- 10
- 189 391
tannerjthomas
เข้าร่วมเมื่อ 27 เม.ย. 2010
Garage KX Motorcycle Repair
วีดีโอ
DIY KX450 Top end disassembly
มุมมอง 33K3 ปีที่แล้ว
This how to disassemble the top end on a 2016-2018 KX450
HOMEMADE FORK SEAL DRIVER. Save $50
มุมมอง 24K3 ปีที่แล้ว
How to make a cheap effective fork seal driver
HOW TO: EASY TRICK for oil seal install for KX450
มุมมอง 25K3 ปีที่แล้ว
HOW TO: EASY TRICK for oil seal install for KX450
HOW TO: CORRECTLY remount and properly align your dirt bike front wheel
มุมมอง 29K3 ปีที่แล้ว
How to properly remount and align your front wheel
DIY KX450 bottom end disassembly and case split
มุมมอง 14K3 ปีที่แล้ว
KX450 Bottom end disassembly and case split 2016-2018 models
JB Weld dirt bike case fix KX450
มุมมอง 4.8K3 ปีที่แล้ว
How to fix case damage on a KX450 with JB Weld
Very clear and to the point. Thx
❤❤❤😢❤😢❤🎉
❤❤❤❤❤❤😢🎉❤😊
Or can I use just the sprocket to seat the seal ? I did this method (using the washer/ spacer) but I tightened till sprocket was flush, could that be you far in?
@@deatrichpatterson1999 yeah as long as the seal is flush with the face of the case you can use anything.
@@tannerjthomas ok, ima just use the sprocket this time and see if that’ll work, seems like the washer comes out a little on the back which can make the seal go in further when using the washer and the sprocket together if you push the sprocket to the case….. if you can understand that 😂😂 lol
Did you go all the way to where the sprocket touched the case ?
What size nut is that, what size socket do I need for that nut?
Will this work for a KLX450R?
Do you smash the washer to hold the nut in place?
I am too dumb to do this, I can not for the life of me wrap electrical tape around my fork evenly enough to get this to work
🔥🔥🔥
Brilliant thank you
I’m having a hard time with my 2007 kx450 it just locked up I need help please
I have a 09 kx 450 would that video work on this bike.
Some things will be different but overall similar. Be sure to check the torque specs on your specific bike since they may have some different for your 09
Well I’ll be , I was about to belt and Braces a device for the above 👍🏻
G E N I U S!
Was there a u clip in your kit? And if so, where in the counter shaft did you put it with the seal installation?
nice
You forgot the spark plug o-ring under the cam cap
Must have gotten edited out.
Hello @tannerjthomas, thank you so mich for your video, it helps a LOT arownd here, have a good one! ✌️
Thanks for the video
Did those forks are stiff!
They are. I run mine pretty damn stiff. Lots of big sand whoops where I’m at so it helps with those.
Your video was a lifesaver. Thanks for posting.
Glad it helped
Looks like if you aren't replacing the crank, you don't even have to remove it from the left case/bearing and it will slide right out and back into the right crank bearing.
Yep that’s right
Que tipos de rodamientos lleva el cigüeñal ? Sirven unos c4 ?
I have a Kx450f and when I turn it on it produces gray smoke, what is the problem?
That could be a bad head gasket allowing coolant into the piston
Thankt bro
Top shelf video! Great work!
What year bike is this engine?
2017
I know this is old, but what year is this one? Im doing a 2014 kx450f and want to know how similar it will be.
It’s a 2017. They are very similar.
@@tannerjthomas Thanks for replying so fast! this video is going to be one of my main helpers alongside the manual. Hopefully I can get it done without any trouble.
I rebuilt my motor and had the same oil leak issue thought my seal must’ve gotten messed up from when i first installed so I replaced it same result. Good thing i came across this video because i thought that I forgot something internally and was dreading splitting my casings. Thank you🤙🏽🤙🏽
Glad it helped
Does anything hold the oil pump gear on? Or does it just sit in place
👍👍👍
I have the same bike I got it with a blown head gasket and I replaced it and it blows coolant out the right side of the top end .. but also I do not have the original to top cylinder both on the right-hand side I have other both I had made to work but I don't understand why the gasket leak still maybe head is warped or could it possibly I installed it wrong? Any advice would be appreciated
This puts a lot of force on the inner lip which is not ideal. It's made worse because you have to drive both bushing and seal at the same time. I've had good luck using PVC of the right size, an old seal cut in half or even carefully with a flathead
Thanks! This worked perfectly!
My sprocket is bottoming on the case? There is no spacer in any of the parts fiche's and I see you dont have a spacer either. Any thoughts?
It sounds like your collar that goes on the shaft before the sprocket isn’t there. Did you make sure to put the collar back on?
@@tannerjthomas it is there. It may be deeper than it should be however since I saw a note on that on this thread.
Does your seal have a spring ring around it. Shall I remove it to fit the sloped ring? This method drives the seal with solid hits but the seal still won't squeeze into the sloped ring
Worked perfectly
Where the heck is your plastic timing chain guide? I didn’t see them when you took the head off..
It might have gotten edited out. I had to cut down a few things in the interest of time.
👍👍👍👍👍
parfait
parfait
Would be nice if u showed us how to remove the seal itself while it's still on the bike but good video tho it helped out
To remove it I just took the sprocket off then used a curved pick to slide between the collar and seal to pull it out. You can also just take off the sprocket and push the seal in toward the case beyond the flush seal and then take the collar off and pull the old seal out.
My 17 starting making a noise like somethin was loose inside so I took the side covers off and notice my kick start assembly has a lot of play is that normal?
great advice. I used a socket and hammer technique. The seal seated too far in on one side and not enough on the other. Had to buy another seal kit since I FUBARed one set already. Will def try your technique next.
Heyyy…..I have a kx 450f 2017 same like yours, my bike is making a taping noise when I turned it on, can u tell whats wrong with it if u can
Can you do a video of a quick carb and throttle body cleaning/maintenance?
these bikes aren’t car heated brother
carbureted**
Yeah bro just found out not too long ago they are fuel injected lol
I have tried this method 2 days ago. It worked perfectly and the seal gone to its place in less than a minute. I am still amazed how this trick worked!! N
Looks to me like you were driving the upper fork bushing and seal at same time - am I correct?
Front wheel is clicking after new bearings
Всё наглядно, всё понятно даже без перевода! Спасибо!