on the inside of the white housing. If you see one, you'll probably also be able to see the damaged motherboard. MCU. That's what you need.
I get these error codes but then I just rerun the cycle and it washes all the way through. This happens every single time I wash my stuff.. any advice?
Checked the drain pump screen and it was clear. Ordered the mcu and now it works. But as some others have mentioned, don't take off the front panel. You're better off servicing from the back since you have to take it off anyways for the mcu. Thanks and enjoy
I did everything like you did in the video, the drain was completely clogged (twice as bad but I made 73 cents in change in the trap). I cleaned the door and put everything back together. I start a wash cycle and everything starts up and sound the same to what I am used to hearing except when the water should start to fill up, there is silence( and yes, I turned it back on), then the F01 and F06 code pop up. I unplug the machine checked the water hoses and blow air threw them. Tighten everything up, plug it back in and try again. Nope, same codes. Then I read all the comments and someone unplugged ti for a few minutes. Tried this and ran another cycle. YEAH YEAH YEAH. Woman vs machine... Woman won!!!!!!
I had a error code F06 E02 opened it up, the filter was a little clogged but it didnt fix the problem, so i replace that control Board and then it worked. Thanks ebay 100 bucks
Huge THANK YOU! My whirlpool Duet washer gave an E01 and F01 error. It’s about 9 years old and was able to access the drain filter from the front (followed all your steps) but noticed the rubber lining was difficult to unhook. There was enough slack in this to move the front panel away and access the drain plug. Thanks again for posting this! The issue was a plastic toy gold coin that must have been in one of my kids pockets about the size of a silver dollar coin. 😆
I had a solid front panel Whirlpool Duet wfw95hexl2 Machine stopped with F06 E02, tired to run diags and motor didn't turn (not sure if this should have clued me in on MCU failure but this happened). After a a power reset I had F01 E02 (F06 went away, likely cause the motor would respond at all), so I then tried cleaning the trap (as indicated in this video but it didn't help, was pretty clogged though so it was good). No need to remove the front door completely, just stop watching at 1:23 (You can definitely remove the trap from the left or right side working with the door in the way.) The pump is held in place with a rubber red grommet, you can turn that grommet 90 degrees and then slide the pump assembly towards you, this makes it easier to drain into a shallow pan. (or wife's cookie sheet). If the trap cleaning doesn't fix the problem DO NOT TRY TO REMOVE THE MCU THROUGH THE FRONT. on this style of machine trying to unplug the wires is by no means easy word easy. Simply pop the 12 screws and open the back up, the MCU is in the lower right left corner, snip the ziptie holding some of the wires to the MCU housing, disconnect the three wires and remove the unit. I got a factory new MCU for 180 at the local Sears Parts and Service center. Replacing the MCU solved the problem, but I suggest plugging it in and running through a 30min rinse cycle to be sure your unit is working.
This worked for us! Thanks! The pump was jammed with strands from a rug. Googling F01 error code says it’s the control board, so I doubted it would be the pump/strainer.
Thank you for the video. Unfortunately my problem was not the drain but the MCU. I ordered it off ebay and was able to complete the repair. Couldn't have done it without this video.
Thanks for the video, its easier to remove the door and get rid of the extra weight; its only 4 screws And you can also leave the door wires on and remove the entire module, 2 screws on the face front
You Sir, are the MAN! I had F06 E01 flashing on mine. After watching this and seeing a dirty filter can cause this it dawned on me that I washed my dogs bedding and enough hair was removed to insulate my attic. After disassembling and cleaning everything the error cleared and I was able to finish my laundry.
We took a 4 inch hole saw and cut a hole in the bottom where the coin catch is. Used a shop vac to suck up the water while reaching in and un screwing the catch. Clean out the catch and carried on. Way easier than taking the whole thing apart, especially when you have a stacked set. Stupid design not to have easier access to the drain catch
Subbed and saving this video. My whirlpool duet exactly like yours just broke down today with error codes F06 and E02. I'll need this video to help and guide me fix the washer myself.
Mine is throwing codes E01 and F06. I pulled the filter out and it was terrible; a cloth face mask was in there. I just KNEW it'd work like a charm after I buttoned it all back but no. Is there a way to reset these machines or erase the codes or should that have fixed it? I tried unplugging for a few minutes and still no change.
You don't have to take the door and front off everything can be accessed from the back if you can move it out. Just remove all the hex screws and remove back panel . The pump/coin catch is just mounted on rubber feet and can easily be pulled off and cleaned from there. Also the MCU is right there as well. To me far easier than removing the door etc.
My drain was oriented to the side. I should have just removed the side. At least I know for next time. Removing the door wasn’t all that fun and getting the seal back on was not fun. Like I said. The side is coming off next time.
