วีดีโอ

Fancy seeing you here, I'm sure you get those comments quite often. Do arcade games interest you too?

@@VixyTreat I may have a few old arcade games at home.

Yes, i alternate from weekly to bi weekly depending on the busy times in the arcade.

​@@arcadezombie1975Gotcha. I'm kind of intimidated to do it since its been so long😂

@JPbruv I would remove it and do it outside if it has been that long. That way you don’t make a mess inside of the game, it’s not a fun clean up job. But normally I just use a bucket and use the little hose and drain the tank. If your doesn’t have a hose put one on the valve and drain all the water out. If there any water in the water separator, drain the too.

Does it have an error code?

@@arcadezombie1975 The small screen inside the cabinet says communication error with the ticket counter, but we use a card system Intercard so there are no tickets... I am also seeing that -12v on the power delivery board is not illuminated (the others are)... My tech and I are stumped. Manufacturer is of no help.

@@chrisking686 i have had that issue before with the ticket side of the game. We use CORE Cashless, i dont know how your system works but we have a harness that plugs into this small ticket board ( about an inch wide and maybe a couple inches long. I unplug the 4 pin connector and plug it back in and my ticket issues go away. I have also had what i like to call virtual ticket jams, some game have a ticket reset button and sometimes game will not say when they have ticket jams and we use a card that works with CORE and it clears the virtual ticket jams. Also, it’s easy to miss sometimes but one of the i think 4 power supplies could be bad, the game will till look like its fully powered but its not. There is a little power supply that i had to replace twice in my game. I think that one controls the ticket side. I will do what I can to help you out.

Unfortunately i do not know of a way to fix the segments, i have tried to locate the number segments and i cannot find the correct size. As far as i know Kalkomat will not sell just the number segments. You will have to purchase the entire board but i do think they have advanced replacement. You will need to call a distributor for that.

@@arcadezombie1975 that's a shame yeah I've contacted the company, they offer a service of refurbishing the board... But it does come at at cost £250 I believe. Bit steep for what it is.

Holy cow I responded twice to the wrong question, I apologize double time.

Oops I’m so sorry I responded to the wrong question, I apologize for that.

@@arcadezombie1975 thanks bud I'll have a look!

In my experience with this game, most all of its problems come from the main board. I have had all those issues you mentioned and they were all board related, Ice dose offer advanced replacement. I’m sorry i cant help you out any better.

i was looking at the cyclone today and I wasn’t sure if i seen it or not but there is a battery on the main board. That battery, im pretty sure it holds the memory. Try checking the voltage on the battery and change it if it’s low. That could be the problem with it resetting when it turns on.

@@arcadezombie1975thanks appreciate it

I agree, I just wish i knew more about board work.

I do plan on getting ICE to repair that board, i just wasn’t sure if the board was any good or not.

Yes, the jackpot grows as each player misses.

There definitely was a power issue.

?

?

Unfortunately, you can’t order direct from Andamiro, you will need to use a distributor PlayerOne/Brady’s, or Betson.

@@arcadezombie1975 thanks for this..

@@arcadezombie1975 Playerone does not carry...Betson has it.....

@@davet7231 that’s odd, I got mine from Player One, they must have dropped Andamiro. Betson is great.

That’s actually a pretty good idea, but at the moment no I do not.

@@arcadezombie1975 ok ty! I had some tech questions about games, parts ect but let me know when you do set one up

Always feel free to ask on this, I will do my best to help you out.

First lock was too short.

File it down flat.

That is correct.

Bobs Space Racer, Daytona Fl.

I had an issue like that once, it ended up being that I had loose power wire in the moles pin that went to the main board. They get beat so much, that the wires will sometimes start to break. As long as you have proper voltage coming out of the power supply it should be good, check for broken wires or moles housings that become loos over time. You say it’s a dynamic so it’s a kalcomat game, it should be the same set up. When I get a chance I will do my best to get more info for you.

@@arcadezombie1975 sweet anything helps as I’m trying to learn how to fix games because if I’m running them a tech can be to expensive especially for us vendors dealing with so many games . The guy ran carnivals so it’s been in weather as far as humidity /moisture . I did notice on some solder joints on the back of the board there is rust and since there’s no battery near any of it I know it’s moisture damage . But it’s just in a few spots so I’m guessing I need to clean the board abit and maybe reflow joints. But until I get the new power supply this Tuesday and install it I won’t know further if the board is actually damaged . I got the new supply because this dynamic is an early 2000,s model so close to twenty yrs I think a supply change would not hurt any . I’ll check the connectors more closely especially the power connectors. Also yes it’s a kalkomat . The standard black one like in their website pics for the dynamic. I know a local distributor said the machines have not changed much over the yrs so the new dynamic looks identical to the early made ones . They’ve been in business less than 30 yrs I think so none are exactly ancient anyway lol. Hope to hear anything else in the future you can tell me about these

Boxer’s are great money makers, the bad thing and I don’t know this is a trend but I do notice boxer machines outside. They can hold up to weather but they are not meant for outdoors, but as you can see even we have ours outdoors. I must have replaced the main board 5 or 6 times in the years that we have had it, it is possible water may have damaged the board. I think they do a warranty exchange but you might need to go through a distributor. The game will make its money back, people love showing off to friends and loved ones. I will do my best to help you out.

@@arcadezombie1975 right on and yeah Shaffer distributing here in ohio close to me works with them and said if I needed to fix the board to not buy new as they are 1100 bucks . Instead they would send my board to kalkomat and that would be cheaper than spending 1100 . However I’m not sure what the repair cost would be or how I get charged for that. I never went that far in the conversation . So maybe I get charged for the repair or they just send a new one out for less . Since I got this second hand I have no warranty that I’m aware of

I did see boxers at my state fair this year and see them at other fairs too so I’d say it’s a thing. Now I did sit and watch one while it was dead but then one group at a time here and there would play a lot of rounds . Fairs seem to be a good spot and there is a lot of people all day walking through.

We got 6 rides to choose from

2 black head rest

From the creators of triotech mad wave motion theater ❤

What kind of problems?

I replaced the motor but its not spinning. I get a message on the credits...27 on the Jackpot value i get what looks like a broken 2 . Turned power on and off. Is there any way to reset it? I know the wheel has to be spinning for the machine to work but I can't get the motor to spin.@@arcadezombie1975

Have you tried looking in the setting,

@@arcadezombie1975 Sorry, is there a setting that might be a factor? I tried putting the ticket related options back to default but I still only get tickets for the first game. Thanks.

@LJandLJ i have never had an issue like yours, we use a ticketless system. I had an issue where it would not pay out the bonus due to broken link between games and header. I was thinking maybe it thinks it has more lanes linked and it stops paying out. I would ask ICE how they set theirs up with your board, is it single by itself or in a row of lanes already linked. I think I remember you saying they tested it and it was working for them. Please keep me updated if you figure it out, i like to keep little notes on weird probes like that.

We use CORE Cashless, CORE has been updating a lot of their devices so what you’re seeing might be their older EOL device’s.

That is something you will need to get from Baytek, any software that I may have is not my property to hand out. My apologies.

Well im sure they will make a new guitar version and i will have to update it again. I have not had to update the. Firmware or mate the guitars since this last video. Permanent fix, nope, eventually they will have another update or become EOL. But no you should not have to mate them every time.

We have rides and I don’t work on rides unless it’s a ride simulator and thank go we don’t have any of those.

Well the balls should be replaced every 6 months, the balls will start to ware down and become out of round and that could possible be the issue. But it’s just a guess.