Creo que explicas muy bien y para un buen entendedor pocas palabras , aveces se olvida que hay personas , visuales , auditivas y quinostesicas. Un abrazo hermano.
La tua maestria si vede sopratutto nella scioltezza fluida della tua mano che ti dà senza alcun problema precisione e bellezza estetica. Sei un esempio per tutti! 👏👏👏
Un magnífico tutorial. maestro , se ve claramente y hacé que parezca tan fácil , gracias por compartir sus conocimientos y experiencias , un saludo cordial y por supuesto un gran like desde Narón (Galicia) 🤓🔝
Beautifully filmed and a magnificant nice looking weld. Dancing the cup needs some practice though. Thanks Sir for this educational vid. Always difficult those thin welds. Friendly regards from Holland, Marcel Knippers.
Pas mal du tout le petit tuto pour godiller en corniche, j'ai jamais réussi à choper le coup de main. En position aucun problème pour godiller mais en corniche obligé de faire a main levée
I'm just browsing and see no one answered you. He used 38 amps but you can use up to 42 works lovely as well. He also used backing gas . Pipes must be square cut filed etc i suppose you might be travelling two slow for amps your using. Good luck with it
there is a problem with my equipment. In the video, when you tap once, the dot welds and stops. On my device it stops after 3-4 seconds. What could be the reason for this?
you got robotic arm, i dont understand how you Can hold gun at handle and so far from weld and repeat the same movemt, i have to hold gun almost at the nozzle and arm must be supported
@@CottonEyeJoe_001 I drink neither of those. Then again, I’ve been *extremely* clumsy my entire life, am significantly disabled, am getting on in years, have less-good health - and most importantly of all, by far - *I do not weld for a living.* A lot of this level of skill boils down to doing it a great deal for a *very* long time. I know it has worked that way with a number of things in my life.
Walking cup is something I haven't got into. It's quite impressive technique. I usually have to prop and secure my other hand near which I can lean into to get decent results. Otherwise my hand shakes way too much. Then again I don't weld that much at work.
Y-a-t-il un bon remplissage à l'intérieur? Curieux de voir car dans l'industrie des breuvages, il faut éviter toute contamination potentielle causé par des interstices.
@@martinbank_ I weld sanitary tubing all day and always use filler (usually 1,0mm or 1,2mm). As long as the wire is clean and you keep it in the argon envelope around the cup it’s fine. I’ve never had a problem with tested sections.
![weld [HAGOJIBI]](http://yt3.ggpht.com/ytc/AIdro_lButtTy6bwshHHOdUuuc7ktsddm0YgRj2FhqoPUm3aQA=s48-c-k-c0x00ffffff-no-rj)
I could watch HAGOJIBI weld for hours. An absolute master of his craft. All respect, Sir!
This exactly what I been waiting for thin stainless tube welding. It’s about time. Thank you, More please😀
Every morning before go to work I watch one of your blog about welding..and learn more about it
Большое Вам спасибо! Как раз такие. штучки я и варю. Очень пригодился Ваш урок, буду смотреть дальше. Благодарю
i love it universal, you dont even need to talk and this video gives me more info on the subject than any of the other vids!!
There is subtitles. 😉
Браво, очень интересно и приятно смотреть на работу профессионала.
Creo que explicas muy bien y para un buen entendedor pocas palabras , aveces se olvida que hay personas , visuales , auditivas y quinostesicas. Un abrazo hermano.
La tua maestria si vede sopratutto nella scioltezza fluida della tua mano che ti dà senza alcun problema precisione e bellezza estetica. Sei un esempio per tutti! 👏👏👏
Un magnífico tutorial. maestro , se ve claramente y hacé que parezca tan fácil , gracias por compartir sus conocimientos y experiencias , un saludo cordial y por supuesto un gran like desde Narón (Galicia) 🤓🔝
행님 30만 축하드립니다
참 오래되었는데 형님 영상보고 그동안 열심히 살아서 이제 좀 한다 소리듣지만서도
아직 갈길이 너무 멉니다
건강하시고 30만 축하드립니다
감사합니다. 앞으로 더 큰 성공 이루시고 돈도 마니마니 버시고 건강하시길 바랄께요
Beautifully filmed and a magnificant nice looking weld. Dancing the cup needs some practice though. Thanks Sir for this educational vid. Always difficult those thin welds. Friendly regards from Holland, Marcel Knippers.