My drain was accessable from the bottom of the unit. I was able to lean the unit back and take off the bottom pannel with two screws and clean the drain. Of course that was not the issue thought.
Thank you for making this video. I got an E01/F01 flashing code tonight, followed your directions and now we're back in business. OBTW there was a dime in the drain obstructing the water flow.
My washer wasn’t starting and was flashing E01 then F01. So I finally found out it was the filter. So I removed the junk, there was a lot. But I’m still getting the error code...do you think I need to change the drain pump? I looked at the control board and there’s no burn marks on the back anywhere, plus I just put a new one in a year ago
Great Video. Here is a good tip. If you get your washer all the way down to the coin catch on the pump...take the pump out too and inspect. This will save you from having to do the disassemble and reassemble again because there was something stuck in pump (hockey tape).
Attention......if you are about to perform this task ...DO NOT REMOVE THE BELLOWS ( grey rubber door seal) FROM THE REAR as shown in video , just remove it from front around the door opening , it’s much easier,and you can reassemble everything and then attach seal last !!!
In terms of removing and reinstalling that ring that holds on the rubber seal, just remove the top weight and the clamp is right underneath. To make it even easier, unscrew the 'frame' that runs behind the face plate and also the nut that 'suspends' the soap dispenser drawer, after which you can move the frame gently out of the way and simply unscrew that clamp. Having this extra room takes this part of the job from mystifyingly complex (why would they design it like that?) to logically simple (though still a mite painful.)
I have a front load Whirlpool model WFW95HEXU that is not filling with water and will not spin, the drum can be spun manually after turning off machine. Error codes shown are F:01 E:02. what do you think is the problem ? The circuit control panel and the drain. or could it be the MCU?
A trusted Maytag repairman said it would be $900 to fix and that I was better off buying a new one...so I did! In fact, I bought a new set...as the washer goes, so does the dryer not too long after!
It did. Didn't realize the amount of stuff that could get down there. Coins, globs of lint, one of those kids' flossing one use things.... Either way. Love the video. If it builds up again, think I'll cut an access port into the bottom of the front panel. Might not happen again for years through. I'll wait until then. *Worst part is a friend of mine owns his own repair business for appliances. But still would've cost at least $100 for a service call.
Desperately need a second video to show the trick to putting that wire band and rubber gasket back on. By far the hardest part of the repair for me. Otherwise very helpful!!
We have Maytag MHW8000AW0 and got E1 F6 code. Removed a tire front panel as described, cleaned out drain, which was full of various items, replaced. Still shown E1 F6, so we purchased a new MCU, once it arrived in mail, completely replaced and found burnt terminals on old MCU. Now with new MCU is in place, washer turns on, but when we try to start a wash, nothing happens except the typical beep. Door won’t lock, no common sounds of wash wanting to start. Any clue? The replaces MCU was OEM and an exact match for Old MCU
In my Maytag Maxima, I heard a pop follow by a (hint of a electrical burning smell) now it reads F06 E02. I am assuming this is the MCU because the motor is not coming on?Even though the manual says CCU to UI. Thoughts?
if there was a electrical burning smell there should be evidence on the damaged piece some sort of black or burn mark etc. I would inspect the mcu and ccu and any other parts you can easily see that show signs of damage.
Okay, I replaced the MCU on my whirlpool duet. It finally worked for a week.. and then.. started throwing the same code. F6 E2. Why would it work and then stop? Was the part I bought faulty? Or do I need to replace the CCU as well? I have double checked the MCU and it looks fine, no burn marks, still looks new. I need help!!
personally, I'd just check all the electronic connections that you put back together when you re-assembled the washer. specifically, if you completely removed the button panel. I'm no expert but having two panels go bad back to back seems unlikely. your error code is a communication code between two sections of the washer, specifically the user interface (button panel) and the central control unit. my guess, a cable wasn't inserted all the way and it vibrated loose.
Thank you! Great video. The only thing I did differently was to remove the seal from the door as well. I found it really difficult to put the seal back on and fight the door too. Although getting the seal back on the door was difficult as well due to the spring tensioned metal band. I eventually used a pair of shoelaces to work it back in place.
Thanks so much for posting this video. Drain was full with gunk, coins and a key (now I have an extra house key). That rubber tub seal and wire band was a bear to put back, but got through it and my washer is happy again. Is making sure the inner tub seal is seated before use prevent larger objects from getting into the drain catch?
I cleaned the filter. Luckily mine has bottom access. The filter was full of coins and hair. The only problem I have is there is still a flashing f-1 code. Does it need to be reset? Is this normal?
