Thank you for putting in effort to show us what it looks like. What version of autel is this? Can it program the main computer N3/10 component the ME-SFI control module. Also can you program the front SAM? I got rear SAM that wanter got to the board, and also front SAM that shorted and burned the board so what I want to try is to buy them and try to program both rear and front SAM eith autel.
How this work if you still have error code recorded in the system Ask you because reading to many different thinks And can you cloning different serial number SAM or need to be exactly the same one Thanks
The SAM doesn't need to be the exact same number, as different SAMs have been superceded over the years, your just need to get one that is compatible with your vehicle. But in doubt, try to get the same, that way you will be sure that it will work...
I replaced the rear SAM with a used one and everything worked, but I get a warning about the rear seats not fitting, but in my car they don't fold down. How can I delete this and what program is it? Regards.
Hi Luis, I've programed my rear SAM same as you did, but i was in need to reset the "Fuel pump sensors" which i couldn't find to program or code, my fuel gages is still stuck on full and the reading shows an error: (90DA) + (90DS) any advice? Please note: i've checked the SAM module and all of its resistors and it seems ok!
@@LMAutoRepairs No sir, I've replaced the main battery and after the installation all of the features in the rear side of my car a "W164" didn't work, so i've checked the rear SAM and i found a little bit of water leakage from sunroof to that area, then i had to open it and clean it and re-program it, everything is working fine right now but the fuel gauge, it stuck on full all the time!
I have a 2007 w204, with prefacelift led rear lights and I want to retrofit the facelift led rear light. I saw on some groups and forums that the rear SAM needs to be recoded and they said I could do it with a regulat obd cable and a laptop? How is that possible, what software do I need to do that? Thanks in advance!
Not sure... could be that there is some software out there capable or coding the unit... Unfortunately I am not sure... Go on those same groups and forums and ask... 👍👍👍
hi i have a mercedes ml 280 cdi 06 version both front seats are not working but when u plug diagnostic tool in they work so its not the seats them selves is their somethin i am missing or would u know what the cause would be by any chance.
I would establish what is at fault, and would replace those only... The spark plugs, if they are "due" to be replaced, just do them all, the rest check first... 👍👍👍
I was just thinking, STAR/XENTRY is as straightforward like the AUTEL.or vice versa. So why I always grab STAR? Old habit I guess. Not that I have to program so many modules. Nice quick video Luis.
![Mercedes Benz C Class SAM Unit Diagnose and repair [Part 1]](http://i.ytimg.com/vi/tap4Ae_uF1I/mqdefault.jpg)
![Mercedes Benz C Class SAM Unit Diagnose and repair [Part 1]](/img/tr.png)
Thanks Luis, great video helped me fix my issues with a rear SAM on a 2008 ml350
☺️
👍👍👍
Much appreciated Luis, nice example of what maxisys is capable of when in the right hands!
☺️
👍👍👍
What model of autel do you have ??
@pedrosotolopez4457
MS908P
Good morning Luis! Excellent step guide as always
😊
Thanks!
👍👍👍
Excellent walk thru on this. Appreciate you sharing!
☺️
Thanks!
👍👍👍
Thank you for putting in effort to show us what it looks like. What version of autel is this? Can it program the main computer N3/10 component the ME-SFI control module. Also can you program the front SAM? I got rear SAM that wanter got to the board, and also front SAM that shorted and burned the board so what I want to try is to buy them and try to program both rear and front SAM eith autel.
Hi
This is the MS908P... and yes, should be able to program those as well...
👍👍👍
Thank you so much , I appreciate your time and efforts excellent job
😊
Thanks!
👍👍👍
Sometimes I think you learn more programming the modules manually, nice little short one this time Luis 😊😊😊
Agree...
👍👍👍
I assume this scanner should be able to reprogram the ISM?
If so can it change the ISM gearing to go into neutral etc?
Cheers!
Possibly...
Never did that particular one...
👍👍👍
Hi where abouts are you based? I’ve got an issue with my car that I’ve seen on your channel that you’ve diagnosed and fixed before!
