This is EXACTLY what i was looking for. This is the same motor housing type as in the ELECTROLUX VACUUM CLEANER MODEL : ZSH720 . Hoping this will help future people looking for how to service this motor.
Very informative video! Thank you for this. I have one recommendation though. At the end of the video when you pressed the lid back on and glued it; What you should have done was submerged the lid in a bowl of water, microwaved it until the water reach boiling temperature, and then press the lid back on while the lid was still hot. That way, the lid would shrink fit back onto the motor properly, and you wouldn't have needed to use the glue.
My comments are on JJRClassics88: Your suggestion would work for shrunk fit tolerance. May not work in this case, because the lid was easily put on. At the time of removing the lid, it seems to be expanded by sharp screw driver. The removal process of lid is skipped in the video. It is a difficult step.
To anyone watching this video, DO NOT use super glue !! USE Silicon in 1-2inch sections around the round dish part, let dry for a day...now you can cut through it next time around.
Don't insert screwdriver into aluminum fan to hold it when trying to remove the bolt. You can damage it/bend the blades and it will make a lot of noise and cause the motor to overheat. There are other methods. I learned this the hardway.
@@inderjitwassi1420 You take two thin scraps of wood that fit into brush end of the motor, measure the rotor brush size, clap these two pieces of wood and drill a hole the same size as the brush, attach these two wood pieces to the rotor/ brush area/clamp so that when you want to unsrcrew the bolt rotor does not spin.
So youd rather damage the commutator on the motor rather than put a small dent in the impeller,, just hush.., youre not the genius your momma tells you that u are.. they say that cuz they love ya.. lol. Sorry. Sounded funnier in my head and less like a dick..
Beware of LEFT hand threaded nuts at some motor models. It seems that the motor on this video has a right hand threaded nut. For example, the VCM-K30HU has a LH threaded M6.
Hi, thanks for your excellent video! I want to ask one problem I am facing with my Vacuum cleaner. One day the zip of the dust bag was open and I used the vacuum cleaner in a dusty area and I immediately smelled something wrong. So, I switched off the machine immediately. Then after some days in opened and cleaned the motor of the vacuum cleaner and cleaned all dust and debris. There was no smell of coil getting burnt. I dropped few drops of machine oil on both the bearings. After starting, I could see lots of sparks near the bushes and different smell coming from the machine. Kindly, suggest the probable problem and its solution.
Inspect both brushes for to much wear or to deep of a curve in them, if to much inward curve, the side edges may be to sharp causing a kind of outward glancing, dancing arcing..can take out to deep of inward curve with some delicate surgery with a dremel tool to once again match the original brush curve.
2:15 It's actually better to put the screwdriver between the wings in the inner hole. That produces less force on the metal wings, and bending them won't result in squeak.
Thank you for the video, I have a question, when I’m trying to unscrew the main screw the shaft and the rotor keeps rotating with the wrench, how can I hold the rotor from moving?
This is what i am looking for. Excellent...! But you don't show me how to put cap off. And why should you apply glue just like you wont open it again? Thanks alot anyway
But in this way how is the secret to vacuum cleaners consumes low energy like a EU european energy label and conservates more good suction in the low wattage ones in september 2014 what is the motor is the motor has nano ferrite or is a copper wire and iron? or is something special in the motor thanks
Hello. I am looking for a new nut (which maintains the turbine) because I damaged the original one... Could you confirm that it is a m8 with a pitch of 1.25 and with a left handed thread? Thanks
@@vacuumtests9225 thanks but I meant won't it spoil the motor of the other vacuum you use to clean the motor. For example my motor is full of plaster dust. If I use another vacuum to clean that then it will also become full of plaster dust.
@@inderjitwassi1420 If your motor what you are cleaning is full of plaster dust it shouldn't be too much for your vacuum to handle. Problem comes when you suck up a lot of plaster dust. Bagged vacuums with fabrig bag handle it well, but bagless vacuums really don't like plaster dust.
Thanks for the video! I have problem with my vacuum cleaner motor, that part you took out at 2:43 (UFO shaped) is broken, do you know if it is possible to buy that part anywhere? Or do you know what is it called?
I'm not impressed with your wedging technique to remove and install the nut on the end of the shaft. Bends in the turbine will unbalance it and shorten the life of the motor bearings. I think an investment in a small impact driver will help you not damage your customer's property. Save the wedging for more robust machines like lawnmowers. I personally use a c-clamp on the side of mower decks, by the way.
it's a stupid design because the dirty air goes through the motor and if it starts to smell you can't clean it inside, the cooling airflow should be separate
This poorly ineficiet vacuum motors is na piece of hit consumes much energy for wasting the old vacuums consumes 1000 or 1100w maximum and conservates good suction
How to clean a vacuum cleaner. With another vacuum cleaner.. genius! Shit. Now i gotta go buy another vacuum cleaner which is what i was trying not to do by cleaning the one vacuum.. is where they get ya.