Hello I have a Maytag Maxima MHW6000XW0 - I have cleaned the drain out same issue unresolved. When I run throught the quick diagnostic check it stops at C000 and will not advance further. The door locks and will not advance any further - I hear a clicking noise that appears to be comeing from the control board as if its wanting to go further but will not - does that sound like a MCU issue?
unplug It for few minutes. then plug it back it in and try and start It like normal. Leave it alone for a while and see if different codes pop up besides 00.
Very interesting video. The error I am getting is F06 E01. I was told that is likely the CCU, not the MCU and if it was the drain that another code would pop up. I ordered a new CCU and replaced it, but after I turned the machine on I got the SAME error code, so I'm thinking that is not the problem. I'm about to return the CCU and was about to give up on the machine altogether. Do you think that the MCU or the drain being clogged is the problem with that error code?
C.L.S. Allinone thanks for the video, was able to successfully clear the drain (lots of stuff there actually) but still getting the same error F6E1 after I start a rinse cycle, the door locks and hear several "clicks". I'm guessing it's the MCU or something else. Like the drain pump maybe? Never would have been able to get this far without the video though. Thanks!
Thanks so much for this informative video! My son and I were able to take the washer apart this afternoon to diagnose the problem. The drain was clean, so I'll order the MCU. Do you have any tips for changing it out?
I took it all apart it was loaded full of coins and a heck of a lot of other stuff cleaned it all out and I still get codes do I need to reset something to remove these codes? Thanks Joe
Should never have taken that off. He's an idiot to have even suggested to remove that clamp . Remove the spring retainer from inside the door. Then roll the gasket off the front lip.Easy peasy,and no career involved.Then remove the 2 or 3 screws to the door lock,depending on what lock you have.Push it through.With the screws out of the front panel,it is easily removed. In closing,DO NOT REMOVE THE BOOT CLAMP OFF THE TUB.
This was mostly helpful. Unfortunately, you skipped over how to remove the wire band. You mentioned it but didn't show it on the video. I got stuck on that part.
Sorry I didn't show the actual removal I did show where it was located at 1:24 mark though . When i was filming the video the home owner just happened to be standing in front of the camera when i was removing the band unfortunately .
I’ve had my repair guy out twice , the filters been cleaned out, he replaced a part I don’t think it was the MCU (can’t remember which one ) but it was still throwing the Fo1 O9 and SUd codes but NO backed up suds so it’s misfiring for some reason. I can’t figure it out but maybe changing the MCU is the last step. It’s driving me crazy bc the washer still has years left on her I know it. I have to figures this out. If anyone has any ideas for a machine still throwing those codes after all these things have been done , please help🙏🏼🙏🏼thank you! 3:15
Sounds like that is the problem. Also make sure your water hoses on back of machine are getting pressure and are not clogged there is a screen usually where they hookup sometimes they clog with sediment but that happens very rarely .But I'm guessing its the MCU.
I have a whirlpool duet washer front load the door was stuck and wouldn’t open I took off the front panel reached up and pulled the plastic ring unlock the door now I still have an F -01 code same as before
Done and done. Great idea. What I would strongly recommend for this is to not remove the seal. Just remove the bolts that hold the front panel in place. Tilt it forward with the seal intact and the gap gives you room to accurately measure where that access hole needs to be cut so that you can access the catch.
Do NOT remove the clamp holding the tub boot seal to the tub. You're just looking for trouble and hours of needless heartbreak. And even possibly a flooded laundry room.I wonder why he never showed you how he put it all back together? Just remove the spring from under the lip at the front part of the door deal.Pull the gasket off the lip and tuck it inside the doorway. DO NOT disconnect the wires off the door lock. Remove the screws securing it and push the lock back. With the panel screws out,the panel will easily be removed. You're welcome. I may have just saved your marriage. You're welcome.
Are you kidding me!? I have to take the whole door and front off just to clean a filter/trap! That’s a very poor design, Damn it! Anyway, I took the rubber seal off from the door panel side, seems easier to put back on than the drum side.
It's easier (less complex and faster) to just take the rear panel off and access both the MCU and drain filter. The drain filter is easily removed, cleaned and replaced (since it only requires hand tightening) from the back as well (there IS enough room to remove it and put it back in easily). The MCU is nearer the back of the machine (lower left side as viewed from the rear) too. We own a Maytag Maxima which looks pretty much identical (internally) to the unit in this video. However, our MCU P/N is W10245123.
While this was very helpful, how the heck do you loosen the wire band clamp around the inner seal? You skipped right over that part, simply saying you need to loosen it. I can barely get to it, and it looks like it’s a screw that needs to be loosened. I can’t get a screwdriver in there....
On the door trigger there’s a white plastic circle just pull on that down and it will manually unlock the door. It’s on the inside of machines have to take Lid off and reach down.
