วีดีโอ

Thank u 2 years my car has been in garage I've tried so many things it's not pretty far from easy but very educational I replaced my hydro boost and my car did fine for few day then o e day I drove few .miles and car shut off while driving I can't do test on it cause it has to go threw system all gears 30 mins so makes it hard guessing one iam a girl that's used to walls a painter cars are not for me at all please I am seeking your advice I may have been rough getting all of a d I know I didn't lock my wheel like I should of. Ut it drove few times before this temper it s in now what do u think it may be and have u ever did hydro boost the whole car is held by a clip insane way they did that going insane with trying and not knowing single mom can't afford mechanic unless they want to trade work for work bad ass with painting and house fixes not a. Car but I can and will just advice sir or your rate to fix it sorry for the lifeonv story but my hole I've dug is far worse now not having a car please help what is causing it to shut off lock mode something 817 915 9511 cell please tex call Michele greatly appreciate it and will pay for any advice if it works I will make it worth ur time please thank u god.bless thank u for video your awesome and wiser than idiots I've had try and say what it is

How do you know you're not pushing the clog further down?

Great video. This is exactly what a plumber will do for $500

Hey so I know this is an old video but our kitchen sink won’t drain. So I investigated and found out by I being covered in dirty water we found an acorn and now I’m pretty sure a large acorn is blocking the pipes. Help? From mother and daughter living paycheck to paycheck

Recently dealt with this. Found it way easier to go thru roof vent with snake as it immediately removed 2-3 bends from the route it was taking thru walls to get thru to the main drain pipe. Worked with my 25ft manual snake, and definitely ran into something nasty, but worked it back and forth at the sticking spots and it cleared.

You could put stoppers in the sinks above 😂

Why are the 2 shutoffs connected to the water softener oriented in the same direction ? Shouldn't one shutoff prevent water flowing into the softener and the other prevent water from flowing out of the softener ?

Great learning video, I got rid of my garbage disposal & put in one big sink

Big help thanks.

2:30 make sure you're wearing eye protection y'all. Don't get splashed in the eye with nasty drain water.

Very good. A little long nd meandering at the end.

Dam keep Moving it around could not see

The problem with this is your are working completely blindly, not knowing where u are, whether you solved the issue. And you have to connect and unconnect the pipe to know, it’s very annoying.

and dont forget to use gasket sealer on those paper gaskets they do not seal themselves. there paper. its mandatory

My pipes are glued I can't find a single video that n how to do mine

I believe that's high pressure switch.

Where is the high side located?

Not simple as your video suggestion. First, not everyone has the tool like you have. Second not everyone has the same piple installation like you have. Third, not everyone has issue like your kitchen sink clogged. Finally, for my issue, I must call the plumber anyway.

What quick jack is that bc x5 have a very wide spread jack point. Thx

Great job brother I’m gonna try it on my wife’s suburban. I replaced the blow motor resistor thinking that would fix the issue. I still replaced it tho because the old one was really nasty.

You know I never thought about renting a snake.. that's a great idea in gonna dry thus tomorrow thank you

Very good video! One thing to add is take the hood back and easily rest it against the windshield. It makes it easier if the hood prop is out of the way.

I’ve never heard of stressing soldered joints to failure. Rather than spend that much time opening multiple valves, I turn on the bathroom faucet to both hot and cold. Then I Let R Rip. Then turn off the water after air is cleared. But what do I know?

What did you pull out?

…I used two plungers to unclogged my kitchen sink. A sink plunger and a toilet plunger. Sink plunger to stop outflow of one side and gently plunging the non-eurator side with the toilet plunger. It worked for now 🙋🏾‍♀️💅🏾

Thanks buddy! I followed your steps and saved my 400 bucks😛♥️ You are genies✌🏻

Just what I need it I’m installing water softener. I originally wasn’t going to install bypass by I will just in case

Not everyone has this tool at home! So many people have to call a plumber!!!!

EXCELLENT!! EXTREMELY HELPFUL!! THANK YOU!!

I just did the same with a more manual 50 foot auger. I went about 47 feet, the end was full of food. Thought I got the clog, but no luck. Guess I'll try again tomorrow.

Thank you on rhe tie rod end ❤

Fuck 😂😂😂see nothing

Do you worry about using that rental tool with older drain pipes ?

This video was very helpful, clear and well done! I tried others but useless basic information. This guy was real and I like the way he presented the the solution. Hopefully it will do the trick cause we have tried the basics.

Just used your video to this exact same thing and it worked perfectly! Thanks!!

I have the same situation with the plugging of both drains, but my plumbing does not look like that. I have the huge trap on the regular kitchen sink side but I do not have a horizontal pipe connecting to my garbage disposal. Basically, my set up is split From the wall. I always kind of knew there was some thing arising, because when I would garbage disposals a full sink full of water, it would rise up on the other side with this disgusting crud water.

I sometimes wake up with a 1.

Had my instinct for 3 weeks and it stays at 5 😂

Good video, my clog must be where yours is, I will try a small snake first, Thanks.

Book time calls 4hr eachside and customers dunno why it cost soo much

I have a flopping noise in my tire I was sure it was a broken steel belt or a bearing. was told that it could be the Slime tire sealant I put in it. It's like 12 or 14 oz.

Thanks great. Do I need to buy OEM expensive. Or can I just go on eBay and get the cheap one.

Great job where did you buy this tool. Please..didnt watch your full video

Thank you for the demo and mention of safeguards! Will try to unplug mine now. : )

Good video but 90% of my jobs cost $85 not $500

Anybody can help Me out ? So I pulled out the middle piece and the pipe that’s connect to the back wall had a lot of gunk in it so I removed most of it with a broken hanger but only what I could reach, but after assembling back it only worked for a second lol. Should I snake that back piece even more ?

Why are you breathing so hard?

I have the EXACT same car, same color too! I just did this to the car and I replaced everything, even all the ball joints about two weeks ago. I did driver side first and there was a learning curve, a lot of cussing, straining sounds, grunts, etc. Then I did the other side in about an hour! It’s amazing what you can do when you know what to do!

What headers

Man, I'm dealing with this exact issue. Tried a 25-foot auger, with no avail. Getting ready to go rent a 50-footer, per your suggestion....