วีดีโอ

I need to replace the new head for my Sony 3 head 222esl cassette Deck where will I get to buy the head

Just finished my brand new VICKY-TWENTY build from Bob’s PCB. All brand new except the VIC and ROMs!

I watched your video and then threw my old tc-wr590 in the trash. Geeze, you have the patience of Job.

у меня qnap ts-264 такая же проблема. чем можете помоч?

Good job man!

Thanks but it didn't work on my ts251. Started with more weird behavior. Sometimes blue USB and red hdd2 leds are on, sometimes 4! hdd red leds are on althrough this is 2 bay nas. Voltage measured without resistor is 1,86V. I guess no luck for me :(

13:10 That pad is insulating the solder connections (THT) from the USB connecting wire. Not sure if they were forced to do this or did it on their own, but this is quite usual in consumer electronics. Logitech still cares. About your solder mixing and breaking again, that is not really true, atleast I have never heard of it, or seen it myself. I would be more concerned about the pass ripping of the PCB than anything, especially when soldering a second time

Hia, nice video. The Issue 1 board is a later German Issue 1, which actually came out after the "English" Issue 2 and probably same time as the Issue 6 boards, which is why it uses the same 'blob' style Malaysia ULAs.

Many THX from POLAND it works for me too - TS-451S

Brother, how to increase output treble in my Sony 3 head 222esl deck , my deck is not producing clean treble even i play with new tapes why, can you give me advice, if i change circuit doard will it produce more treble, im frm india

I enjoyed your video. I have an X-540 system that's no longer producing output from right rear channel or the sub. In your opinion is that kind of fault fixable in this system?

No meaning to be an ass here but TL DR would be very helpful here. I am just trying to get to the actual problem. And why Intel is at fault, without going to the lengty video. For people searching for it , as I understand it : TLDR: There is a fault in the CPU hardware that leads to the voltage being to high. This can be sorted with a workaround fix that the poster kindly made very clear. But this is a workaround and will fail eventually. So this workaround is only cleared out to get the data of it. I just installed a thirdparty software diskgenius to be able to read EXT4 on windows 11. This led me to be able to copy it all safely without needing nas. I didnt do raid so for me it was fairly simple.

Great video and work on this old machine Bob, and thanks for alerting me to a great new channel to follow 👍

Nice Bob, I'm really pleased you were able to detect some signs of life in the old girl! Thanks for the shout out and links 😀👍

Today my G413 met my desk and my hammer. Waiting for my Redragon K587 to arrive. Irony: I have a spare Logitech, but it's a membrane one XD

Out of curiosity I tried the same 3 line BASIC benchmark on an Electron emulator, and got exactly the same results. It was much slower in the higher graphics modes that use more RAM.

23:20 - those two keys are different, but on a EU market I guess they are also labeled differently. The right one is what we call a Graph ALT (ALT GR) and it is used to alternate between special letters, like e-ę, a-ą, s-ś, c-ć, z-ż, x-ź, n-ń etc. I was surprised to see, that your's (well, your customer's keyboard) doesn't have that ALT GR!

To reset your device to factory defaults, please follow the steps below: *Step 1:* Make sure your device is connected to a network and the status light is solid green. *Step 2:* Please use an unfolded paperclip to press and hold the RESET button for at least 20 seconds while your device is plugged in. *Step 3:* Please wait 60 seconds for the device to reboot. And this process will change all your settings back to the factory defaults.

This gives me vibes of when you used to be able to get the password of a DLink router through SNMP.

So i have 3 of them , i understand they are not easilly fixable , so i have to throw them away ? :(

I have 3 of them in my company , all of them same . Terrible , i really like this keyboard . Disaster

Nice job Bob! A cord with overspray is much more interesting than a normal plain cord! 😉🤣

Thank you this saved my data. Great info

You probably know by now, but... the game menu, just use the up and down keys to navigate it.

That ultrasonic cleaner is a bit nifty!

Doesnt work in my case, I have opened many times and the issue has come back. I have also changed many switches and nothing...

Dude, cheers for the video. You have a cool voice. Subbed.

I'm inclined to agree with your decision to return to a home-built NAS. I am planning to build an off-site backup NAS rather than buy a third QNAP. The main difficulty is coming up with an affordable low-power solution. Thanks for sharing your experience.

I've had to resolder the g413 that I've got about five times now, logitech's support and rma basically told me to pound sand after the second time so they're off my list of folks to buy from once the g413 finally dies for good

My TS-451+ just died. Internet search found this and some other videos about the 100 Ohm fix I soldered in a 100 Ohm resistor and my 10 year old 451+ came back to life. No data lost. But now I have to wonder how long before the thing finally dies. I really do NOT want another QNAP NAS with unreliable intel components - but the AMD stuff is 2X the cost.

is it not a chopped finger from MCM ?