I cant just remove parts out of clients washer for no reason Duh! It's easy I promise it just snaps into place with one wire harness to unhook. some models have 1 screw that secures it into place also.
My Maytag maxima machine posted these error codes, and this video helped me fix it, thank you! I had to take apart the front, and found my drain plug completely full of junk, muck, coins and more! Sadly though, the drain wasn’t the problem. To get to the MCU, I took apart the back, which was an easier angle for me. I checked the circuit board on the MCU by removing it from the plastic casing. Then it was plain to see on the underside of the board where it met the plastic, that it had burn marks. Totally fried. I purchased a new one for $300 and solved the problem! I was hoping for just a plugged drain, but happy that I was able to save some money on a repair person by fixing it myself. Thanks again!
glad you got it fixed
Thank you so much for this video my washing machine just broke and it was giving me these error messages - it's Christmas week and I don't have the time or money to wait for repair man, so I waited for my husband to go to sleep and as a fairly bougie stay at home mom I was able to fix my machine!! It was very easy!
+Lauren Baker Great news and good job.
I wish all women as capable as you. great job.
Lauren Baker : Hi Lauren Baker! Please tell me how you can fix that issue please
Had error code F06 E01/02.....took back off ONLY and was able to clean out drain and replaced MCU and the washer works perfectly!! Thanks guys, for all the help!!! Don't take off the front and door, you don't need to!!
If your error code is E01 and F06, the problem most likely has nothing to do with the first part of this video. E01 and F06 most likely means the MCU needs to be replaced, which is much much easier to access by removing the rear panel. Remove the rear panel and the MCU will be down on the lower left and is easy to remove. There is a small clip on the lower part of the white box that is facing you. Release the clip and slide the box towards you. Then, once you disconnect the wires you can remove the mother board by releasing the three clips that hold it in place. Search for a small burn mark on the inside of the white housing. If you see one, you'll probably also be able to see the damaged motherboard. MCU. That's what you need.
I get these error codes but then I just rerun the cycle and it washes all the way through. This happens every single time I wash my stuff.. any advice?
both times for my washer it has been a plugged filter, nothing else
Checked the drain pump screen and it was clear. Ordered the mcu and now it works. But as some others have mentioned, don't take off the front panel. You're better off servicing from the back since you have to take it off anyways for the mcu. Thanks and enjoy
I did everything like you did in the video, the drain was completely clogged (twice as bad but I made 73 cents in change in the trap). I cleaned the door and put everything back together. I start a wash cycle and everything starts up and sound the same to what I am used to hearing except when the water should start to fill up, there is silence( and yes, I turned it back on), then the F01 and F06 code pop up. I unplug the machine checked the water hoses and blow air threw them. Tighten everything up, plug it back in and try again. Nope, same codes. Then I read all the comments and someone unplugged ti for a few minutes. Tried this and ran another cycle. YEAH YEAH YEAH. Woman vs machine... Woman won!!!!!!
awesome news glad you figured it out.
I had $20 in change !
I had a error code F06 E02 opened it up, the filter was a little clogged but it didnt fix the problem, so i replace that control Board and then it worked. Thanks ebay 100 bucks
Edward ko : please telling me what parts you order from eBay for replace the wash machine. Thanks advance
Ok good. If it was 300 I might as well buy another washer
I had an E1 F9 code. I had a blocked drain filter as I suspected. This video for taking my washer apart was Exactly what I needed.
How to clear codes
Huge THANK YOU! My whirlpool Duet washer gave an E01 and F01 error. It’s about 9 years old and was able to access the drain filter from the front (followed all your steps) but noticed the rubber lining was difficult to unhook. There was enough slack in this to move the front panel away and access the drain plug. Thanks again for posting this! The issue was a plastic toy gold coin that must have been in one of my kids pockets about the size of a silver dollar coin. 😆
Thanyou Soo much you gais save me alot of money iam did clean the filter on my washer and get good results thank for your videos
I had a solid front panel Whirlpool Duet wfw95hexl2
Machine stopped with F06 E02, tired to run diags and motor didn't turn (not sure if this should have clued me in on MCU failure but this happened). After a a power reset I had F01 E02 (F06 went away, likely cause the motor would respond at all), so I then tried cleaning the trap (as indicated in this video but it didn't help, was pretty clogged though so it was good). No need to remove the front door completely, just stop watching at 1:23 (You can definitely remove the trap from the left or right side working with the door in the way.) The pump is held in place with a rubber red grommet, you can turn that grommet 90 degrees and then slide the pump assembly towards you, this makes it easier to drain into a shallow pan. (or wife's cookie sheet).