How this work if you still have error code recorded in the system
Ask you because reading to many different thinks
And can you cloning different serial number SAM or need to be exactly the same one
Thanks
The SAM doesn't need to be the exact same number, as different SAMs have been superceded over the years, your just need to get one that is compatible with your vehicle.
But in doubt, try to get the same, that way you will be sure that it will work...
I replaced the rear SAM with a used one and everything worked, but I get a warning about the rear seats not fitting, but in my car they don't fold down. How can I delete this and what program is it?
Regards.
Needs programming/coding...
Similar to what I have done on the video...
Great video thank you for sharing
😊
👍👍👍
Hi Luis, I've programed my rear SAM same as you did, but i was in need to reset the "Fuel pump sensors" which i couldn't find to program or code, my fuel gages is still stuck on full and the reading shows an error: (90DA) + (90DS) any advice? Please note: i've checked the SAM module and all of its resistors and it seems ok!
Hi
First, why did you programmed the module?
Was that a replacement?
👍👍👍
@@LMAutoRepairs No sir, I've replaced the main battery and after the installation all of the features in the rear side of my car a "W164" didn't work, so i've checked the rear SAM and i found a little bit of water leakage from sunroof to that area, then i had to open it and clean it and re-program it, everything is working fine right now but the fuel gauge, it stuck on full all the time!
Could still be an issue with the rear sam...
Inspect the board and the internal circuit if the lever sensors...
I have a 2007 w204, with prefacelift led rear lights and I want to retrofit the facelift led rear light. I saw on some groups and forums that the rear SAM needs to be recoded and they said I could do it with a regulat obd cable and a laptop? How is that possible, what software do I need to do that? Thanks in advance!
Not sure... could be that there is some software out there capable or coding the unit...
Unfortunately I am not sure...
Go on those same groups and forums and ask...
👍👍👍
Great video, Thanks for sharing Bro👍
Love the results😍
Stay Safe Bro👍
☺️
Thanks!
👍👍👍
Rear vent windows are on GL320 which is x164 model. I believe ML320 is W164
👍
hi i have a mercedes ml 280 cdi 06 version both front seats are not working but when u plug diagnostic tool in they work so its not the seats them selves is their somethin i am missing or would u know what the cause would be by any chance.
Hi Luis. Unrelated question. I believe I have a spark plug issue for my car (P0300 code). Should I also replace ignition coil and or wires too ?
I would establish what is at fault, and would replace those only...
The spark plugs, if they are "due" to be replaced, just do them all, the rest check first...
👍👍👍
@@LMAutoRepairs Thank you so much
What scanner can be used to program my rear sam module for Mercedes?
Xentry...
@@LMAutoRepairs Which Xentry scanner do you recommend? I’m trying to program my rear sam as well.
Could send a link to the scanner you’re referring to
Just google Xentry...
That is the software...then you need a laptop and the VCI...
Or, you can get everything as a ready setup...
👍
good morning Luis
👋
☺️👍
I have order from ebay a rear sam for my w204 200cdi 2011.when i change it does it needs coding?
Most likely...
Specially if your car has functions that the donner didn't, or vice versa...
👍👍👍
@@LMAutoRepairs Thank you for your answer
Does this works on new modules also ?!!
Yes... that was how I have programmed the new module for this car...
👍👍👍
Can you code rear sam on the im608
I believe coding yes... programming no...
👍👍👍
Thanks for the message
You start your day early
Love the videos
☺️
I do...
👍👍👍
I was just thinking, STAR/XENTRY is as straightforward like the AUTEL.or vice versa. So why I always grab STAR? Old habit I guess. Not that I have to program so many modules. Nice quick video Luis.
☺️
👍👍👍
That's because Autel basically clones the factory software when it comes to these functions.
Which device model?
The Autel?
MS908P
@@LMAutoRepairs Yes, thank you!
Awesome
Thanks!
👍👍👍
Nice
😊
Thanks!
👍👍👍
😊👍
☺️
Thanks!
👍👍👍
Like
😊
Thanks!
👍👍👍
Mercedes s500 w220 jahr 1999