Hey bro i changed the water pump on my a4 b8 2.0t quattro and flushed everything, put new coolant in and i changed my cooling fan control module, now its all back together and my radiator stays cool even after running awhile, i got blazing hot heat inside the cab i just think its not circulating through the radiator? Is that make sense? I need some help and not the dealers, i used the oem radiator filll kit that uses the air compressor to create a vacuum to fill the system, any help would be greatly appreciated.
Still using these videos Naptown! My son and I changed his entire engine on his 2009 with your videos. I'm not a mecanic, I'm in software, but learned so much from you. Thank you once again for the tips and tricks.
I changed the original water pump on my 2013 VW 2.0 TSI CC. I watched your videos. The VW was a little trickier than the Audi. The hardest thing was getting the charge pipe off of the throttle body and removing the throttle body bolts. There are two Copland lines that come from the passenger side of the engine remove those first, it gives more access to the throttle body bolts. I used the Graf aluminum water pump. Seems to have stopped the leak. Thanks for your videos they are very useful and entertaining.
Just what I needed to see. I replaced mine today and was abit unsure of the belt as it wasn't hugely tensioned. But your video I can see the belt is easy to deflect like mine so at least I know its all correct
so question was your coolant temp sensor on the waterpump or was it in a different place. I have a 2011 audi a5 with some a4 parts installed and im thinking its my coolant temp sensor thats causing my radiator fans not to spin when the ac is on. its either that or the fan motors died out. I already replaced the 60a fuse in the centeral terminal checked the fuses in the panels and replace the fan control module and still nothing.
I'm done with VWAG/Audi. Plastic cooling systems, plastic oil pans, plastic everything. I like metal much more. Remember metal? It lasted through the life of the vehicle.
Ok now I am confused. I saw another vid showing thermostat replacement. Not water pump. I have 2007 2.0 ( b7) My car temp is running very cool. Very low heat on the heater. I have had mil engine temp codes. Any advice is appreciated
This video was very helpful when I did the water pump 8 months ago but now I’m having issues with the coolant temp sensor not operating.. temp on gauge won’t read and fan always on. I replaced the temp sensor and everything was fine until the next day after a 90 mile drive it failed again and back to the same symptoms.. can it be that the temp sensor from o’reillys auto parts suck?
Hi i recently did a pretty big 2.0t tsi vw rebuild and im left with a small metal peice smaller then a penny. It looks like the bit keeper on a drill but with out the teeth to move it foward trying to figure out how to upload a photo
I was actually hoping you would show the removal of the temperature sensor. I am having a fan problem that does not come on it starts to come on but does not actually come on it spins around a couple times and then stops if I apply current directly the fan runs fine. So I need to replace the temperature sensor preferably without pulling the whole pump out and the intake and pulling the engine out and so on and so forth that means I have to know exactly how it becomes disconnected and pops out
Any recommendations on what milage should you be looking to replace this water pump? Also would you advise replacing with the all aluminum upgrade for longer service life? Thank you Naptown turner
Hi, I am currently working on a 2011 audi a5 that has overheating issue. I took apart the water pump to inspect and noticed the balance shaft that drives the belt for the pump is not moving. Basically the pump is fine, but that shaft does not turn when the engine turns over. Any idea what part I need to replace to fix this? Thanks.
So I got a leak somewhere cant see it leaking leaks alot all I see if it leaking down the oil pan on drivers side coming from up top somewhere oil pump was put on 1000 miles ago back of engine where coolant flange is seems dry nothing on trans any ideas coolant comes to front of oil pan
Hi. Nice video. I have a question? how do you bleed the air out from the sistem after you change this pump. The car do this automaticaly or you have to do something else. Thanks ;)
Hey bro i changed the water pump on my a4 b8 2.0t quattro and flushed everything, put new coolant in and i changed my cooling fan control module, now its all back together and my radiator stays cool even after running awhile, i got blazing hot heat inside the cab i just think its not circulating through the radiator? Is that make sense? I need some help and not the dealers, i used the oem radiator filll kit that uses the air compressor to create a vacuum to fill the system, any help would be greatly appreciated.
Exactly what I needed to see my 2.0 is setting a cooling performance code, so I figure I need to replace that whole module since the t-stat is in there. Do you have a opinion on the upgraded aluminum water pump modules? I am not so sure I could l do that with the intake still bolted up though. Maybe I will look into taking it off and doing some carbon cleaning.