This is EXACTLY what i was looking for. This is the same motor housing type as in the ELECTROLUX VACUUM CLEANER MODEL : ZSH720 . Hoping this will help future people looking for how to service this motor.
Very informative video! Thank you for this.
I have one recommendation though. At the end of the video when you pressed the lid back on and glued it; What you should have done was submerged the lid in a bowl of water, microwaved it until the water reach boiling temperature, and then press the lid back on while the lid was still hot.
That way, the lid would shrink fit back onto the motor properly, and you wouldn't have needed to use the glue.
My comments are on JJRClassics88: Your suggestion would work for shrunk fit tolerance. May not work in this case, because the lid was easily put on. At the time of removing the lid, it seems to be expanded by sharp screw driver. The removal process of lid is skipped in the video. It is a difficult step.
Thank you. Your video gave me the confidence to fix the inbalance of my filthy turbine.
Thank you. I was trying to figure out how to remove the fan cover. You solved it. Thank you again. Cheers!😀
Thanks for the impeller disassembly video. Now I just need to figure out how to remove my motor impeller
I have made a puller that pops open the cover Everytime. Thanks for the insight.
Nice video. My motor also had a lot of cat hair in it but now it is working perfect again. Thank you!
To anyone watching this video, DO NOT use super glue !! USE Silicon in 1-2inch sections around the round dish part, let dry for a day...now you can cut through it next time around.
I know my heart was like nooo why super glue. Now good luck to the next person or even the same person try to repair it next time lol
@@susmitsinghits a fire hasard its not servicing lol superglue is flammable
A tip I used for cleaning dog hair stuck on the vents at min 2.59, I used a small blow-torch to burn off the stuck hair in the vents. WALLA :)
Don't insert screwdriver into aluminum fan to hold it when trying to remove the bolt.
You can damage it/bend the blades and it will make a lot of noise and cause the motor to overheat. There are other methods. I learned this the hardway.
You are right.
I am using srew driver in the middle, while opening the baud to the left in the midle
You say there are other methods - please advise what these are. Thanks
@@inderjitwassi1420 You take two thin scraps of wood that fit into brush end of the motor, measure the rotor brush size, clap these two pieces of wood and drill a hole the same size as the brush, attach these two wood pieces to the rotor/ brush area/clamp so that when you want to unsrcrew the bolt rotor does not spin.
So youd rather damage the commutator on the motor rather than put a small dent in the impeller,, just hush.., youre not the genius your momma tells you that u are.. they say that cuz they love ya.. lol. Sorry. Sounded funnier in my head and less like a dick..
Beware of LEFT hand threaded nuts at some motor models. It seems that the motor on this video has a right hand threaded nut. For example, the VCM-K30HU has a LH threaded M6.
Hi, thanks for your excellent video!
I want to ask one problem I am facing with my Vacuum cleaner. One day the zip of the dust bag was open and I used the vacuum cleaner in a dusty area and I immediately smelled something wrong. So, I switched off the machine immediately. Then after some days in opened and cleaned the motor of the vacuum cleaner and cleaned all dust and debris. There was no smell of coil getting burnt. I dropped few drops of machine oil on both the bearings. After starting, I could see lots of sparks near the bushes and different smell coming from the machine.
Kindly, suggest the probable problem and its solution.
Inspect both brushes for to much wear or to deep of a curve in them, if to much inward curve, the side edges may be to sharp causing a kind of outward glancing, dancing arcing..can take out to deep of inward curve with some delicate surgery with a dremel tool to once again match the original brush curve.
I don't remember what is the correct side of the motor who makes contacts with the metal part of the pcb. Blue or red?
I really don't remember, but it should not matter.
I wish you could show ho2 you took that cap off. I don't know how I'll take the cap of the motor off (the part that you explained at 00:40)
I need to replace the beige plastic part that is broken. Do you know where and what I search (the name)?
You can't buy it separately. You have to buy new motor. These are very cheap motors.
I saw prices, unfortunatelly in my country motors cost 50~60 €. I try to fix it. If I can't, I will buy a new cleaner. Thank you@@vacuumtests9225
I will assemble vacuum later today. All vacuum body parts are washed now. I really hope it works.
2:15 It's actually better to put the screwdriver between the wings in the inner hole. That produces less force on the metal wings, and bending them won't result in squeak.
Outer hole increases leverage/lowers force.
Thanks for sharing! I'll try opening up the turbine in hopes of fixing my own:)
Nice!
Getting the motor tefitted is problem
Thanks for sharing. I love the accent btw.
He's from Finland.
Thank you for the video, I have a question, when I’m trying to unscrew the main screw the shaft and the rotor keeps rotating with the wrench, how can I hold the rotor from moving?
You can use an impact driver so it can give torque to the nut not the shaft
I'm surprised you didn't take the opportunity to apply a little lube to the bearings 🤷♂️🤷♂️🤷♂️
You sound like the guy from the hydraulic press channel!!
