No it's not. I own a Beretta 92x Performance as well. He may have an aftermarket threaded barrel from Beretta, or maybe a Jarvis custom threaded ? I don't think he says, but the stock factory barrel config. is a 4.9 inch, black nitride coated NON-threaded.
I also own a Beretta 92x performance! Awesome gun!!! Soon as I got mine from my FFL - it went STRAIT to my GUN SMITH and we force fed that sucker steroids and jet fuel! I've got the Lok wrap around grips on it, Beretta competition hammer, Langdon LTT OP trigger bar, Black Beard Customs Trident trigger shoe, Go-Guns gas pedal, Lok extended competition mag well, +4 Springer Preicion base pads sitting under 18 rnd. Met-Gar mags. A polish job was done on the feed ramp, and trigger components to further smooth the action and lower the trigger pull on both the da/sa... Last but not least it now has the Wilson Combat "silicone carbide" competition spring kit set up with a 12lb. hammer spring and 11lb. recoil spring. The final piece to the gun will be the compensator, but I need your advice please? (2). Questions: I have been eyeballing the Toni systems open comp. / muzzle break like the one you have, and was wondering if you are running a STOCK recoil spring with the comp. or not? ...and if not the stock spring, than what weight spring are you running?? (I know you must have to fiddle with it a bit depending on yer ammo and how it cycles... )
I will go to the range soon with a few different boxes of 9 and see if they all perform. I can't remember what I used, it ejected but didn't go far. I'll let you know. BTW - Do you know your trigger weight and do you think the Langdon LTT trigger bar worth the extra money?
@@sxs2950 Trigger weight on it right now sits at approx. 6 lbs on the double action and just under 3 pounds on the single action. Exceptionally smooth now. However, as you can guess, the 12 lb. silicone hammer spring AND the polish job on the trigger internals helped quite a bit. As far as the Langdon trigger bar goes? It was worth EVERY PENNY to me! If you buy it and put it in, you will thank me later! LOL It takes A LOT off the pre-travel in single action. A LOT! ...And just how short the re-set is now??? Mamma MIa fast!!! ( I would also STRONGLY suggest the you buy/install the Beretta match hammer as well to go along with it, if you haven't already?) Makes the trigger the way it SHOULD'VE BEEN from Beretta! Yes, great video also man, keep up the good work! Please let me know how the comp. works out with some different loads? I'd be grateful, thank you! P.S - I'm only putting defensive and range ammo through mine for now, so that's what interests me with the comp. Happy New Year '25
I've never loved a 92 but boy that's a gem.
Good thing I subbed to you a while back after some usp & vector vids. Toni systems make tons of outstanding shotgun stuff too.
Stay tuned, I have the coolest Beretta on the planet I plan on making a video about.
@@sxs2950
Sure thing.
Sal Luna just placed very well in Open division at the Georgia Sectional using a Toni System equipped 92x performance.
What dealer were you able to order the Toni systems accessories from ?
Is that the stock barrel?
No it's not. I own a Beretta 92x Performance as well. He may have an aftermarket threaded barrel from Beretta, or maybe a Jarvis custom threaded ?
I don't think he says, but the stock factory barrel config. is a 4.9 inch, black nitride coated NON-threaded.
I also own a Beretta 92x performance!
Awesome gun!!!
Soon as I got mine from my FFL - it went STRAIT to my GUN SMITH and we force fed that sucker steroids and jet fuel!
I've got the Lok wrap around grips on it, Beretta competition hammer, Langdon LTT OP trigger bar, Black Beard Customs Trident trigger shoe, Go-Guns gas pedal, Lok extended competition mag well, +4 Springer Preicion base pads sitting under 18 rnd. Met-Gar mags.
A polish job was done on the feed ramp, and trigger components to further smooth the action and lower the trigger pull on both the da/sa...
Last but not least it now has the Wilson Combat "silicone carbide" competition spring kit set up with a 12lb. hammer spring and 11lb. recoil spring.
The final piece to the gun will be the compensator, but I need your advice please?
(2). Questions:
I have been eyeballing the Toni systems open comp. / muzzle break like the one you have, and was wondering if you are running a STOCK recoil spring with the comp. or not?
...and if not the stock spring, than what weight spring are you running??
(I know you must have to fiddle with it a bit depending on yer ammo and how it cycles... )
I will go to the range soon with a few different boxes of 9 and see if they all perform. I can't remember what I used, it ejected but didn't go far. I'll let you know. BTW - Do you know your trigger weight and do you think the Langdon LTT trigger bar worth the extra money?
@@sxs2950 Trigger weight on it right now sits at approx. 6 lbs on the double action and just under 3 pounds on the single action.
Exceptionally smooth now.
However, as you can guess, the 12 lb. silicone hammer spring AND the polish job on the trigger internals helped quite a bit.
As far as the Langdon trigger bar goes?
It was worth EVERY PENNY to me!
If you buy it and put it in, you will thank me later! LOL
It takes A LOT off the pre-travel in single action. A LOT!
...And just how short the re-set is now???
Mamma MIa fast!!!
( I would also STRONGLY suggest the you buy/install the Beretta match hammer as well to go along with it, if you haven't already?)
Makes the trigger the way it SHOULD'VE BEEN from Beretta!
Yes, great video also man, keep up the good work!
Please let me know how the comp. works out with some different loads? I'd be grateful, thank you!
P.S - I'm only putting defensive and range ammo through mine for now, so that's what interests me with the comp.
Happy New Year '25