วีดีโอ

Grijac je spojen na transformator 220v/6v grijac treba 6.3v ali radi i na 6v bez problema

hvala

Thank you, Nice radio I enjoyed working on it .

Ovo je bilo za drzavno natjeca iz fizike u 8 razredu... skroz sam ga lose napravija , pregrijava se , nie kalibriran , mozda uskoro napravim novi ali sa 2 veca transformatora i boljim oscilatorom

FireBottle da iz splita

Dali sudjelujete na forumu diy-audio.com.hr? Tamo sam upravo napravio novi post o PCL86 gitarskom pojačalu...

FireBottle Mozee Ja trenutno radim na novom pojacalu sa izlaznom lampom 811a mozda dodam jos jednu. Mogu ti poslat slike na mail ako oces!😉😉

Dylan Cruz It is very similar. Watch my other videos!

ok! you earned my subscription :)

Dylan Cruz 😉

Hii , my amplitude display works perfectly , the sunlight was strong in the video so display was not visible . Display is green. Watch my other videos ! ;)

Thank you very much for the answer! I didn't see anything on that display in your video but if I really concentrate... :-D All the seven segment displays of my generator are red and frequency and voltage displays had the same intensity before it broke. But I already determined that UNI-T also used darker green displays for voltage in some generators of this type. Your one is very dark. ;-)

KMNO4 U=12V I=0.08A Without load Watch my other videos maby you will get idea for your next project

I bought soldering flux reclenty. Watch other videos on my channel you may like

you have link in video description

Selim Güzel I dont understand you

Thank you , you will build one just be persistent ! ;)

no , If this is to week you can make zvs driver and make coil ( 3turns 1.5m diammetar ) conect it directly to zvs driver and power larger loads ( I can power 90W bulb) on bigger distances (1m) but you must Find the resonant frequency and make lc oscillator on reciver coil

check your transmitter with osciloscope if it works you need bigger reciver coil and if you still dont have good results put capacitor around 100nF in parallel with reciver coil ! as test load use LED or small bulb or use bridge rectifier and linear regulator for good stable output voltage

thanks man.. this is really helpful

i will appreciate it if you can send to my email (dfzkl494@gmail.com) more/better pictures or videos of this work as carried out by you for viewing, follow up and clearer understanding. will be expecting to hear from you. thanks

Ezekiel Udofia Do you want pictures and video of this transmitter or zvs transmitter? If you have some ideas future projects just say.

this one not the zvs no ideas just needa good follow up my email remains.... dfzkl494@gmail.com

nije važno jel je to kristal oscilator ili s tranzistorom inace 1 kanal oscilator po mogućnosti s tranzistorom

bismarc 1 Moze mogu ti poslat na mail shemu ako oces

može

koji ti je mail ,posalji

ELECTRONICS dalmatiko@gmail.com

Omer Barznjy this is my first wireless power transmitter I dont make video about everithing I make

ok welldone. but I'm not very good at electronic. but I'm very interested on wireless power transmission. and I don't know how to put the components on the board and connect to each other. I really need help please . If you can contact me on Facebook or any other. And I also don't know what component it need .Thanks for all

first ,if you can buy bread board. you can make any circuit on it without soldering , you can contact me on ante.kekez22@gmail.com I will send you some pictures

I sent you an email

MrCarrotTv hahah thx

MrCarrotTv watch my other videos !

WildMania kakav metal ? to zuto je samo trakica koja obavija feritnu jezgru !!! ispod naljepnice su 2 feritna komada u oblikucslova E zaljepljena i omotana s tom trakicom..

Mislim na ove žute prstenove. na ploči.

one sluze za pojačivanje rerzonancije , da jezgra zavojnica na driveru su od punog metala.

thank you ;)

thank you very much !!! these comments such as yours are to me a big boost!!!

MAXX YT 😊