- 18
- 54 344
wheelrepairs
United Kingdom
เข้าร่วมเมื่อ 1 มี.ค. 2023
Locking Wheel Nut Removal
วีดีโอ
Range Land Rover Discovery Locking Wheel Nut Removal
มุมมอง 3K7 หลายเดือนก่อน
www.wheelrepairs.co How to remove a range rover or land rover or discovery locking wheel nut.
Locking wheel nut removal tool.
มุมมอง 22910 หลายเดือนก่อน
Created by InShot:inshotapp.page.link/YTShare
Hyundai Ioniq Locking Wheel Nut Removal
มุมมอง 69810 หลายเดือนก่อน
Hyundai Ioniq Locking Wheel Nut Removal 1. Drill a small hole in the top of the silver dome nut. 2. Use a small metal cutting disk on a Dremel or drill and cut a grove on the top of the dome. Use a flat head cold chisel to split the silver dome nut. 3.Remove the silver nut. Whack an impact socket onto the locking wheel nut and remove. Ps. Do NOT try and remove the wheel trim to get access to th...
How to remove a spinning collar from a socket
มุมมอง 172ปีที่แล้ว
How to remove a spinning collar or washer or nut from a socket.
BMW No Wheel Lock Key! Over Torqued!
มุมมอง 780ปีที่แล้ว
This BMW arrived with the locking wheel nut key missing. The customer had several incorrect sized spline keys. None of them fitted and the problem was the lug nut itself was well over torqued. Quite possibly twisting the bolt inside the wheel, giving it a sort of hour glass shape. Thus weakening the material of the bolt. When you try remove these even when you do get the correct size spline key...
Ford Fiesta Locking Wheel Nut Removal, No Key, No Drilling, No Welding.. Just Be Careful!
มุมมอง 9Kปีที่แล้ว
Ford Fiesta Locking Wheel Nut Removal. These can be removed without drilling or welding if you are careful. The top of this locking wheel nut is designed to shear clean off soon as you put a typical socket on the top. The top is only held on by a flimsy bit of aluminum that is designed to twist off as soon as you place a socket on the top of the nut. I used a 21 millimeter smooth bore socket, i...
Milwaukee Packout Toolbox Storage System Independant Honest Review.
มุมมอง 2.4Kปีที่แล้ว
The Milwaukee Packout, is pretty good. I've had several toolboxes over the years but all have failed in some way. I've cracked lids, broken hinges, broken fasteners and clasps. For years I've wondered why manufactures didn't produce a modular tough toolbox that lives up to the task. In my opinion this is the first system providing true rugged, well thought out modularity, providing all sorts of...
Audi locking wheel nut removal, no key, no drilling, no welding, just a smooth bore socket!
มุมมอง 2.6Kปีที่แล้ว
Audi locking wheel nut removal, no key, no drilling, no welding, just a smooth bore conical socket! When a locking wheel nut needs removing first check if it has a spinning collar. If it does not have a spinning collar then most of the time it can be removed using a impact socket. I use a set of Sealy / bluespot smooth bore conical socket. Its basically a hardened steel tube that's slightly wid...
Welding a sheared off Ford locking wheel nut!
มุมมอง 2Kปีที่แล้ว
Welding a sheared off Ford locking wheel nut!
Remove a Peugeot Citroen Vauxhall locking wheel nut without a key. No Key no Problem
มุมมอง 12Kปีที่แล้ว
Remove a Peugeot Citroen Vauxhall locking wheel nut without a key. No Key no Problem
Halfords Reverse Thread Locking Wheel Nut Remover
มุมมอง 4.1Kปีที่แล้ว
Halfords Reverse Thread Locking Wheel Nut Remover
Splitting the ring works every time,never failed,just use a bolt remover threat grips as you undo the bolt
But on a 206 convertible alloy wheel it's down a long hole and a nightmare tried welding a nut on in the end cut the wheel off in the end
That only work if locker are loose otherwise tops snap off like there designed to
After watching you idiots with your videos, as I cringe all the way through 'em, I am so, SO very glad I looked in the glove compartment where the socket was. As a side note, you tire "experts" with your 1/2" impact wrenches, LAY OFF my wheels. I'll determine the tightness of my lugs. Not you.
It’s called a conical socket?
What size would you use for a 17mm bmw key to come off
The most useless video ever on TH-cam. Locking wheel nut removal???? Absolutely useless this clip, your theory does NOT work, delete this stupid I fo-less clip now.
How to turn a 1 minute video into a 10 minute one in the most boring manner known to man.
Lol, sorry its boring..but If it helps anybody...
Them covers are to stop water and dust to stop corrosion. Not designed to sheer off
Yep.. but customers are always enticed to wack a socket on.. they are designed to sheer off.
What size socket
I use 17 or 18 mm on these
It's not a 17mm you need, the wheel nuts are 17mm, it's a 15 or 14 you need
Actually there are a couple of dif sizes ive found on this type..but the most common is 17 or 18 mm..thats without removing the spinning collar.
If you get an Alan key across the flats the same size as the hole and hammer it into the hole, you can undo the nut. This method has worked in our tool room in the past.
Excellent mate
Many thanks!
