วีดีโอ

cool burnout.

R ya gonna build ya some sliders to replace shackles in the rear?

Question, I know you used the old 700r4 how did you do the vss or did you delete that out of the pcm? In the middle of the same swap on the same year truck

Awesome ❤🎉🎉🎉😮😊

built ford tough with Chevy Stuff!

Whats up man i have a 73 c10 im looking into doing an 8.8 swap mind telling me what that rear end came out of and is it the same width as a 12 bolt?

appreciate the video, i basically had the exact same issues with my 6L as you had with yours. lifters we're so stuck i just pulled the cam and knocked em into the engine. seemed easier lol. my cam bearings were also shot. so i knocked em out and sent the block to the machine shop... when i went to order new cam bearings for my 2003 LQ4 i ran into a snag. Our block is a transition year. so you will either need the 1st design or 2nd design cam bearings. since i sent my block to the machine shop i never measured the cam bores. Mic'd the outside of the cam bearings and just ballparked it to 1st design, if it turns out i need 2nd design bearings and you need 1st design ill have a deal for you. If i get my block back this year, been in the machine shop for 14 weeks so far.

Is the fuel pressure regulator not boost referenced or pump can't keep up? fuel pressure dropping?

How did you build your front end? Did you use chromeoly or mig it?

Real life jimmy neutron

More like 1320’😂

What brand are those headers?

What tranny?? I’ll go snoop more videos to see if I can find out.

What rear gear do you have

10/10 🤤

We’re you using flux to weld? I didn’t hear the gas the entire time 😂 You made this look really easy, I’m trying to tackle this soon. Great information in these videos 👍🏽👍🏽

Land of the living skies !!!! I've subbed for the ride !!!! I'm in calgary about to do a 6.0 swap on a 56 poncho 2 door hard top ..check my channel out too !! ...great looking engine so far .can't wait to see the rest of the build

Good idea with the glass packs on the run in stand. They knock down the noise a lot more than you'd think. Enough to hear valvetrain issues. What was the before bearings oil pressure (for comparing later)?

You post more often than I do, but I'd like to see you in your own videos more than I see you in Kyle's at least!

Great video, but you gotta work on the audio. The opening was blowing my speakers at a sane volume setting and then the rest of the video was so quite I had to crank it up

That’s gonna be a nice setup! Keep the videos coming!

Very nice build! My son is building a 5.3 for his 91 hatch!MMS suspension and 8.8 rear 4:10 gears

That’s more than 500ft😂

What cam n converter on the 4.8? Is it feel lazy with the 80mm

You young fellas have your stuff together,I watched you with the Turbo 400 and the trans brake,and now you are building a nice LS! I will be 80 this year and I better stick with the gen 1 small blocks.

What radiator bracket are you using? I’d more than appreciate to know. I need something like this on my build ASAP

Whats the cheapest and easiest way to run the stock ecu with this set up? I have seen guys running piggyback computers with there stock ecu , have you tried turbo carb set up before?

Stock bottom end gen 3 motor?

I was hoping to see the fuel basket after you modified it but it was left out of the video. All that was shown was it in the tank already. That was a missed opportunity to show some skills.

how much did the height of the C notch affect how the bed set ? Did you need to shim other mounting holes to match?

Hey man I bought white lighting for auction have some questions

What rear end gearing? Almost done with my 5.3 swap in my 85

pro ratchet is my favourite as well. can’t believe it’s not way more popular. what intake you running?

😮 not that fast

If making 700whp is one pump enough?

Where did you get the seats and the seat adapters from?

I've seen people weld the C notch plate in whats your take on that?

Love the garage build type of stuff it's my favorite

Where are you located?

Are you still rocking a Gen 3 5.3 in the foxbody? Been trying to find me a Gen 3.5 or Gen 4 but they’re either overpriced or 400 miles away lol. I can get Gen 3 5.3 for $300-$400 all day just worried about blowing them up too fast

Thanks for the video, I’m currently going thru this rn. You ain’t lyin, this shyt got me hot af 😡 😤

For some reason I didn't think the sloppy trans brake was good for this amount of HP. I'm doing 115 in the quarter in a 3600lb street car. Gonna have to wire this up. I like the arcade buttons too. Cool car.

That is so much faster than I would expect that suspension of being capable of. I'm really Impressed while also being a little scared for you. Lol

What throttle cable did you use?

What color is the truck. You got paint code?

Im prob dumb fo rasking but with the fuel pump fittings what is actually holding the fittings onto the pump? Did i miss somthing?

How thick are the plates and tabs you used ?

Whatever works and drives back

Any info on the turbo kit? Bout to sell my bike and dumping it all on my single cab.