If the trap cleaning doesn't fix the problem DO NOT TRY TO REMOVE THE MCU THROUGH THE FRONT. on this style of machine trying to unplug the wires is by no means easy word easy. Simply pop the 12 screws and open the back up, the MCU is in the lower right left corner, snip the ziptie holding some of the wires to the MCU housing, disconnect the three wires and remove the unit. I got a factory new MCU for 180 at the local Sears Parts and Service center.
Replacing the MCU solved the problem, but I suggest plugging it in and running through a 30min rinse cycle to be sure your unit is working.
Game of Cones ddd
Took the MCU out will see little chip on the back panel got burn ,
replace MCU right away and that cost you around 200 buck
good luck
Wow, you are the greatest! My Machine was clogged and your video help me fix it myself. You save me hundreds on a service call, Thanks
Juan Marte your welcome thanks for watching
This worked for us! Thanks! The pump was jammed with strands from a rug. Googling F01 error code says it’s the control board, so I doubted it would be the pump/strainer.
Thank you for the video. Unfortunately my problem was not the drain but the MCU. I ordered it off ebay and was able to complete the repair. Couldn't have done it without this video.
Thanks for the video, its easier to remove the door and get rid of the extra weight; its only 4 screws
And you can also leave the door wires on and remove the entire module, 2 screws on the face front
You Sir, are the MAN! I had F06 E01 flashing on mine. After watching this and seeing a dirty filter can cause this it dawned on me that I washed my dogs bedding and enough hair was removed to insulate my attic. After disassembling and cleaning everything the error cleared and I was able to finish my laundry.
Mine was full of dog hair as well.
We took a 4 inch hole saw and cut a hole in the bottom where the coin catch is. Used a shop vac to suck up the water while reaching in and un screwing the catch. Clean out the catch and carried on. Way easier than taking the whole thing apart, especially when you have a stacked set. Stupid design not to have easier access to the drain catch
Subbed and saving this video. My whirlpool duet exactly like yours just broke down today with error codes F06 and E02. I'll need this video to help and guide me fix the washer myself.
Mine is throwing codes E01 and F06. I pulled the filter out and it was terrible; a cloth face mask was in there. I just KNEW it'd work like a charm after I buttoned it all back but no. Is there a way to reset these machines or erase the codes or should that have fixed it? I tried unplugging for a few minutes and still no change.
You don't have to take the door and front off everything can be accessed from the back if you can move it out. Just remove all the hex screws and remove back panel . The pump/coin catch is just mounted on rubber feet and can easily be pulled off and cleaned from there. Also the MCU is right there as well. To me far easier than removing the door etc.
EXACTLY, TONY!! We did everything we needed to do from the back without removing any of the front!
My drain was oriented to the side. I should have just removed the side. At least I know for next time. Removing the door wasn’t all that fun and getting the seal back on was not fun. Like I said. The side is coming off next time.
My drain was accessable from the bottom of the unit. I was able to lean the unit back and take off the bottom pannel with two screws and clean the drain. Of course that was not the issue thought.
my drain was at the front of the washer, awful spot. Tilted the washer up against the wall and cleaned it out that way
Thank you. This really helped. Mine was harder to get to and at a bad angle but this helped me fix it and it took less time than I thought. ❤️
Thank you for making this video. I got an E01/F01 flashing code tonight, followed your directions and now we're back in business. OBTW there was a dime in the drain obstructing the water flow.
Glad it helped out
Maytag f01 flashing code what does it mean and how do I fix it
My washer wasn’t starting and was flashing E01 then F01. So I finally found out it was the filter. So I removed the junk, there was a lot. But I’m still getting the error code...do you think I need to change the drain pump? I looked at the control board and there’s no burn marks on the back anywhere, plus I just put a new one in a year ago
Great Video. Here is a good tip. If you get your washer all the way down to the coin catch on the pump...take the pump out too and inspect. This will save you from having to do the disassemble and reassemble again because there was something stuck in pump (hockey tape).
Thanks. Good tip
Attention......if you are about to perform this task ...DO NOT REMOVE THE BELLOWS ( grey rubber door seal) FROM THE REAR as shown in video , just remove it from front around the door opening , it’s much easier,and you can reassemble everything and then attach seal last !!!
Yes, absolutely. No reason you ever need to remove that rear seal unless you're replacing the seal itself.
In terms of removing and reinstalling that ring that holds on the rubber seal, just remove the top weight and the clamp is right underneath. To make it even easier, unscrew the 'frame' that runs behind the face plate and also the nut that 'suspends' the soap dispenser drawer, after which you can move the frame gently out of the way and simply unscrew that clamp. Having this extra room takes this part of the job from mystifyingly complex (why would they design it like that?) to logically simple (though still a mite painful.)
