วีดีโอ

Thank you very much for the video I was wondering do you have any videos on custom framework or jailbreak PS Vita thank you

Can you connect multiple controllers just like on pc?

Subscribed! after like 4 tutorials this was by far the best. Guys dont forget to format your cards from the PSP menu and dont forget to change your 661 update file name from 661.PBP to EBOOT.PBP. Cheers!

your explanation is very understandable!!

I have the same smallrig batteries, but while the indicator pro is 1% in the camera, it shoots video for 20 minutes without interruption, do you have the same problem?

IMPORTANT INFO FOR NEW PEOPLE: YOU MUST FORMAT THE SD CARD ON THE SYSTEM BEFORE TRYING TO ADD THE UPDATE FILE TO THE CARD. AFTER THAT YOU OPEN THE FILE PSP, THEN GAME ON THE CARD AND ADD THE FOLDER “UPDATE” in all caps AND DROP THE UPDATE FILE (not the folder you must open the folder and copy the file inside and paste it into the update folder) AFTER THAT IT SHOULD SHOW UP IN THE SD CARD IN THE GAME SECTION IN THE PSP

Good attempt man , bit of friendly advice , the cpu/southbridge require ALOT of heat , ive had to heat them badboys up for close to 10 minutes at 450c before it even started to reflow , and the xbox board might as well be a giant heat absorber which doesn't help , i found by keeping it elevated and off the silicone mat was a little faster but they do take a while and you have to do them one at a time while keeping a eye on the caps near them dont go pop there a pain the a s s , might be worth trying to reflow again and making sure it does move with the slight nudge test , thanks for the sub my dude- Chunky

Thank you very much I tried to follow your guide step by step my system software information now says 6.61 pro- C. Did I do it correctly as I notice on your system information it doesn't have the dash and the C? thank you for your help

The thing about the old atari joystick is that they're really simple. A battery and a light and some wire can be used to test it.

You should have found out the secondary code first

The sounds of the front cover getting pried open sounded way worse than what it was. Great tip with the spatula. I've always been a "squash"-guy, but will try out the spatula. I think TronixFix would be proud of that paste amount! It would have been nice if you'd taken the time to actually show a clip at the end where you start the console with the speaker connected. Other than that it was a nice, clean fix :)

Valiant attempt. May warrant a revisit in the future. I've never opened up a 360 before, is that circle warranty sticker always there? Not sure if I think it looks legit or from some third party 😂. That thermal.... well, I can't call it paste, more like thermal dust, looked like something from ancient Egypt. When you applied heat with the hot air station, what was the reasoning behind using a thin nozzle? I never pay attention to what nozzle I use, just using the one that happens to be on there 😂 Also, lovely accent!

hey man thanks for the sub

This device is trash. You cant even tell if its charging or not. Returned immediately

Why is it the battery percent didn't show when you charge your gadget.. im just asking?

Hey bro after the update of 6.61 what are the additional options or features you get in the update ??? And if you have Instagram do let me know I have some query’s

Mine is a Street 1000 series will it be possible

My psp still says (DADADADA)...

Hey mate first yoou want to get the secondary error code by holding the sync button and pressing the eject button 4 times and different parts of the light will light up eg 4 lights light up. You get a four digit code where each light is respective to their number except 4 which means 0. then go to xenonlibrary and find the secondary error code there.

This shit dont work.

Got psp 2000 and still have the error 80010005 or 80020321 if anyone knows what to do

Plz reply to my comment ( question) on your 1 year old 2nd psp firmware and infinity installation video

Plz reply to my comment ( question) on your 1 year old 2nd psp firmware and infinity installation video

Plz reply to my comment ( question) on your 1 year old 2nd psp firmware and infinity installation video

I think you have not provided the " 6.61 pro c2. Pbp " Folder in the link.

@Pixel_Fix plz reply to my previous comment

I replace the GAME folder with the OG game folder, now its showing all files corrupted, what to do, i am updated to 6.61

thx for subbing

This is probably the easiest procedure that I have ever seen on TH-cam. Great job! Thank you for posting this. I might just try it myself.

Thank you so much for the update file link mate, I couldnt find one anywhere online all the links I found were to dead websites

heating up is temporary fix at best. it needs proper repair - measurements of voltages and resistances, proper chip reball. no picture could be hdmi connector. surface level blowing with heat gun is not the way.. board needs to be on a heat plate at some 150 c at least and heat gun is last bit to get solder liquid under chips, but only after proper reball. send it to north west repairs, dude is gpu wizard

The first thing you do is get the error code. Then you butcher it.

You rework station probably can't get that board to a high enough temperature to fully reflow the chips. I had the same one (my son uses it now) when I first started out about 14yrs ago. A board pre-heater would help a little, but a new station like the Atten ST-862D will also serve you well in the longer term. I roughly tested the Atten and the 858 with a FLIR cam to see how much heat they could put into a board and there's a decent sized difference. Both were in a clamp stand so they were the same distance away from the scrap board I tested it with. Thanks for the video, I've subbed so I can watch any others you upload.

That's a shame. It might be the main IC under the fan got damaged due to overheating when all the thermal paste dried out. Or it could be as simple as replacing the electrolytic capacitors.

This is byfar the best way to damage it beyond repair.

You did so well but I think you will get it going, I’m not sure about what else could be causing it apart from maybe a circuit, tho I’d take a closer look at the board incase there’s any part that needs a solder. Could be weak around cpu or if anything might be a power supply issue even tho it powers on, as you have already sorted out the main heating issue. 😁

That's not how you do it. You never reflow a RROD in 2024, because it was never bad joints under anything. Use the hold sync and press eject function to get the code and look it up in XenonLibrary

CORRECTION NOTE : In the video i claim it cannot be used with a camera cage on further testing that statement is incorrect. It can indeed be used with a cage tried and tested with a sony ev-10 and smallrig cage, sorry for any confusion caused and thanks to @philippc4586 for asking me to double check.

Is it impossible to use it with a camera cage???

I could do with one of these actually.

I like your reviews 0:38 Knob Screw Mate lol

Excellent review, keep it up your doing Great😁🤘🏻

Thank you! Worked on my PSP. Also had no idea before this that I needed to reformat my card to really make external stuff work!

This just made my psp geek out and now it’s stuck with red screen with error messages in Dutch. Can anyone help?

Thank you very much.

Anytime I try to use this steps to update, it appears that' the update cannot be started. You must use the update data that is compatible with the model in use'please help me 🙏

This really helped me. All the other tutorials I saw skipped a step where you had to create the update folder so I wasn't sure what to do. Also a ps3 controller charging cable works on a psp to connect it to a computer if you have one. I used my ps3 controller charging cable to update the psp through the PC I have.

I was going to ask if you plugged the speaker back in. LOL.

Whats your opinion on upgrading the ram

Has anyone had problems with dongles not working with their misters I cannot get any to work in mine