วีดีโอ

What a nightmare installation... Couldn't stop watching though. Like a horror movie. So basically we need a roof lift and some more "stuff" to be able to change it.. :)

I noticed some black paint at the base of the bottle jack, did you have to weld that baseplate on?

What is the model number or name of the foot control you used?

hello bro! great job done! wanted to ask for advice: i have a panigale v4 sp2 and i bought brembo rcs corsa corta brake and clutch cylinders! will the motocorsa barrels that you installed in the video fit my setup? won't they catch on the front fairing when turning the steering wheel?? what kind of clutch switch did you use with the corsa corta clutch cylinder?! and is it necessary to replace the control buttons when installing the rcs corsa corta brake cylinder (the lever will rest against them anyway)??

I love your videos my man! Great content.

Great job, looking to do a similar job on my honda blackbird. Couldn't find a video on it.

Hey i was hoping to do the same to my paigale v4s and was wondering if i could get a list of parts/instructions. Thx. Ps loved the series

i know this is a dumb question but how is the pump being driven?

Congrats on hitting your 1000 subscribers as well! That's exciting! I'm hoping my Ducati videos and my Ram Rebel videos (as well as my detailing videos) get me to 1k quickly. Video editing sucks though and that's what is slowing me down.

Looks amazing! I've already reached out to my local Duc shop to inquire about putting down a deposit for the 2025 V4S. Meanwhile, the very few bolt on mods I'm doing to my 959 have been a nightmare with finding CF parts that actually fit. I'm out of the country for a few more weeks but when I get home everything should be available and ready for me to ceramic coat, install and ride!

Gorgeous. Mine is red. My previous was the R&W 98, bought originally.

Gerat videos！

Hi there, do you have a disassembly video as well?

Thank you for this video. Did you say you'd link the Brembo part numbers for the seal kit, O ring, etc.?

Those are pretty bad ass! Looks so much better. My wife likes to ride with me on the 959. If I can keep that bike while looking to buy a new V4S she can still ride. But the passenger footpeg bracket is ugly as sin. Seen anyone make a rugged carbon fiber bracket yet?

The little 'holder' is a wrench. To screw the light bulbs into the holder. 8:50 - I mounted those blinkers on my ducati S2R yesterday both front and rear. They are amazing.

yo, would this work on a v2 also or only the V4?

I've watched a bunch of your build series. They pop up in my feed from time to time. I'm curious how you financed this build. Is this your bike or a customer's bike or is there a ton of sponsorships? I'm looking to do a build series for a V4S this winter. But it's all personally financed. Not quite sure how yet, but I've been saving. Lol!

Where did you get that engine stand!

Dude, you're a few subscribers away from eligibility for monetization!

How did you put on the winglets did you make the holes you’re self for the down wings ?

Hey man, quick question... I need to drain and purge oil before install, right? Or can I simply wait a few hours after shutting off the bike?

Just discovered your channel and the Panigale build…..looking forward to seeing how it progresses & the end result. Really liking your choices in parts/components! Also….these 3 bikes = eye candy 😍🔥💯

These 3 machines = eye candy 😍🔥💯

Where can i get this chain? I want mine look exactly like yours. Yours is beautiful!!!

Is this an original superleggera? If not,i want to know, where did you buy all these carbon parts 😂 your bike looks amazing!

Is this an original superleggera? If not,i want to know, where did you buy all these carbon parts 😂 your bike looks amazing!

Great and detail video. I am going to install Titanium ventilated pistons on my Brembo M50 calipers. Greetings from Argentina!!!

great instructions. judging by the honey its been awhile for clean fluid

What's the make and model of the pneumatic jack that you were able to retrofit to the Abba lift?

You're probably having trouble pressurizing the rear brake properly because it's an underslung caliper. The proper way to bleed a brake like that is to unbolt the caliper and flip it so that the bleeder is at the highest point while you're bleeding.

Nice work in all these videos. Appreciate the attention to detail. Where did you get that low profile pressure switch for the clutch? Do you think I can install one of those on the slave instead of the master? Also do you know if I can I install a rear brake light pressure switch on the opposite end of the hose at the ABS module?

Good job

Finally a great installation video where you don't have to see that person's face the entire time !!!!!

Where did you get that red and black sprocket setup?

Could you make a video from start to finish? Starting from taking off the fairings?

Ducati recommends to replace the tank hose, that thing will leak

The Haynes manual suggests leaving the master cylinder connected and pumping out the pistons (two at a time) with it. Makes sense if you don't have access to compressed air.

Could it run with out the termostat?

Great instructions

I just learned a new trick. Paper towel in my socket from now on.

I'm working on my 05 R1 right know. Similar build with the Ohlins suspension but I'm going more race replica. Almost all carbon bodywork including the unobtainable carbon seat and titanium and aluminum hardware. Also, Gilles tooling rear sets, chain adjuster, etc. Finally, a Boz Bros open exhaust which is jet hot coated. Beautiful job, chief

Love those wheels! Have you taken weights to compare before and after on everything you've done? Also, quick question not relating to wheels. I have to flush brake and clutch fluid. Is the same fluid used for both? Seems that's what I'm gathering so far.

Mine still leak after rebuild..what actually happening?

What is the torque please? Thanks

Please tell me where did you get that brembo master rear. I can’t find it anywhere

I just stumbled on your channel the other day. I have a 2016 959 I'm doing very basic mods to just to get some experience before I go buy the V4S. From the looks of it, you did to your V4 what I have envisioned for my build. Meanwhile, on my 959, I've been having a bitch of a time getting carbon fiber parts that actually fit! I get it, some tweaking has to be done but between two different companies, neither have made a rear hugger that works and it's costing me a lot of time, money and patience. (Ironically, the exhaust heat shield that was custom red and black CF fit perfectly!) I'm seeing your CF fairing. Was there much work you had to do to make it all fit right?

Great Video!! This helped me out so much brother. I am in the process of my build and dealing with this save exhaust cover and the left engine cover. I really didnt want to remove the rear subframe, but this made it look a little simpler than i thought it would be. Plus you reused the same subframe bolts which i wasn't sure of either. This video just helped me so much.

Why do i not see extended forks for sale or videos for v4 its like they dont exist but i know there alot of people out there that need longer forks because the ride is unbearable for taller people. Someone has to make em cause lower links arent enough.

I’ve been looking for a conversion kit from 2018 converting to a 2020+ thank you for this video!