Thomas Hoyt here is the intake video, th-cam.com/video/kR8zLHJVrNY/w-d-xo.html valve cleaning helps but I don’t typically do it unless there is an issue. Only needed to do it like 10 times in 9 years on this engine but I prefer to just do a rebuilt cylinder head on a car I plan to keep. No experience with the aluminum water pump someone had a cast-iron water pump and it didn’t fit right had to replace it. In this video when I show the other engine with the balance shafts look at that water pump.. there is a aluminum piece in the updated water pump and it looks like that.
I explained in this video that I’m showing it so you can get the best view outside the car.. and that you should do it with the intake still installed.
Just changed my pump it is leaking from the small nipple that connects to the small heat exchanger. I even replaced the o-rings with new ones. Any ideas?
I have a 2013 VW CC Sport with the 2.0 TSI engine, is it possible to change the water pump without having to remove the intake manifold, since it is a transverse engine? doesn’t seem to be as much room as in the Audi’s.
i did one a few ago on a 2013 vw golf gti did it without removing intake manifold. was a pain in the arse but doable. take the throttle body off. the audi intake manifolds look much easier ti take manifolds off tho
The wires to the coolant temp sensor pulled out of the plug on a 2008passat 2.0t and don’t know wihich wire goes where on the plug or doesn’t it matter?
That’s why I save old wire harnesses, I don’t know for sure if it matters but I’d put it back the way it was. Sometimes you can take the plug apart and find enough evidence of the old wires to put it back together
The wires pulled right out of the plug so there was nothing to go by, I replaced the water pump and now a few seconds after starting the car both fans turn on full force. I went by your video and it was a great help, I dint replace the coolant temp sensor and tried wiring both ways and fans still run full speed. Nothing was wrong except for a leak prior to replacing. Any help would be great
Go to your local junkyard and chop off the connector and butsplice connect it. Even if you get it right it’s going to take about 10min unless you clear the faults
Already been to the two in my area but didn’t have anything but I was able to get the right plug just wasnt to the sensor, it’s been one of those projects where if it can go wrong it did including someone else previously worked on the car and I had to put things back the way they should have been. I appreciate what you do and your videos, best ones out there that I’ve found. Thank you, somehow I’ll figure it out on my own.
I finally figured out what was causing the fans to start up justAfter starting the car. The plug I got to replace the one that was on the car must have been corroded or something inside the pin, check for continuity and one side was dead so luckily while at the junk yard I grabbed a couple and switched it out, now runs like a top again, thank you for the help it was enough to get me to think and figure it out, except for all the if it could go wrong it did your video and instruction made things easy.
I just pulled mine apart, realized the small pulley is broken which is why it wasnt cooling the engine, how hard is it to put a new pulley back? Pls help!
Be honest, you broke it didn’t you? If it broke itself for some crazy reason I would feel it necessary to remove the entire intake balance shaft for inspection. If you broke it trying to remove it you’re gonna still have a bad time but it might spin out with a right angle pick (reverse thread)
I paid some dummy ti change my thermostat. Housing and i think he porbably put it on wrong and it popped after 3 months or so, is there a vid i can follow of you dismounting the intake etc?
I was able to take the belt off, i have it in my hands, i want to know what i have to do to put in a new one, i might have to change the whole waterpump anyways, bc there was a coolant leak and it looked like it was coming from the waterpump, i did not do a preasure test before taking it out so i dnt know exactly where the leak was coming from, it honesty looked like it was coming from the water pump area, and i assumed it was the water pump, also my car kinda overheated bc i saw the needle go to the high side...
Thermostat is Contained in the water pump housing and is usually all replaced as a single unit. Read the description on your new pump when ordering to make sure it says includes thermostat
My friend u need to learn more coz out side engine nd u strugling what abt if the engine in side the car i dont think so u gona do that waterpump , u can fit without belt waterpump first, tight the waterpump bolt , then after put the belt on waterpump gear nd turn the creankshaft pully anticlock wise !!
