วีดีโอ

It is a good machine! power setting though, 100% on the dial or ealse you will get varying results with different temp in your work space as the dial uses a potentiometer. If you are using Lightburn, turn the dial all the way up and set your power in lightburn to less than 100%. You will find it easier to manage especially if there is a potential for someone to knock or alter the dial.

Thanks so much ❤

I love you🥰😍

Than you for all your tutorial videos, I am new in laser engraving and the videos are very helpful to me.

I ll take the waste. Fûçk Bambu labs and their customer service or lack there of. What do they care they have my miney Failed to calibrate out of the box, cannot link to my phone either. Worst decision ever at least my Ender 3 only cost 99.00. F Bambu.

thank you so easy to understand

fab video, if I wanted to do that with outline hearts is there something else I must do, as I press unite and it looses the outline, I hope that makes sense x

Just what I needed. Thank you for sharing this

great tutorial. now do have any print and cut ones?

I haven't been able to get my unit to go past 3 in manual mode without over heating.

If your using light burn your ptokect is not ruined if you interrupt the engraving you go to preview and woth slider get back to where it stopped engraving and the click on start laser from here it will start engraving from that point and continue

is k10 suppose to be an upgrade version of the k8 wainlux? or is the k8 the upgraded version of the k10?

I have the text on the path. Why can't I move it around once the text is on the path?

I bought my laser only 1 week ago, but tonight I learned more I learned in 1 week about Lightburn. Thank you so much.

Thanks a lot using it now :)

why doesnt my Lightburn have the tab feature, continuous frame?

Also, when I copied the waved text, and pasted, now the text is straight again.

I created my curve on a text. Now when I have my selector arrow picked, I am unable to move the text to place it on the banner I need it on. What am I doing wrong?

Thank you so much for this easy tutorial!

Thanks

thank you so much!!!!!

thanks

Your a legend, saved me heaps. Awesome video

One thing I've always wondered is what are the fumes / off gassing like for a filament printer like the Bambu Lab A1? I have 2 small kids and no garage/good ventilation spots- so i'd want to set the 3d printer up on a higher shelf in my office. So i want to make sure the office won't be overly smelly while I work, but also no toxic fumes in the house for the kids. I've heard resin could get pretty smelly , so i was wondering about the fumes for one of these

Adding 'pages' to the software would fix it all. Thanks for the workarounds.

Wonderful review, subscribed ❤

I always appreciate your videos!

Why have you used two containers for your water.

I’m trying to engrave some text, but the simulation shows the laser filling in the letter if I have a letter like an “A”, or “R” Do you know how to stop this? If so , please let me know, it is driving me nuts. 😢

When i try this, it inverts and flips my text. What am i doing wrong?

Your tutorials are awsome. Thank you.

Thank you, just what i was looking for, great tutorial.

nice video very straight forward,, have you ever tried your machine to engrave or cut atleast a 5mm sintra board? greetings from philippines..

Love it...I subscribed!

Thanks for explaining the system and terms in a way us beginners would understand lol. Sounds like that might machine might be for me!

Thank you so much!!!

Thank you. If I copy my design 3 times so I can change the kerf offset to run a test, it changes all the designs when I change one of them. I'm stuck

can you please make a video demonstration of how to cut a rectangle 300x200mm long from 3mm plywood....it is possible?

My text is coming out as a mirrored image when I try to do this. Why is that ?

hello Hi, I have a problem with the engraving setting as the cutter cuts the lettering in a mirror image. Can you suggest how to change this?

Very help

OMG, on my knees bowing. Thank you so much. Earned my sub.

very good, short and precise!

Great video great explanation thank you so much

This is the best video on how to use the Xtool F1. This helps a lot. Thank you!

Thanks for great explanation you are good teacher.

Hi, very instructive video. How precisely should the sheet be placed on the mat? I have a Cricut and if the sheet isn't perfectly aligned on the mat, the cut will be off-center.

Thanks so much for your video it was very helpful. The only thing I'm wondering about (I'm researching for my 1st 3D printer) if the printer has an odour of burnt or melting plastic?

Can you pipe the air intake and exhaust to out side

So well described and easy to understand. Thank you.