I have a front load Whirlpool model WFW95HEXU that is not filling with water and will not spin, the drum can be spun manually after turning off machine. Error codes shown are F:01 E:02. what do you think is the problem ? The circuit control panel and the drain. or could it be the MCU?
i have a eo1 fo1 error code. i tried cleaning the drain but still getting the error. will this work for me?
A trusted Maytag repairman said it would be $900 to fix and that I was better off buying a new one...so I did! In fact, I bought a new set...as the washer goes, so does the dryer not too long after!
This helped so much!!! Helped me avoid an expensive repair call that I was able to do myself in under an hour.
glad it helped.
It did. Didn't realize the amount of stuff that could get down there. Coins, globs of lint, one of those kids' flossing one use things.... Either way. Love the video. If it builds up again, think I'll cut an access port into the bottom of the front panel. Might not happen again for years through. I'll wait until then.
*Worst part is a friend of mine owns his own repair business for appliances. But still would've cost at least $100 for a service call.
+Dwain Moore good job doing the labor your self and saving some money.
Desperately need a second video to show the trick to putting that wire band and rubber gasket back on. By far the hardest part of the repair for me. Otherwise very helpful!!
It can be a little tricky
If you took the front panel off to clean the filter - It needs to be put back on to trip the mounted ground switch or you will get a F6 error
We have Maytag MHW8000AW0 and got E1 F6 code.
Removed a tire front panel as described, cleaned out drain, which was full of various items, replaced. Still shown E1 F6, so we purchased a new MCU, once it arrived in mail, completely replaced and found burnt terminals on old MCU.
Now with new MCU is in place, washer turns on, but when we try to start a wash, nothing happens except the typical beep. Door won’t lock, no common sounds of wash wanting to start.
Any clue? The replaces MCU was OEM and an exact match for Old MCU
did you end up fixing the issue?
In my Maytag Maxima, I heard a pop follow by a (hint of a electrical burning smell) now it reads F06 E02. I am assuming this is the MCU because the motor is not coming on?Even though the manual says CCU to UI. Thoughts?
if there was a electrical burning smell there should be evidence on the damaged piece some sort of black or burn mark etc. I would inspect the mcu and ccu and any other parts you can easily see that show signs of damage.
it is easy to take off the front bellow clamp instead of the inside clamp bellow will stay with the outer Shelf
Good call. I wound up doing that to put it back together.
I did as well. Thank you for suggestion! Saved me a lot of frustration!
Okay, I replaced the MCU on my whirlpool duet. It finally worked for a week.. and then.. started throwing the same code. F6 E2. Why would it work and then stop? Was the part I bought faulty? Or do I need to replace the CCU as well? I have double checked the MCU and it looks fine, no burn marks, still looks new. I need help!!
personally, I'd just check all the electronic connections that you put back together when you re-assembled the washer. specifically, if you completely removed the button panel.
I'm no expert but having two panels go bad back to back seems unlikely. your error code is a communication code between two sections of the washer, specifically the user interface (button panel) and the central control unit. my guess, a cable wasn't inserted all the way and it vibrated loose.
Makeup By Shanda I would call a technician if I'll be you
Thank you! Great video. The only thing I did differently was to remove the seal from the door as well. I found it really difficult to put the seal back on and fight the door too. Although getting the seal back on the door was difficult as well due to the spring tensioned metal band. I eventually used a pair of shoelaces to work it back in place.
your welcome glad it helped out.
That tension spring is difficult. I still don't have it on correctly
Thanks so much for posting this video. Drain was full with gunk, coins and a key (now I have an extra house key). That rubber tub seal and wire band was a bear to put back, but got through it and my washer is happy again. Is making sure the inner tub seal is seated before use prevent larger objects from getting into the drain catch?
Definitely would be good to check seal. It's almost magic the stuff that ends up and the drain.
Thank you! Was a pain to put back together, but it solved our problem without spending $$$. 👍🏻😀
I cleaned the filter. Luckily mine has bottom access. The filter was full of coins and hair. The only problem I have is there is still a flashing f-1 code. Does it need to be reset? Is this normal?
Thanks big help. Was clogged with major stuff.
Hello I have a Maytag Maxima MHW6000XW0 - I have cleaned the drain out same issue unresolved. When I run throught the quick diagnostic check it stops at C000 and will not advance further. The door locks and will not advance any further - I hear a clicking noise that appears to be comeing from the control board as if its wanting to go further but will not - does that sound like a MCU issue?
unplug It for few minutes. then plug it back it in and try and start It like normal. Leave it alone for a while and see if different codes pop up besides 00.
