This video helped me out so much with getting my shadow cranks onto my fixed gear. So much appreciated. Just a little thing to make lining that spacer up a bit easier because it was annoying the hell out of me. Instead of using your pinky finger to hold it up inside the BB, you can take a long screwdriver or something like that and thread it through your bb and spacers. Screw on the second piece with the screwdriver holding the spacer suspended in the middle. Then when you are almost at finger tight, when the spacer is being held in by a light pressure, fully align it. Tighten and you're done.
I've found that best chainline happens when you dont run the provided bottom bracket inside spacer that hugs the sprocket so it can press closer to the frame. Just some washers instead
I had a bmx crank on my fixie, and it made it super slow and feel way too heavy.. Whats up with that. Also, where did you get your handle bars and what are they.
look at this man blessing us with the knowledge even though hes recovering😍
Informative, good production quality, Sick af. good stuff bro.
This video helped me out so much with getting my shadow cranks onto my fixed gear. So much appreciated.
Just a little thing to make lining that spacer up a bit easier because it was annoying the hell out of me. Instead of using your pinky finger to hold it up inside the BB, you can take a long screwdriver or something like that and thread it through your bb and spacers. Screw on the second piece with the screwdriver holding the spacer suspended in the middle. Then when you are almost at finger tight, when the spacer is being held in by a light pressure, fully align it. Tighten and you're done.
This video meets my demand! I was just thinking about how I wanted to install a bmx crank.
I’m just in the process of planing out a freestyle fixie. This is godsent.
He’s right I can tell you all about it
apart from being super helpful, video is just pleasant to watch. good stuff.
Glad you enjoyed 🙏
Just switched my Courttek over to BMX cranks today. Thank you 🤝
cant wait to see you riding againt get well sooon.
Just for the record: You can put a Euro style BMX BB into a BSA frame, because the two are one and the same standard?
I have a question, I have the exact same resist cranks as you but mine can be easily pressed in to the spindle, does it mean its worn out almost? thx!
chill instructions bro def dope bro
Any recommendations for new bottom bracket for replacing the stock bottom bracket on a redline mx24?
Red loctite would probably help if using a spider.
I would have inserted the spindle before tightening to help with alignment.
Dope deacon wit the krull yeee speedy recovery ❤️🩹 on the knee
Man, need this set up
I’m trying to do this with primo cranks on my ryd masher idk where to start
those cranks.... so nice
How do you remove the cranks without the extraction threads without using a hammer (asking for a friend)
Have you run into any issues with chainline since most fixed gear hubs are 120mm compared to bmx 110mm?
I've found that best chainline happens when you dont run the provided bottom bracket inside spacer that hugs the sprocket so it can press closer to the frame. Just some washers instead
Love the Duke man!!!!!
Can Omnium Cranks be installed on a Master Bike Co frame?
U got to make a video using masterbikeco's huv and 10mm adapter! Build a sick ass rear wheel running on a microdrive but on a tarck
(Just what i did on my cyclone lol)
i dig the melee sounds
Fellow person of culture
You should give some links for those bbs
what handlebars are those?
duude why no build with masterbike's rear hub ?? use that sick ass 10mm axle converter and stick a microdrive in !
did that on my courttek, left side drive
ye wickest wheel build @@leanlobster69
I had a bmx crank on my fixie, and it made it super slow and feel way too heavy.. Whats up with that. Also, where did you get your handle bars and what are they.
Did you gear down the rear cog? Your ration would be way off it you dropped to a 33 in front and still had a 17 in the rear
I peep the resist cranks👁👁
I clicked the thumbnail becouse I thought it said RACIST on the crank arm. Dyslexia strikes again 😑
Devin GOd🙏🏽😎
Doocaaaannn🔥🔥
Lubricant seen 😂
Looks like u was trying so hard not to LOL
This man's beanie angle is just straight offensive.
I actually use bolt drive on my fixed gear. No issues whatsoever so far.