![How to Fix AUDI P2181 Engine Code in 4 Minutes [3 DIY Methods / Only $7.36]](http://i.ytimg.com/vi/xkmSTtgRf88/mqdefault.jpg)
Replacing in the car th-cam.com/video/K3TfykE4uFo/w-d-xo.html
Hey bro i changed the water pump on my a4 b8 2.0t quattro and flushed everything, put new coolant in and i changed my cooling fan control module, now its all back together and my radiator stays cool even after running awhile, i got blazing hot heat inside the cab i just think its not circulating through the radiator? Is that make sense? I need some help and not the dealers, i used the oem radiator filll kit that uses the air compressor to create a vacuum to fill the system, any help would be greatly appreciated.
Still using these videos Naptown! My son and I changed his entire engine on his 2009 with your videos. I'm not a mecanic, I'm in software, but learned so much from you. Thank you once again for the tips and tricks.
I changed the original water pump on my 2013 VW 2.0 TSI CC. I watched your videos. The VW was a little trickier than the Audi. The hardest thing was getting the charge pipe off of the throttle body and removing the throttle body bolts. There are two Copland lines that come from the passenger side of the engine remove those first, it gives more access to the throttle body bolts. I used the Graf aluminum water pump. Seems to have stopped the leak. Thanks for your videos they are very useful and entertaining.
Grafs are good pumps. I assume you purchased the all aluminum pump module.
Thank you for your videos! Just did my timing chain. Water pump is next!
Just what I needed to see.
I replaced mine today and was abit unsure of the belt as it wasn't hugely tensioned. But your video I can see the belt is easy to deflect like mine so at least I know its all correct
You have no idea how much you’ve helped me as I build my a4 b8 to 600 hp slowly . Thanks so much man much love !
so question was your coolant temp sensor on the waterpump or was it in a different place. I have a 2011 audi a5 with some a4 parts installed and im thinking its my coolant temp sensor thats causing my radiator fans not to spin when the ac is on. its either that or the fan motors died out. I already replaced the 60a fuse in the centeral terminal checked the fuses in the panels and replace the fan control module and still nothing.
what'd you replace to achieve that?
Your the man when it’s comes to the A4❕❕❕❕❕❕❕ Thanks for all the help always
Very helpful seeing this view without all the wires, etc. Thanks! Unfortunately, looks like I'll be replacing mine.
dude youre my favorite youtuber 🤣keepin my car runnin
Keep up the good work these videos are very helpful
Id like to add, whenever that union or any plastic material turns brown in color, replace it. The plastic is deteriorated and brittle.
Great video, SUPER helpful!!!
great video thanks alot! so much easier to see whats going on, with the engine out.
Thanks for teaching us 🙏!!
Got my sub for schooling straight to the point
Excellent video, good job and thank you sir
Good job - Thanks for the tricks !
like always great videos Thanks !
dude i wish you lived in my area. i would def be kickin it at your garage with my A5
you sound like someone I would trust.
I use a touch of Henkel Red rubber grease on all the electrical plugs & O rings, It makes the job so much easier for then on.
Just pull out a 2010 very easy with your vids
Thank you so much ❤️
Da Best bro thanks
I'm done with VWAG/Audi. Plastic cooling systems, plastic oil pans, plastic everything.
I like metal much more. Remember metal? It lasted through the life of the vehicle.
Gotta cut down on the cost of the vehicle somehow.
Thanks!
Super organized Video.......N O T!!!!!!
It was one of the first videos I ever made but thanks for watching
Ok now I am confused. I saw another vid showing thermostat replacement. Not water pump.
I have 2007 2.0 ( b7)
My car temp is running very cool. Very low heat on the heater. I have had mil engine temp codes. Any advice is appreciated
This video was very helpful when I did the water pump 8 months ago but now I’m having issues with the coolant temp sensor not operating.. temp on gauge won’t read and fan always on. I replaced the temp sensor and everything was fine until the next day after a 90 mile drive it failed again and back to the same symptoms.. can it be that the temp sensor from o’reillys auto parts suck?