Very interesting video. The error I am getting is F06 E01. I was told that is likely the CCU, not the MCU and if it was the drain that another code would pop up. I ordered a new CCU and replaced it, but after I turned the machine on I got the SAME error code, so I'm thinking that is not the problem. I'm about to return the CCU and was about to give up on the machine altogether. Do you think that the MCU or the drain being clogged is the problem with that error code?
Jason Poreda definitely worth checking drain first.
C.L.S. Allinone thanks for the video, was able to successfully clear the drain (lots of stuff there actually) but still getting the same error F6E1 after I start a rinse cycle, the door locks and hear several "clicks". I'm guessing it's the MCU or something else. Like the drain pump maybe?
Never would have been able to get this far without the video though. Thanks!
Jason Poreda your welcome
Just wanted to say Thank You again! Replaced the MCU (found one at Sears parts direct for $192) and presto! It works again.
glad to hear you got it fixed
did the fix now the set the washer to normal setting and the normal light just blinks and nothing happens when I press start? Any suggestions?
thanks guys it worked great I sure wish we had the lower panel
Your welcome. Stupid design without bottom panel for sure .
+C.L.S. Allinone I said a few bad words lol
I had error F1 E02, I tried all the normal fixes and nothing worked, but after leaving it turned off at the mains for 15 minutes it worked perfect
thank you very much. it fix the problem
Thanks so much for this informative video! My son and I were able to take the washer apart this afternoon to diagnose the problem. The drain was clean, so I'll order the MCU. Do you have any tips for changing it out?
glad i could help . It's fairly easy you shouldn't have any problems
Very helpful! Thanks!
Thank you! This video saved me!
thank you bunches. you really are a life saver
your welcome
I took it all apart it was loaded full of coins and a heck of a lot of other stuff cleaned it all out and I still get codes do I need to reset something to remove these codes? Thanks Joe
sounds like your MCU is bad unfortunately if your still getting codes. there is a link in description for MCU it's a little pricey
Thanks for the video! Now I’m trying to but it back together. It is hard to but the rubber and metal ring back on. Any suggestions?
Should never have taken that off. He's an idiot to have even suggested to remove that clamp . Remove the spring retainer from inside the door. Then roll the gasket off the front lip.Easy peasy,and no career involved.Then remove the 2 or 3 screws to the door lock,depending on what lock you have.Push it through.With the screws out of the front panel,it is easily removed. In closing,DO NOT REMOVE THE BOOT CLAMP OFF THE TUB.
This was mostly helpful. Unfortunately, you skipped over how to remove the wire band. You mentioned it but didn't show it on the video. I got stuck on that part.
Sorry I didn't show the actual removal I did show where it was located at 1:24 mark though . When i was filming the video the home owner just happened to be standing in front of the camera when i was removing the band unfortunately .
I’ve had my repair guy out twice , the filters been cleaned out, he replaced a part I don’t think it was the MCU (can’t remember which one ) but it was still throwing the Fo1 O9 and SUd codes but NO backed up suds so it’s misfiring for some reason. I can’t figure it out but maybe changing the MCU is the last step. It’s driving me crazy bc the washer still has years left on her I know it. I have to figures this out. If anyone has any ideas for a machine still throwing those codes after all these things have been done , please help🙏🏼🙏🏼thank you! 3:15
Awesome instructions, it fixed my machine! But HELP! I guess I didn’t put it back together correct cuz it’s leaking water. What did I do wrong?!
I cleaned the drain. Started it up but I don't hear any water to start the cycle. Same error. Would this still mean that the mcu needs to be replaced?
Sounds like that is the problem. Also make sure your water hoses on back of machine are getting pressure and are not clogged there is a screen usually where they hookup sometimes they clog with sediment but that happens very rarely .But I'm guessing its the MCU.
Thanks so much for posting this! Worked like a charm!
awesome glad it worked for you
I have a whirlpool duet washer front load the door was stuck and wouldn’t open I took off the front panel reached up and pulled the plastic ring unlock the door now I still have an F -01 code same as before
Thank you man.
thank you brother you really helped me out
your welcome
Omg you make it so much harder take the from spring clamp off and take the screws off for the door latch it takes 5 seconds to do omg!!
while you have the front panel iff cut out and access hole for the catch
Done and done. Great idea. What I would strongly recommend for this is to not remove the seal. Just remove the bolts that hold the front panel in place. Tilt it forward with the seal intact and the gap gives you room to accurately measure where that access hole needs to be cut so that you can access the catch.
So i have this code, but my clothes are locked in the washer. How do you get the door to unlock?
Do NOT remove the clamp holding the tub boot seal to the tub. You're just looking for trouble and hours of needless heartbreak. And even possibly a flooded laundry room.I wonder why he never showed you how he put it all back together? Just remove the spring from under the lip at the front part of the door deal.Pull the gasket off the lip and tuck it inside the doorway. DO NOT disconnect the wires off the door lock. Remove the screws securing it and push the lock back. With the panel screws out,the panel will easily be removed. You're welcome. I may have just saved your marriage. You're welcome.