That's because guy in the hydraulic press channel is from Finland also.
You sound like the kid that got his self knocked the 🤩uk out for being shallow minded......
Parabéns muito bom este vídeo está limpeza do espirado de pó valeu são Paulo
What would happen if I use a metal clamp/tie like those Hose clamps instead of gluing it?
It might work :)
This is what i am looking for.
Excellent...!
But you don't show me how to put cap off.
And why should you apply glue just like you wont open it again?
Thanks alot anyway
But in this way how is the secret to vacuum cleaners consumes low energy like a EU european energy label and conservates more good suction in the low wattage ones in september 2014 what is the motor is the motor has nano ferrite or is a copper wire and iron? or is something special in the motor thanks
Hello. I am looking for a new nut (which maintains the turbine) because I damaged the original one... Could you confirm that it is a m8 with a pitch of 1.25 and with a left handed thread? Thanks
If you clean the motor with another vacuum as you did, will it not spoil that vacuum's motor?
It won't spoil it. It's actually very good way to clean it :)
@@vacuumtests9225 thanks but I meant won't it spoil the motor of the other vacuum you use to clean the motor. For example my motor is full of plaster dust. If I use another vacuum to clean that then it will also become full of plaster dust.
@@inderjitwassi1420 If your motor what you are cleaning is full of plaster dust it shouldn't be too much for your vacuum to handle. Problem comes when you suck up a lot of plaster dust. Bagged vacuums with fabrig bag handle it well, but bagless vacuums really don't like plaster dust.
Hi. Sir good day! Question how to reverse ? cycle motor 220 vacuam same
Motor like dist video.
How did you open it?
Nice socket wrench screwdriver style! Where did you find that at?
Thank you!
So useful am designing my own
One way job after the glue i hope you don't need to clean it out again.
Unless the vacuum cleaners pre-motor filter fails.
Thanks for the video! I have problem with my vacuum cleaner motor, that part you took out at 2:43 (UFO shaped) is broken, do you know if it is possible to buy that part anywhere? Or do you know what is it called?
Kiitokset ohjeista, nyt on imuri huollettu!
La tuerca que quitas he visto videos que para sacarla hay que girarla en sentido horario. Cómo distingo hacia qué lado debo girar para quitarla?
need a vacuum cleaner to fix a vacuum cleaner
ita like needing a hammer to make a hammer. . . . only dirtier and worse
موتور رو داغون کردی🤗🤗
this was helpful
Nice video.
Are you Hungarian.
Finnish
@@vacuumtests9225 very similar accent.
Genius !!!
I'm not impressed with your wedging technique to remove and install the nut on the end of the shaft. Bends in the turbine will unbalance it and shorten the life of the motor bearings. I think an investment in a small impact driver will help you not damage your customer's property. Save the wedging for more robust machines like lawnmowers. I personally use a c-clamp on the side of mower decks, by the way.
The problem is the other side of the axle cannot be fixed. If it only had a slot for a flat screwdriver or whatever, it would be a different story.
Yahi tha jo main doondh raha tha👍
When you were taking that bolt out you could of used a cloth to not hurt your self when your holding the motor
Thinkyou
It takes a vacuum to clean a vacuum. Oh the irony.
it's a stupid design because the dirty air goes through the motor and if it starts to smell you can't clean it inside, the cooling airflow should be separate
Every modern vacuum cleaner has this style motor. Filters or bag is before the motor so these only get dirty if abused like this unit.
6:09 . you want a bit scrubbing action??. . use my ex girlfriend for that. . . she was a rayte scrubber. . and shes available too
Why is a freak did they have to use AC DC motors kin to use big ones that doesn't have to use stupid electromagnets
Kimi pls go back to racing F1 cars.
All right then 😁
This poorly ineficiet vacuum motors is na piece of hit consumes much energy for wasting the old vacuums consumes 1000 or 1100w maximum and conservates good suction
Yes I know. This is also VERY noisy motor.
I’ll bet you’re Finnish.
Oh yes I am.
@@vacuumtests9225 Your accent sounds like ISMO's.
@@michaeljuliano8839 Ismo Leikola oh yes funny guy :)
it looks like a brakepad
Brake rotors are designed with slots to blow air on the breaks when they spin just like this
@@johnathanrice3569 yes
How to clean a vacuum cleaner. With another vacuum cleaner.. genius! Shit. Now i gotta go buy another vacuum cleaner which is what i was trying not to do by cleaning the one vacuum.. is where they get ya.
You can buy spray bottle of compressed air and blow it clean.
😁😁😁😁
are you Finnish :D
Mehmet Filiz Yep :)
Perkele! Suomi ihmiset ovat hämmästyttäviä
Mehmet Filiz Yep :D
hello my friend
may i have your Email? it is important.thaks
Dude are you a butcher ?
Maybe :D
USE NUT LOCKING GLUE!!!!!!
Pawel no because then u couldn't clean the motor when it gets dirty
H