Dancing is open to interpretation 💃
@@PulpFictionized 👌
Very nice.... Yarikata ga ore WA suki desu
спасибо за хорошие видео !!!! с наступающими праздниками!!!!
오늘도 한수 배웠습니다
감사합니다^^
The BEST welder around the wordl
Thank you so much for this video❤
Attracted towards TIG, Hi u r good👍
항상 영상잘보구 배워갑니다
궁금한게잇는데요
퍼지 하는 방법 영상도 만들어 주시면 안되나요 ?
tolles Video, ohne Schweißdraht, wieviel Formiergas?
Thank you.MASTER
手腕 要這樣擺動 有一點困難 還有其他方式嘛？
当然，还有其他的焊接方法。 我的频道上已经有那个视频了。 请参考。 另一种方法将在后面介绍。
궁금한게있습니다.
sus용접은 잘되는데, 쎄니타리 배관할때는 구멍이나던가 산화가 되는데
용접전류를
sus보다 낮춰야하나요?
보여드린 전류 사용해보시고 상황에 맞게 조금씩 조절해보시면 좋아지실 겁니다.
구멍이 나는이유는 전류가높거나 진행이 늦어서 그런거같고 . . 산화는 퍼지를 하고 가스를 높여주면 될거같네요 .
Your video is very clear, what did you use to shoot it?
I took a video with my smartphone.
wellder Cakep dan rapih.
Pas mal du tout le petit tuto pour godiller en corniche, j'ai jamais réussi à choper le coup de main.
En position aucun problème pour godiller mais en corniche obligé de faire a main levée
You are truly. A master!
Спасибо за обзор!🤝
아이디어가 참 다양한 것 같아요 저도 용접을 한지 25년이 되었습니다 참 멋지시네요 존경합니다 ㅎㅎ 😂
덕분에 용접을 향상시킬 수 있습니다. Gracias a ti voy a mejorar mi soldadura.🤗
Thank you
Always top 🌟🌟👊👊
Thanks for tips ❤️ I will try it too❤️
Could you help with a 1 1/4 " purge stainless steel elbow? I was struggling 😬 you're one of the best thank you for your time!!
SOS loco hagojibi 💪🏽👏🏼🇦🇷⚽
It's great 👍
Jongyeong! ( Respect! )
Thanks for sharing
잘보고감니다 ㅎㅎ😅
Excellent
What amps would you normally use on that type of thin pipe without getting burn through
I'm just browsing and see no one answered you. He used 38 amps but you can use up to 42 works lovely as well. He also used backing gas . Pipes must be square cut filed etc i suppose you might be travelling two slow for amps your using. Good luck with it
@@martinfanagan8374 thanks bro bless
Nice, and how can you manage not to blow a hole when you keep turning on the torch.., is it becoz of the low current?
Show !!!!!🔥🔥🔥🔥🚀🚀🚀
Thanks you Best Master
Parfait bro ❤
Спасибо за урок, на малых диаметрах мне тяжело пока варить)
굳입니다
Can you tell me about all the preparation all processes the materials tungsten amper volt and how to use pulse tig
Sehr gut!
Que amperaje usas para ese tipo de lámina??
Simply beautiful!
HOLA MAESTRO , YA TIENE NUEVO SUSCRIPTOR, Y KN TODO RESPETO, TIENE ARTE EN SUS MANOS , SALUDOS DESDE HOUSTON TX USA
Good
Sensacional 👏👏👏👏👏👏 parabéns
Super
Thanks boss
there is a problem with my equipment. In the video, when you tap once, the dot welds and stops. On my device it stops after 3-4 seconds. What could be the reason for this?
Try checking your downslope setting on your machine. set it to 0
That pipe is 1,5 or 2,0 mm?
