วีดีโอ

For summertime yeah

The hot pocket is great for maybe 4 mags then you are going to want some type of pic rail cover for the top rail and or gloves. I have never used a rail wrap that replaces the need for gloves unfortunately but in short yeah, the hot pocket has been great and I would buy it again. 😌

@@nickslosubi690 thanks dude, I’m in Cali so I train with 10 round mags that’s about 12 mag changes before I’d have to go and put gloves on I think I should be good then I usually don’t go over 150 rounds per indoor training session, only time I get to 500 and up is at an outdoor so this might work just fine then

Battle arms development Agency elite 10.5”

I bought one on amazon by a company called “nice cnc”. I selected my make, model and year. Its still working perfectly

Thanks for the quick reply. Great video

I bought one from amazon. Company called “Nice cnc”. It’s holding up perfect. Just select your make model and year.

Well I would but the gun has been completely disassembled to avoid breaking the new rule/ law for the pistol braces. Higher mount= less neck strain though. Try it before sht posting next time yeah?

All I had to do was loosen the clamps and spin it. Removing the exhaust is fairly simple if you have to but I did not have any issue spinning it.

I'm not allowed to say yes but If I were to do it, I would be super careful and try not to hit any fuel lines or anything that is flammable or can melt. The point of the torch is to just soften up the Loctite a little bit. There are chemical sprays you can buy that do the same thing without the heat risk.

@@nickslosubi690 I took it off and put small flame on the area. It came right out. Thanks for replying.

I would only run the one base plate in the gun while carrying it. Mag changes with this base plate tend to chew up your hand because it gets pinched in the half moon. I only use mine for the first mag that rides in the gun, spares are all OEM or extensions that are compatible with other models.

It is advertised to work folded or unfolded without a buffer ststem (tube, spring, buffer).

Thats what I thought at first but it looks like the M just has stronger recoil springs to counter the excess gas pressure. That would mean the M should have less issues with dropping the bolt on the first round and getting it into battery. Even if the recoil springs are the same and the M just has a crimped gas key, they would both suffer from the same issues.

All day, if you want a folding platform, get one that comes from the factory folding and you will have no issues. This is a solution that finds problems…

Shot a lot more a different day, this was all Freedom munitions .223 reman 55gr fmj. It did not run well unsuppressed. The gun ran unsuppressed with 5.56 but I keep having an issue of failure to feed on full mags. 25rds and below on a 30rd Pmag gen 3 and it runs great. Full 30 and it will FTF on bolt drop and on cycle. Cleaned and lubed it, the issue persisted. At about 200rds now. More to follow.

@@nickslosubi690 finally made it to the range yesterday. I’m having the same issues with releasing the bolt after changing the mag. It won’t feed the first round. Shooting suppressed 300blk with the ARIC-M. Think imma purchase some 300blk specific mags and see if that helps

@@wilsoncombatant6033 Try lubricating the guide rod rails. Mine got a little bit better when the springs and guide rods were wet wet wet. I still think it should operate wet or dry but thats just me. 🤷‍♂️ Good luck!

Initial thoughts are that its a great concept, but long term testing and evaluation would deliver a better answer. In terms of “is the idea worth it?”, that all depends on what you want and need. I rarely see a use for the folding function so in all honesty, the money could be better spent on training and maybe a good optic/ light if you don’t have one already.

right on

As of right now I can not recommend this setup. Ive had too many issues with not feeding the first round on a full magazine. 30 through 25 tends to be the sticking point where the springs are not strong enough in the ARIC to strip the rounds out. I used a few fresh mags straight out of the wrapper and it failed multiple times with intermittent success. The system would likely work with oversized gas accommodations and stronger springs.

Hey Will, This is just a quick video showing the new product functioning. Usually an AR pattern firearm requires a reciprocating buffer and spring contained in the buffer tube (back tube on the gun). This product allows the user to fire the weapon while folded when used in conjunction with their folding tube system.

@@nickslosubi690 very familiar how AR platforms work, got a few myself. My only question is. Where the bolt go though? Haha

@@willking8084 Gotcha, The bolt looks to be a standard AR bolt, the carrier is a bit different than standard, the buffer is gone and the action spring is now two smaller springs. The entire system is contained in the upper receiver similar to what can be found in the Sig MCX lineup.

@@willking8084 It pretty much gives you a bolt that is like a long stroke piston. So you can shoot it folded, but it only works with the Law folder.

Only the worst of ideas lol.

Mine did too 😂what did you do . I’m gonna try to tap it and get a new screw

@@LuiDineroo it probably fine just make sure you’re screwing it in as straight sis possible try to put it in the mag well without the grip first

Correct

The olight broke lol. Only stream light,, surefire and modlite now.

Thank you for the information. I just bought my SP9A1 Gen 2, 3 days ago. Need to get the brace for it, and some more magazines. Been shopping around and looking into all the aftermarket parts that are available for this gun. I bought it because I got it for $700 at my work/local gun shop. Couldn't resist. Especially because I kind of like it since I first held it. Then I did reviews and I'm glad I got the Gen 2 instead of the A3, roller delayed. If I had the funds to buy an SP5 or a CZ Scorpion, I totally would, but for my budget (stupids bills, I have adulting) this was perfect for me. Still looking into things before I buy away and end up with useless parts I don't use... Anything you recommend for aftermarket parts that you like on your Gen 2? Please and thank you for the information.

I'm not sure what spring I have in mine, Would have to check the serial number for when it was made. got it around march 2021 So it might be "New" enough, IDK. Thanks for the heads up!

I hope a different material makes the difference but there is no doubt that the first gen mags were brittle. Too many people having issues to ignore. The next few months will tell us how good these new mags are.

There’s probably a way, but I have not messed with it. Be safe about it if you try, thats a serious system to mess with.

these things are built like a sherman tank, where the stick mags were like a geo metro.

To be honest, the curved mags feel very similar to the first gen stick mags with no metal lips. Im sure we will know in a few weeks how good or bad these new ones are.

never needed steel in the first place mine are old af n still look brand new but i did just order 2 curve and 1 20 shorty ..

You see the dislike button? Use it, LOL

Also, Did the video help you fix the issue?

No sir, This Magwell stays on 100%. I recommend some blue thread lock on the set screw but even without the thread lock its GTG.