Hi i recently did a pretty big 2.0t tsi vw rebuild and im left with a small metal peice smaller then a penny. It looks like the bit keeper on a drill but with out the teeth to move it foward trying to figure out how to upload a photo
I was actually hoping you would show the removal of the temperature sensor. I am having a fan problem that does not come on it starts to come on but does not actually come on it spins around a couple times and then stops if I apply current directly the fan runs fine. So I need to replace the temperature sensor preferably without pulling the whole pump out and the intake and pulling the engine out and so on and so forth that means I have to know exactly how it becomes disconnected and pops out
Hey do you have a link to the o ring replacement on that “pipe” thanks
Any recommendations on what milage should you be looking to replace this water pump? Also would you advise replacing with the all aluminum upgrade for longer service life? Thank you Naptown turner
Been told it's really the o ring that fails,not the actual assembly
It’s Good I like👍🏽💪🏽
Hi, I am currently working on a 2011 audi a5 that has overheating issue. I took apart the water pump to inspect and noticed the balance shaft that drives the belt for the pump is not moving. Basically the pump is fine, but that shaft does not turn when the engine turns over. Any idea what part I need to replace to fix this? Thanks.
So I got a leak somewhere cant see it leaking leaks alot all I see if it leaking down the oil pan on drivers side coming from up top somewhere oil pump was put on 1000 miles ago back of engine where coolant flange is seems dry nothing on trans any ideas coolant comes to front of oil pan
Hi. Nice video. I have a question? how do you bleed the air out from the sistem after you change this pump. The car do this automaticaly or you have to do something else. Thanks ;)
Got my water pump changed with timing change ...my a43.0 came back missing and plugs didn't help...what's wrong with my car now
Hey bro i changed the water pump on my a4 b8 2.0t quattro and flushed everything, put new coolant in and i changed my cooling fan control module, now its all back together and my radiator stays cool even after running awhile, i got blazing hot heat inside the cab i just think its not circulating through the radiator? Is that make sense? I need some help and not the dealers, i used the oem radiator filll kit that uses the air compressor to create a vacuum to fill the system, any help would be greatly appreciated.
How tight do all theese water pump bolts need to be?
6:45 What is the name or part number of that spool piece? Thanks.
I need a 2012 A6 white front passenger fender naptown can you help?
Great videos! Do you think I can replace just the thermostat w/o removing the water pump? Anyone have any luck doing that?
Exactly what I needed to see my 2.0 is setting a cooling performance code, so I figure I need to replace that whole module since the t-stat is in there. Do you have a opinion on the upgraded aluminum water pump modules? I am not so sure I could l do that with the intake still bolted up though. Maybe I will look into taking it off and doing some carbon cleaning.
Thomas Hoyt here is the intake video, th-cam.com/video/kR8zLHJVrNY/w-d-xo.html
valve cleaning helps but I don’t typically do it unless there is an issue. Only needed to do it like 10 times in 9 years on this engine but I prefer to just do a rebuilt cylinder head on a car I plan to keep. No experience with the aluminum water pump someone had a cast-iron water pump and it didn’t fit right had to replace it. In this video when I show the other engine with the balance shafts look at that water pump.. there is a aluminum piece in the updated water pump and it looks like that.
You can remove waterpump without removing intake
I explained in this video that I’m showing it so you can get the best view outside the car.. and that you should do it with the intake still installed.
Do you have to remove the car from the engine to change the water pump?
@@isackhernandez3691 I hope that’s not a serious question
Just changed my pump it is leaking from the small nipple that connects to the small heat exchanger. I even replaced the o-rings with new ones. Any ideas?
did you replace the plastic nipple bit that the orings go on to aswell?
otherwise its probably rolled the oring off or nicked it
I have a 2013 VW CC Sport with the 2.0 TSI engine, is it possible to change the water pump without having to remove the intake manifold, since it is a transverse engine? doesn’t seem to be as much room as in the Audi’s.
i did one a few ago on a 2013 vw golf gti
did it without removing intake manifold.
was a pain in the arse but doable.
take the throttle body off.
the audi intake manifolds look much easier ti take manifolds off tho
Hi, do you have to do any timing when fitting the belt on the water pump?
Nope. The balance shaft is timed (of course), but the water pump toothed belt is not.
Do we need to remove the waterpump to replace the temp sensor?
❤❤❤
How to properly bleed cooling system after water pump replacement?
What is the belt called under the cover?
What type of tool is used for taking off the water pump belt screw ?
T30 torx bit
I just wanted to know how to replace the thermostat
Helloo, i need to remove the water pump to remove the engine oil cooler?
yes
So where's the thermostat at ? Location.?
The other plastic cover below the water pump, what is that called I think mine is leaking as well and I can't find the name to identify it.
Blowby chamber case / cover - gasket
My man
All good to re-use the bolts?