1.5s
Sorry 2s
Perfect
Mantap sekali
Absolut brutal 😮
Berapa settingan aliran gas yg didalam tabung,apakah sama?
Super !!!
you got robotic arm, i dont understand how you Can hold gun at handle and so far from weld and repeat the same movemt, i have to hold gun almost at the nozzle and arm must be supported
Have the same problem, here. I *have* to prop, usually need to sit down, and even then the results are often less good.
He has a secret : don't drink alcohol and cofee. It's a Welding Kung-Fu training
@@CottonEyeJoe_001 I drink neither of those.
Then again, I’ve been *extremely* clumsy my entire life, am significantly disabled, am getting on in years, have less-good health - and most importantly of all, by far - *I do not weld for a living.*
A lot of this level of skill boils down to doing it a great deal for a *very* long time. I know it has worked that way with a number of things in my life.
@@CottonEyeJoe_001 my welding kung-fu is a lot of alcohol and amphetamine...
Walking cup is something I haven't got into. It's quite impressive technique. I usually have to prop and secure my other hand near which I can lean into to get decent results. Otherwise my hand shakes way too much. Then again I don't weld that much at work.
我覺得用滴料，會比較快😁😁
¿parameters? clare please.
rest of the video genial
No has visto el amperaje, preflujo, postflujo y rampas de subida y bajada? Si no entiendes ni la máquina que parámetros preguntas?
Muito bom mestre.
Merci pour le video
Best yet….
OMG, That music makes me feel like taking a Xanax!
Y-a-t-il un bon remplissage à l'intérieur? Curieux de voir car dans l'industrie des breuvages, il faut éviter toute contamination potentielle causé par des interstices.
Wonder what kind of Tungsten he likes? Lanthanated? Thoriated? E3/rare earth mix?
I find thoriated produces the cleanest passes on thin wall sanitary tubing. Tried the E3 but always seemed to be a dirtier weld.
Hi sir tack how to put mechine setting please telme
this is whitout GAS?
Am from Ghana 🇬🇭 I also do the same work any help boss 😢
Good practice
nочему на 1 мм трубу такой большой ток 38 А? Я даю 25 если без nрисадки, 32 если с nрисадкой 1,2 мм?
Фиксированной силы тока не будет. Возможно ток будет меняться в зависимости от ситуации.
@@weldHAGOJIBI возможно я варю ,,рисованием", а вы ,,катанием" - расстояние от электрода больше и nотому нужно более высокий ток?
Super bom la explicacao
that seems excessive heat input, the beam is no longer stainless isn't it?
电流开大到50至60之间，不用摇-可以焊的更快又好。
Nst ad300ds и остальные ваши аппараты где их можно найти купить и ознакомиться?
Que tipo de máquina tig es dame el modelo por favor
최고입니다👍
poca corriente.. normalmente a 50Amp. dependiendo de la velocidad.
Where can i get it
Please show how you eliminate the pit hole inside the pipe where you finish the weld.
Weld over long enough and have quite long downslope time. That usually helps.
Eres un máquina
Excelente.! 🥇
Excelente,
Qual máquina é essa
Спасибо!!!
I'm interested
Я варю такие трубы на 55 ампер))
سلام من زبان شما بلد نیستم.ببخشید برا اینکه جوش نفوذ داخل لوله نکنه اون شیلینگ که گذاشتید داخل لوله چی بود کامل توضیح دهید
👍🔥
How many amps? I guess 25-30
👍👍
Why didn't you use filler wire?
Because in sanitary applications you want no contamination and with filler wire you have additional risk of contaminating the weld.
@@martinbank_ I weld sanitary tubing all day and always use filler (usually 1,0mm or 1,2mm). As long as the wire is clean and you keep it in the argon envelope around the cup it’s fine.
I’ve never had a problem with tested sections.
Never
Короче надо двигать как стриптизерша попой виляет тогда получится красивый шов. 👍😁
muito bom ficou top
ООО сан тех труба из нержавейки круто, у нас таких нет только гнилая сталь