I’ve got four bolts to get off a Peugeot because the key’s been lost. Plan to weld a 25mm od tube to the bolt so I can weld on the inside of the tube and not damage the alloys. Not seen anyone else try this way yet, I could be the first!
👍👍
The method you mentioned around 4 minutes, I have tried this and the centre twisted off, leaving just the bottom of the nut, and impossible to then get off
I never had that happen tbh, but i can imagine that coukd happen if it was totally over torqued. If that happened it would be pretty easy to get off if you have a small welder. In fact i will grind one down flat and show a video of how to weld one
Any tips for one with a spinning collar🤦🏿♂️
Get a cold bladed chisel and a lump hammer, then hit the collar on the edge and it should break or snap. Then bang a 19mm socket, or one that is tight, and remove it that way.
Or buy a set of conical sockets off ebay.. they are about £25 for a full set
Which size rod did you use, Was that 1/8 or 3/32?
Can’t seem to find this generic key on eBay mate, is it specific to Land Rover?
Yep they are on ebay..generic
Yes only for range rover
lol ,,, youve clearly never come across a tight one ,,, personally I take them off with aa mig welder running about 200 amps , a copper tube a spray bottle of water and a lot of skill.
True, ive never had one i couldnt remove yet.. but if i had to weld I would go with 97 amps stick weld the 4 grooves. But havent had any overtorqued so far.. but im sure the day will come!
@@wheelrepairs I do quite a few ,,,, usually put on three or four years ago by the tire fitters with a rattly gun , I have a technique that involves burning through the outter layers and bonding the two layers together but not welding the nut to the stud at the same time , then welding a big stand off onto the lotas you work out ,,, the heat must be kept up too of course ,,, with the rim being kept cool ,,, the later nuts have a really good heat treat too and wont die grind either ,,, but like yourself , Ive not had one I cant get off yet , I charge 125 quid a time and its no cure no pay .
Fair play.. id be interested to see a video of that ...
What do I look for on eBay for the generic?
@@zazzyzander just type dynomec range rover..you will find them
the first set . i just turned a bit if brass to the lathe to go behind the ring. easy to pop them out with that
Good idea!
Any idea anyone how to get part sheared bolt garage broke out of the locking nut
Did you get it out?
@wheelrepairs no there no way to get it out
Thanks for the video good advice
I drilled out the centre and used a screw remover to undo the bolt. Hard work but worked fine. Stupid design.
Yes.. ive seen a couple of people do that.. the center stub is not very wide so you have to be careful. Yes daft design, i had to weld one out today after AA had recessed it!
How much is it to get you out to do that. Thanks. Great video btw❤❤❤
Bout 40 notes to remove all 4
How do u use em bro. Ja hammer the cu nts on?
Yes you just hammer them on..
When i say hammer I mean lightly tap with a hammer to get the first line of the thread to bite then reversing the socket will get it to fully bite.
Dus it blledin wurhk?
It will work only on a couple of sizes..
Please buy a small camera holder or tripod, this will free up both your hands.
Good idea..will get one!
Is that a brummie accent ...
Lol
Many thanks for the impact socket idea. Got 3 off my Citroen C4GP but forth was being a sod and must have tapped it back rendering it useless. Had me completely baffled until I saw your video. Regards John.
Glad it helped!
Fiesta wheels are getting stolen often?
No, but people still loose there keys...
You just casually carry a 25kg bench vise about with you 😂😂
I know lol, I bought it from a very very old lady in Wolverhampton for £20. It was sitting on an old style metal bin in the alley way... soon as I saw it I thought oh yeah baby that will sit nice in the garage.. but it ended up in the van..Ive broke it twice now and need to find a new one!
@wheelrepairs nice same ones we had way back in high school when a was a boy clocked it straight away great big vises never seen one mobile before hahaha
lol, you know.. I've really got attached to it and wouldn't want to be without it now, kinda got used to the way it thinks...done some monster work with it, but sadly cracked it in the snow few weeks back, I did weld it but cracked it again a few days back again in very cold temps. I'm going to keep it for removing bolts from sockets, but its default setting is now ramshackle bodgit n scarper.
I have several sets of reverse thread removers..they are all thin walled. The prob with halfords type is that they only fit car wheels that have lots of room where the bolt / nut sits because the walls are so thick. Plus its a two socket pack..so only two sizes! But its a real go to if you have lots if room in your rim and its the correct diameter for your locking wheel nut.Positive point with these halfords is that they will not crack! Bad news is the halfords reverse thread will not fit these type of locking wheel nuts at all. You have to physically remove the spinning collar to fit a very small reverse thread. Halfords are way to big for these.
Is a reverse locking nut remover useless for this job ?
The reverse thread socket will not work with these type of locking wheel nuts as the spinning collar makes the threaded socket useless. You would have to remove the collar first and then purchase a very small diameter reverse thread to fit over the center stud, or fit a standard 6 sided small socket.
@@wheelrepairs thanks for your response. And excuse my ignorance I did watch your video from start to finish great content and very informative keep up the good work 👍🏽
@@adrianedwards6911 All good, please feel free to drop me a comment or email if you have any problems removing yours.
If it has a spinning collar, this reverse thread socket will not work.
@@wheelrepairsmy collar came off and I can’t get the socket off. I tried a 12/13mm socket but it doesn’t work.