Power Wheels First Gear Delete
ฝัง
- เผยแพร่เมื่อ 21 ธ.ค. 2023
- How to gain the most speed out of your power wheel car! Modify at your own risk! This is for drag racing purposes only!
We run a power wheels drag racing group in Oxford pa known as “ oxford power wheels racing” check us out on Facebook!
We hope this helps you guys get that top speed that you are looking for! Check back at our precious videos on how to set up the Kelly speed controller!
This is a must have for a outlaw racer in power wheels
Stay tuned, like, subscribe and stay fast!
#howto #modifiedpowerwheels #fastkidsclub #powerwheels #dragracing #modified #teterbuilt #eatsleeprace
I am so grateful to stumble upon this- you will save me so many headaches!
🙌🙌🙌🙌🙌
How do you go about marking the bolt holes?
I feel so many things can go wrong attempting this mod, make sure you have a spare gearbox housing.
You have to take your time with it, do a little measuring so you get it right the first time!
Good video !
Are you familiar with dual motor gearbox setup?
😉😉😉😉
Your killing me smalls. Jk. If i get all this done and figured out and we go down there in the south side, indiana and my son straight gaps everyone. im just going to say you did it. You caused me to just go all out! Lol😂😂😂 i have everything, but pinion gears and a connector for the controller for the computer. If you do a first gear delete, does that mean the pinion gear changes?
Also, I just ordered a dc power supply to break in the redlines.
Could have had rear disk brakes for the rwd cavalier im building with the funds im putting in my sons porsche. All fun! i love it! For the kiddos!
😂😂😂 doing the first gear delete, you will have to figure out the right pinion size for your setup depending what you want! Smaller size more torque , bigger pinion , more top end.
A little bit of trial and error will give you the best setup!
Break in the motors on 6v then 12v and they should be good for awhile! That’s what we do
Any suggestions on where to start as far as pinion size for 50 lb kids in 2 seater mustangs? Stang wheels with harbor freight mat rears like your video, 20v tool batteries, adjustable motor control and 775s. Only asking bc my motors didn’t come with pinions and idk what to buy 😂😂 thanks for the vids
I would do 13 or 14T start there, with the ESC it detects load on the launch so you don’t want to have to tell of a pinion or it’ll bog really hard , we ran 12s on my sons lambo and it did 2.80s in the 60 foot
It will be a little trial and error with pinion sizes , order a few different ones and just play with it
@@TrevorsFastLife and that’s 14/15T with the first gear delete? Thanks!
@@scottf8136 yes sir!
What pitch? My Thunder 24v UTV measures to a 20dp, not 32, like the 7R gearboxes evidently have.
first
💪🏻
Hey brother! I'm starting a racing group in my town. How can I get connected with other racing chapters
Shoot me an email! @
Oxfordpowerwheelsracing@gmail.com
Im considering doing this for my daughters 20v dale car with c7 power wheels wiring that ill be building for drag racing it has 550motors on will it be good or should i put 775 motors and also her 20v "drift" corvette do you think it will kill the low end torque and prevent her from spinning by doing this mod or will it be better?
Make sure you redo all the wiring with 10 guage and use a 100amp or more breaker, it’s to much of a load on a stock shifter switch and wiring
It’ll be fine for drifting still it’ll give it a lot more mph
550s or 775s will work
Awesome thanks! Love watching your content🤟 i also messaged you on fb for details on the power wheels drag racing rules and different classes ..do you have a sheet of the rules, restrictions ect somewhere just so i have ideas where to start and how to split classes i think about doing like stock 12v, modified 12v 18v 24v..i would love to organize something like this for the kids and parents near me (ontario canada) at carshows, local events... i dont plan to go as big as you guys for now but love the way your all organized thanks in advance
Been doing this since 2017, but always used an aluminum plate to hold two 775 motors on the back; the plate solidly locates the motors and stiffens up the gearbox case. I have several vehicles that are still running the original motors several years later but have also broken gearboxes in half with the resulting torque... I would be worried about your setup's durability under hard use-- you've blocked the motor's cooling intake holes and the thin plastic you're mounting to is not very strong (the normal mounting point is pretty sturdy). Has it held up fairly well?
Def agree
How much would you charge for a couple modded boxes?
I have 1/8 aluminum plate on the backs of the gear boxes, before like the video it was just plastic , but believe it or not we never had an issue that way! But I knew I needed to stiffen it up once we did a dual motor setup , it’s nice and solid now with the 1/8” plate, no gears breaking, and faster than he’s ever gone!!
We use our setups for drag racing only
So you can run any tooth pinion gear as long as the mesh is correct?
Correct! But you will need to do some testing to confirm the best pinion size for your setup , it depends what you want , a lot of top end or a lot of torque , more torque smaller pinion, more top end, bigger pinion
@@TrevorsFastLife that's awesome and thank you for the videos and info. My little guy is excited!
@@hopperracing no problem man! Hope to see him flying!
I did a first gear delete and I’m having issues with the battery’s only lasting a minute or 2 on a 12ah battery , is something else the issue ??
Sounds like something is shorting out ,
Make sure you are running 10 guage wiring and get away from the stock shifter switch , only made to handle 30amps