You can but its better to use new ones. it could start leaking
How much is the cost .on work like.this.
You force f'd that thing the whole way wow
Is this part 3 of the engine take-out?
No.. th-cam.com/video/HdmUf-3Mf5g/w-d-xo.html
@NaptownTuner Sh!t sorry man, meant part 4. I've seen all three parts at least three times now. Maybe put it in a playlist for us dummies?😎
The wires to the coolant temp sensor pulled out of the plug on a 2008passat 2.0t and don’t know wihich wire goes where on the plug or doesn’t it matter?
That’s why I save old wire harnesses, I don’t know for sure if it matters but I’d put it back the way it was. Sometimes you can take the plug apart and find enough evidence of the old wires to put it back together
The wires pulled right out of the plug so there was nothing to go by, I replaced the water pump and now a few seconds after starting the car both fans turn on full force. I went by your video and it was a great help, I dint replace the coolant temp sensor and tried wiring both ways and fans still run full speed. Nothing was wrong except for a leak prior to replacing. Any help would be great
Go to your local junkyard and chop off the connector and butsplice connect it. Even if you get it right it’s going to take about 10min unless you clear the faults
Already been to the two in my area but didn’t have anything but I was able to get the right plug just wasnt to the sensor, it’s been one of those projects where if it can go wrong it did including someone else previously worked on the car and I had to put things back the way they should have been. I appreciate what you do and your videos, best ones out there that I’ve found. Thank you, somehow I’ll figure it out on my own.
I finally figured out what was causing the fans to start up justAfter starting the car. The plug I got to replace the one that was on the car must have been corroded or something inside the pin, check for continuity and one side was dead so luckily while at the junk yard I grabbed a couple and switched it out, now runs like a top again, thank you for the help it was enough to get me to think and figure it out, except for all the if it could go wrong it did your video and instruction made things easy.
I just pulled mine apart, realized the small pulley is broken which is why it wasnt cooling the engine, how hard is it to put a new pulley back? Pls help!
Be honest, you broke it didn’t you? If it broke itself for some crazy reason I would feel it necessary to remove the entire intake balance shaft for inspection. If you broke it trying to remove it you’re gonna still have a bad time but it might spin out with a right angle pick (reverse thread)
I paid some dummy ti change my thermostat. Housing and i think he porbably put it on wrong and it popped after 3 months or so, is there a vid i can follow of you dismounting the intake etc?
@@jimmytejada9480 search NaptownTuner 8min intake removal I have a couple though
I was able to take the belt off, i have it in my hands, i want to know what i have to do to put in a new one, i might have to change the whole waterpump anyways, bc there was a coolant leak and it looked like it was coming from the waterpump, i did not do a preasure test before taking it out so i dnt know exactly where the leak was coming from, it honesty looked like it was coming from the water pump area, and i assumed it was the water pump, also my car kinda overheated bc i saw the needle go to the high side...
i use silicon too ...
Where is the auxillary coolant pump?
What do you think about the water pumps off Amazon there $60
Get the aluminum one m8
@@davidescobedo1317 that is the one I put on
@@MMRSCRAPIRE Graf unit? Did you re-use bolts?
@@JH-sc7cs yes I got the aluminum one off of Amazon and it seems to be working just fine
@@MMRSCRAPIRE Ok cool, doing my install this morning with the Graf unit re-using the bolts
Where is tiguan engine oil temperature sensor location 2.o tsi 2013
Very harder when engine in car
What about the thermostat?
Thermostat is built into the waterpump
Where is the thermostat?
Thermostat is Contained in the water pump housing and is usually all replaced as a single unit. Read the description on your new pump when ordering to make sure it says includes thermostat
@@jayscheck thanks. Mine came with new thermostat and sensor
My friend u need to learn more coz out side engine nd u strugling what abt if the engine in side the car i dont think so u gona do that waterpump , u can fit without belt waterpump first, tight the waterpump bolt , then after put the belt on waterpump gear nd turn the creankshaft pully anticlock wise !!
th-cam.com/video/K3TfykE4uFo/w-d-xo.html
Warranty time is about 3.5hrs most shops charge up to 5hrs for this
Tanx alot for the video it was very helpful
you broke the cheap german plastic
Better views on this one th-cam.com/video/vla7dUINoBo/w-d-xo.html
Ii