วีดีโอ

I've been trying to replace the cabin air filter on my 2003 Ford Taurus, but it has a metal piece right above the air filter, instead of the flap that's on yours. I can't find any screws or bolts to take it off. Have you ran into this before?

You missed the fine point pen under the scratch point tip. There are three points on that pen, its amazing!

wait does the paint have to dry before adding the compound?

Very, very good video, fantastic.You should have way more views than what you do.Hopefully your channel source

lol I got the same car idk if same type but 2014 impala limited police pkg

Prodact link

How do you color match

Thats the cleanest Impala engine Ive ever seen!

How do you find floor joist

That car interior is Super clean,your video is very informal,has excellent lighting and explained very clear. Thank you.

I have an 08 3.5 I did mine in 10 minutes a lot easier then this I went under there's 2 10mm bolts took them off pulled cover back saw the sensor un plugged it and put it in and you can use a27 mm deep well no extension needed and fyi put a little engine oil on the rubber o ring on the new sensor it will prevent any leaks and do not over tighten new sensor problems solved

I opened the clearcoat part and nothing came out, but the brush is wet. Pen is 11 years old. Is the pen garbage now?

Hello, possible to list the molding description and the wood that used. Thanks

Toward the end of the video, the driver of that Chevy crew cab had the right idea to steer into a snow bank. He or she should have stayed in the deep snow until coming to a complete stop. The mistake was to steer out of the snow back onto the ice.

Why do so many people just HAVE to go somewhere when the roads are that icy?? I don't mind driving in deep snow, but I don't knowingly drive on ice. Call in late and wait a few hours until the anti-ice / anti-skid has a chance to work. If you are an "essential employee", you need to make arrangements to get to work before the roads get really bad. If you must drive in these conditions, you need tire chains; You won't see fire trucks and ambulances out in this weather without them. I've even seen tire chains on sand spreader trucks. And remember: Anti-lock brakes are of no help on ice. You need to go back to the old method of pumping the brakes to keep your wheels turning so you have at least a little control.

How I can get this product Dupli Color in India?

Thanks for the video.

61,404????????????

If I go to Napa, O’Reilly’s, Autozone, (wherever) and ask for an actuator, are they going to know what I’m talking about or look at me like I just talked in some kind of gibberish?

Where i can find

Do not try using brush to brush paint along surface, just dab it. Lightly wet sand paint after it dries using a flat block. Go very lightly as not to take too much off. Use 2000 grit. Clean off dust, then dab the clear coat on lightly. Do not brush stroke it. Wait 24 hours, then lightly wet sand with 2000, then 3000. Clean and polish with light compound. Apply wax after all the light sanding marks are gone.

I watched all the way through the video. The calibration method could be used at the start as part of trouble shooting. After I watched the video I ran the calibration. This is all I needed to fix mine.

Nicely done

One down. 50 more to go >.< Thank you and God bless. im definitely picking one of these up if I see one

Brialliant WJD well done fab instructional video , from west of London UK. Graham [ Chartered Engineer ] 👏👏👏🎬.

Excellent Brother!!! I'm doing this soon, and replacing the door threshold also... Thank You Much Chuck in Michigan

Yeah, I’m not a big female so I was able to hang upside down and change it😂. Also, I use a battery and a mini clamp to angle the shaft. That way I didn’t have to use the ignition. I found the idea on a TH-cam video here.

Is that paint durable?

Good one, thank you

Was looking this up before applying to my 03 impala, small world.

ive replaced the 2 easy ones in my 09 in the past couple years; one being this summer... and now ive got not a clicking noise but more of a water pump noise coming from behind that dash.. absolutely been loving this car for a good 8+ years.. and the clicking noise has been my ONLY issue! luckily they were easy cheap fixes from a friend of a friend for ~100$

I want to try this, but when my negative cable is disconnected, I can't remove my key from the ignition; it gets stuck in the accessory position. Any idea on how to get around this?

Name of the product, plis mister 🙏🏻

Thank you! My brother had this problem for YEARS and now we know.

I'm getting ready to do this. Thank you.

It is just the actuator going bad eventually? It sucks that you have to replace it.

Ху..ета американская

Are all 3 actuators the same style ?

good job , Thanks for the info

Thank you So much for doing this video. My door has the same rot and I was told the entire door and frame have to be replaced. Now that I see what you have done, I will repair my door frame the same way and save money.

So all the actuators are the same or right

I also did this, and it left a mess on my chassis

how the hell is that thing so clean under there, if i ever dare to attempt removing the manifold heatshield bolts on my it would take HOURS and an oxyacetylene torch you guys in the south of the US have it too good man, meanwhile i have to fuck around with a torch cause i'm in canada

That's a really nice Impala!

Help. What do you call the vertical wood piece (4:11, right side of finger) that is also rotted? Got that & under my windows (plastic siding, insulation foam, rotted wood). Don't know what that wood panel called to look up.

you did not show step by step>like you said> no videos out there for us:(

2024 and they still can't come up with something better than this. No wonder aliens do not come here. Humans are dumb.

*I watched this video and ended up ordering 3 of them. Easy install, no more AK47 gun sounds* 😅

Can you get this at local auto part stores or online ?

Out of curiosity how long did it take you to do this job?