วีดีโอ

Damn...I know how to clean. I don't know how to remove.

Thank you for showing me this. Last time I did this I blew a 3 amp fuse somehow

A pleasure to watch a professional at work! Learned a LOT, thanks!!!

you dumb... heat cannot be reduced using water just use cut to 2 parts and you will see bad connection.... stupid video

Set up before you wet up

Great work my dude 😎💯😎

Bring back constructive comments! Just get a 5 horsepower or betweer wet vacuum and suck out the discharge end every so often. Doing this will greatly reduce the chance of a clog at the drain pan nipple and won't overlook the portion of the pipe going back to the air handler. 😊

Literally just did all this and thought let me check TH-cam see if anything else should do. You video spot on to what I just did. Heading to my rental to do 4 more boilers tomorrow

How do you remove them?

That drain line doesn’t have enough fall for my liking. The “warter” won’t flow out very well.

This guy dont know shit😂 leaks

YOU MUST to learn how to solder ....!!!!!

Nice job. What type of gas are you using?

Nice job. What type of gas are you using?

The instructions for the primer and glue I sold at Home Hardware are different than the instructions you show in your video. They say to prime the fitting, prime the pipe and then prime the fitting again. Then you put glue on the pipe then the fitting and a second time on the pipe. I see that you prime both the fitting and the pipe only once. Then you put glue only on the pipe and use just one coat. Is this how you do it for all PVC applications or just for this because there no pressure to cause it to leak.

The Drain line should have an air vent after the trap....

Do you recommend keeping a cap on the upward pipe or is it ok to have it off? I'm asking because our house was built 2 years ago and the builders never put one on.

Being open and very accessible I would do sharkbite...but what do I know

My drain pain is rusted out. Is there a way I can fix it epoxy?

I have that same system. My coil is leaking freon. I have to recharge it every 2- 3 months. Can I replace my coil? Where do I buy it?

Great video !!!

BA- BOOM! good video

ok so your old drain is not up to code and pitched about 15* downhill, your new drain is not up to code and pitched about 15* downhill but has a Union ... which does not satisfy the new standard for a non destructive method of cleanout. just gives you an opportunity to make a bigger mess. a second union between unit and trap would work ... you haven't satisfied the IEC mandate for Condensate pipe insulation. or the IRC standards for overflow protection. and for modern equipment a P-Trap isn't deep enough, a j-Trap is required.

Very good video. My A/C drain line comes out from the pan, makes a couple 90% turns and connects up to the PVC drain that goes to the floor drain. I don't see any P trap. Should I install a P trap? Does your PVC cutter cut the pipe straight? I had purchased one that cut the pipe but the cut wasn't perpendicular, it was on a slant. I returned the cutter. Do you have a recommendation for a PVC cutter?

Never knew you could clean those. 🤙

Nice work! 👍

I added a HS kit. I also went from a single pole to a double pole contactor. Should I hook the HS relay BEFORE or AFTER the my new switched pole?

what type of wire you used to connect the capacitor to the contactor? Mine is cooked so bad and I can't see any markings on the side.

That was so awkward to watch

Can I use a spade contact for a car?

Nice video, thank you!!

Hi Bill . I have question for you . I have cast iron boiler made by slant fin , it is direct vent Victory model . Boiler is over 20 years old by now. I removed old circular pump on return side of boiler do to pump rusted and leaking water . Treaded part of boiler on return side have internal threads it 1-1/2 diameter and they are not in prefect condition do to age of boiler , I can still able to thread new pipe in boiler . My question is how do you sill this old threads to make leak free connection? Thank you

So, if it is in the summer, and the compressor heater isn't required. You can at minimum substitute a two pole with a single pole without any concern? Fan dosen't have to be hot?

Amazing step by step tutorial. Thanks a lot!

Hello - i have a few questions... this looks similar to what we have in our attic. What if the clean out isn't capped off, does that cause problems? If you know there is a clog and want to use the air compressor to push the clog out of the drain, can you use the clean out spot or is it better to create one of those sections where you can easily take the PVC apart?

So I have a question. What is the trick with the pressure washer. My boss told me I need one to clean the coils, so I bought one. No idea what I am supposed to do. Do I just aim straight and hope for the best or is there a trick.

You did'n't relieve the pressure first by opening a hot water faucet

Just had a unit installed 5/6. AC stopped working this morning 5/12. Called the installer which doesn't have the greatest reviews, they came out and found a burnt/melted wire on that side of the contactor. Said it had to be a surge and charged me $321 for the repair. I know that is. You know that's bs. I have no problem stopping the check.... however, what do I need to do to assure this doesn't happen again? It's a brand new unit. Do I need to pay another company to come check everything or can I just check certain connections?

Very good, basic electrical knowledge

Thank you

❤

guy is spot on here great work

Whoever brazed those lines didn’t use a fire blanket or brazing putty lol

do you remember the psi you used ? thanks

No eye protection, heating the copper pipe with a direct flame as opposed to heating the body of the valve. C- at best.

Using a wet rag is not a a good idea.

Etwas Planlos der gute Man 😂Paste rauf ,Paste runter dann entgraten 🤷‍♂️🤷‍♂️🤦‍♂️

Etwas Planlos der gute Man 😂Paste rauf ,Paste runter dann entgraten 🤷‍♂️🤷‍♂️🤦‍♂️

Good job 👏 🙏 Thanks for the tutorial

Never trust a tech who wears flip flops with socks…..