ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
ฝัง
- เผยแพร่เมื่อ 6 เม.ย. 2020
- This video shows how to remove the interior door panel (aka: door card) on a 1999-2005 (NB) Mazda MX-5 / Eunos Roadster.
Tools 🛠 required:
-Small flat head screwdriver.
-Phillips #2 screwdriver.
-Phillips #3 screwdriver.
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing. New videos every week*
Disclaimer:
Due to factors beyond the control of MiataMan, I cannot guarantee against improper use or unauthorized modifications of this information. MiataMan assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. MiataMan recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of MiataMan, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not MiataMan.
I have a 1999 Miata and have watched many TH-cams about removing the door panel. Most of the vids I saw showed a second screw in the handle assembly. Mine only had one showing. This vid hits the nail on the head with the second screw hidden under a piece of velcro inside the handle that I did not know was even there. Today, I peeled the velcro back and Voila, there was the hidden screw! Thanks so much! I was going nuts looking for a second screw visible. BRAVO!
Perfect video. Short, sweet and no BS
thank you for a clear and simple video! followed along while I removed my 03 nb door panel
You’re awesome for this! Even I’m a mechanic and could figure it out on my own it is always much faster watching someone do it first
Exactly Chris!
No need to waste time with a little homework, and avoid the the wrath of the Brittle Plastic gods(VW/VAG are the worst!)😎
I really appreciate you showing the clips up close because I am currently trying to buy a few more on Amazon and there are so many sets that have multiple types and I wanted to know what I need to look for. Thanks!
Excellent video...steady camera, clear audio and good explanation...Thanks!! I have to lube the window tracks on my 2000 LS.
Thank you.
Was planning to add a sound deadening mat to my door, you make it seem really easy now.
It's been 3 years but did you install the deadening? I wondered where the best place would be to glue it on :)
@@R-SXX no I haven't yet ☹️
@@R-SXX I have done it on two 99 miatas, I used Dynamat, basically I tried to cover as much area on the inside portion of the outter door skin and also used some around the speaker hole. Speaking of I always use the Rockford Fosgate 8in mids in the door with 1in tweeters. I use a footwell Rockford Fosgate 8in sub in a footwell box for the passenger side. I put my two power amps in the trunk and its a rockin bad ass sound system
Cool video and super nice explanation! Ty❤❤
Thanks for very well explained and helpful video !
Perfect thanks. One screw on my handle was in a different place and just in a hole at the bottom of the handle and not under that piece of felt you lifted up but apart from that my '04 NB Arctic was identical.
Thankyou a very good and clear video.
You are welcome!
Thanks MM. I have manual window cranks so I've got to find the right way to remove those before lifting up the door card.
I'm lucky b/c the guy across the street from me is an upholsterer. Lent me a pry wrench and some picks and I got it off. Now, I have to see if I can get into the metal from behind to work out some dents, lube the mechanism, and install some Hush Mat.
Thank you for this... exactly what I was looking for to fixed an indented part of the door panel.
Thank you, just what I was looking for. Need to replace speaker in my 1999.
Clear and concise, thankyou ❤
Thank you so much for the tutorial I have a problem with the side windows ,slow to wind up and down
Thank you for the video! Very much appreciated!
Great video, in FL second long screw is in a little different place, but it's not hard to find anyway ;)
Thanks. Clear and easy to understand. 🙏
Excellent description.
Very good video man, thank you. 🤘
Great video, thank you very much!
Thanks for the reminder of how to do this. I need to take my driver's one off to make may for a flat door card so I stop hitting my elbow on the handle/armrest in tight turns. You got any tips about doing that?
you've got a nice voice
V helpful. Thanks
It kept the job simply with minimal breakages, only one plastic clip didn't survive :)
Do you have a video of how to remove the door from the car?
Not yet, but I will try to make one soon. Thanks for the suggestion.
Great video!
Does the door have to be removed from the car in order to do this? I have to replace my power mirror and if I don’t have to remove the door that would be a blessing lol
The door does NOT need to be removed. 👍
I just happened to have one in the garage to use as an example.
When I close my door it definitely sounds like an older car door closing (rattley?). Is this because things are loose? Is there a way to fix this?
Sometimes, the back roller that is attached to the window becomes loose and rattled around.
It would be a great idea to remove the window and tighten everything up.
Good time to lubricate the mechanism too.
Do You have Miata Gen 3 NC videos?
Not yet, but I will try to make some in 2023. 👍
@@MiataMan Thanks, happy holidays