Can you tell which CPU you have? I've read Intel fixed this with Stepping D1 on the J1900 but I haven't found any info on what that looks like with CPUINFO. This is what mines shows model name : Intel(R) Celeron(R) CPU J1900 @ 1.99GHz stepping : 9 microcode : 0x90a

Great video 👏

Thank you for the video, my TS-451 dies unexpectedly, its symptom was in a boot loop and the boot loop shorten to two loops and then stopped. You mention pin 1-100 ohm-pin 8 is to lower the LPC clock voltage. How about pull up the LPC clock voltage? I am not sure if my TS-451's LPC voltage is lower than 1 V, but I wanted to know how to pull up the LPC voltage? and see if that help.

We have two G413's and both eventually developed the dreaded double typing issue, first one lasted about a year and 2nd one only recently started so it lasted about 3 years, seems like once the issue starts it spreads like a virus throughout the keyboard, will not be purchasing Logitech mechanical keyboards again lol. on a positive note my old Logitech K310 non mechanical keyboard still working great after 11 years of use so far.

Good work Bob. Lovely old machines these G4 iMacs. I wanted one so bad BITD. Now I have several 😂

I've been using Windows 11 on my personal machine for the last 2-3 months but still have a MacBook for work. WSL does a pretty good job at being a unixy command line, but it has some limitations around USB devices, thankfully none too critical. KiCad seems to be more stable on Windows. I still get occasional crashes on MacOS even when everything is at the latest version, but on Windows it is rock solid. I've also set up a VPN to allow myself to get in remotely from the Mac and access the desktop via RDP to run software that I can't on MacOS, which is mostly FPGA dev tools. Wasn't sure how much I was going to like or dislike the change but so far I think I could honestly say I'm not looking back. Once I'm in a familiar app I forget about where I am.

Schönes und ausführliches Video. Wenn ich es richtig sehe, wird hier nur auf die Antriebsseite eingegangen? Ich habe das gleiche Gerät, welches motormäßig einwandfrei läuft. Ich habe jedoch ein anderes Problem. Ich weiß zwar, wie man den Calibration-Mechanismus bedient, jedoch schaffe ich es mit keiner Kassette, die geforderten Werte bezüglich BIAS und RECORD LEVEL zu erreichen. Meist ist der BIAS zu niedrig. AUßerdem beeinflussen sich BIAS und Record Level gegenseitig. Woran könnte das liegen? Nice and detailed video. If I see it correctly, does it only deal with the drive side? I have the same device, which runs perfectly in terms of the motor. However, I have a different problem. I know how to operate the calibration mechanism, but I cannot achieve the required BIAS and RECORD LEVEL values with any cassette. The BIAS is usually too low. In addition, BIAS and Record Level influence each other. What could be the reason for this?

what is the usb to serial adaptor you are using? I just ordered one of these (in transit still)

My TS-859Pro+ is still going strong after 14 years of continuous service. I guess they don't make 'em like they used to.

I was really hoping that this would be my problem, as I had multiple bouncing keys. Finally took it apart today, and it would appear the joints are good. Likely my problem is corrosion in the switches as other people have had issues with. Of course you have to desolder every switch just to remove the face plate and disassemble the switches themselves. Still a great video!

My 451+ suffered from this. Just replaced it with a 673A last week with a Truenas Scale box as a backup that syncs once a week. Lucky for me that QTS on the 673A sees all my data from the drives from the old qnap.

Hi Bob. Very helpful and informative video!. Am curious, what did you do as a long term solution?

These are some of the most reliable of the original c64 power supplies. Those power supplied are NOT known to go bad. You are thinking of the potted ones. You could just change the caps and replace the regulator. Myself as a experiment I wired a inline Aliexpress dc to dc converter for the 5v ouput. All of the insides are left as they are. I do plan to replace the inside of a Sinclair 48k power supply as they get too hot even without being potted but this c64 power supply didnt need what you did.

Is there any bug free CPU that this motherboard can accept?

Great video mate! The best NAS in my opinion is one where you can simply remove your drives and access the data via Linux/Windows... Obv if the data is encrypted at rest, that's a different issue... Cheers from Africa

Thank you, I was able to repair my keyboard. I have to say, this is a terrible design by Logitech and extremely poorly made.

Thank you, you also saved my Keyboard, the"E" Key on my board had the same issue.

seems to be a decent tutorial, but i HIGHLY advice anyone thinking about buying a g413 to stay clear of that thing, it is misdesigned garbage.

My 251 die yesterday.