How I wish I saw this vid earlier!!!
I have a whirlpool duet (front load washer) error codes F06 & E02 blinks on display and "Door Locked" keeps flashing (I can't open the door) Help
+Joey Cabatic Washer thinks it in middle of cycle after pressing or selecting cancel/drain it should unlock within 10 minutes.
there is no "cancel" button
+Joey Cabatic should be able to select drain only.. that should do the same thing.
i got the door to open after waiting about 10 min. but error codes still appears
+Joey Cabatic I would check your drain now to see if it's clogged. just follow my video hopefully you have access panel on bottom.
Are you kidding me!? I have to take the whole door and front off just to clean a filter/trap! That’s a very poor design, Damn it! Anyway, I took the rubber seal off from the door panel side, seems easier to put back on than the drum side.
It's easier (less complex and faster) to just take the rear panel off and access both the MCU and drain filter. The drain filter is easily removed, cleaned and replaced (since it only requires hand tightening) from the back as well (there IS enough room to remove it and put it back in easily). The MCU is nearer the back of the machine (lower left side as viewed from the rear) too. We own a Maytag Maxima which looks pretty much identical (internally) to the unit in this video. However, our MCU P/N is W10245123.
Took about 3 hours, they don’t ,
Make it easy, control box was way in the back, hard to disconnect. Tip: slide it away from you to dislodge it.
If you want to get at the mcu then go in through the back it is easier
Hello, how do u fix a machine if its saying “EdI” im not sure if its a the number 1 or the letter L or I
While this was very helpful, how the heck do you loosen the wire band clamp around the inner seal? You skipped right over that part, simply saying you need to loosen it. I can barely get to it, and it looks like it’s a screw that needs to be loosened. I can’t get a screwdriver in there....
You shouldn't have removed the gasket from the inside. You could have just remove the spring clamp around the door.
I have a front load Whirlpool Duet Washer which stop during mid cycle, not draining, shows codes E01, F09 and "SUD" Do anyone know what this means?
machine has too much soap just run it a couple times without using soap
Good day! How i fix my whirlfool washing machine error EA
also, the tip of taking off the top weight block was key
Why won't you just take the door boot off the front?? Instead from the main outter tank. It way easier!! Also way less chance of have a leak or leaks.
my door is locked and has the cods to dose that mean something else is wrong to thanks
Its stuck in cycle might have to wait 10 min for it to open after canceling cycle. Try unplugging it also if waiting does not work.
Ok so would that be the board problem to I have the same trouble codes u were talking about
could still be drain problem. alot of error codes can cause the door to stay locked. start with checking drain since that's free. then MCU board next.
saved the day bro~!!
How can you tell if the board is bad???????????????????????????
ANY VIDEO ON F1/E1 FOR KENMORE TOP LOAD
THANK U
Usually it's the motor that has failed.
so great directions, awful design. found 6 cents, a few stones, lots of hair and a half dozen breastfeeding bra pads!
ok thanks
it's an expensive part so just be careful with it . If it doesn't fix the problem just return it.
I got E01/F03 does anyone know what I can do ? Help, please!
Jen, it's either the CCU or the MCU. Google the error codes and it should let you know.
I have error rES. What is that mean?
i removed the drain cap and cleaned out the drain. still has error codes.
probably the mcu unfortunately then
+clsallinone sears has good return policies for their parts I would order from them. there is a link in my description.
How do I clear the code after removing the obstruction
hello. code should clear itself if does not there is still a ongoing issue
what size socket takes out those bolts
1/4 I believe it's been a while though .
13mm
Iam getting E01 /EO3 together on whirlpool duet front loader how do i fix that
I had the F06 E01. The MCU was bad. The MCU had a bad bridge rectifier GBU8J, you can get this part for $2.
Did you repair the fusable links in the circuit board?
what does F- mean on a whirlpool duet
here is a link that might help you www.justanswer.com/appliance/3peu2-whirlpool-cabrio-washer-f-code-showing-up.html
How do i clear an f21 code
Ok how do I just unlock it to get my half-washed wet clothes out 😡
Thats what happened to me tonight.
On the door trigger there’s a white plastic circle just pull on that down and it will manually unlock the door. It’s on the inside of machines have to take Lid off and reach down.
If the MCU is so easy to change...then why NOT show it DUH !
I cant just remove parts out of clients washer for no reason Duh! It's easy I promise it just snaps into place with one wire harness to unhook. some models have 1 screw that secures it into place also.