วีดีโอ

Thanks.

Very useful information

Great informative video..Thank you for sharing your knowledge!

appreciate your video you saved 200$ today.

thank you for that video

Excellent video and helped me diagnose my leaky inlet valve.

The problem I’m having is the WiFi

Hello sir, I had an error like the one below (Error I/O COMMUNICATION), I followed your step by step and now another error appeared (Error 40:12 I/O Board Mismatch). My device here is the T5130 dryer. Could you help me ?

Please please information to my dryer Electrolux run every 5 and 10 second no vaccum .. show in displly Please help .. Please reply

good job u done good bless

Hello sir I recently bought a cpu from Electrolux dealer Group Dynamics pro. Sent them the specifications but when I received the cpu and I installed it, it brought Compact Pro boot Version 1.3 Tried reaching them out but they couldn’t help out, all that they said was that we needed their service provider physically at the washer to install the software. Kindly sir how can I sort out the issue, I’ll greatly appreciate your help

Where can I get this valve in korea?

Very helpful. I would always replace the whole thing

This was verry helpfull! Thanks a lot, and keep up the good work!

brilliant!

Model number T5130

Jampar 3 a Raha hai dryer

now I know how to disassemble the valves after I watched another video on how to properly remove the assembly for my make/model machine

How to replace I/O module 81 to I/O module type 82.greetings from Serbia

Incredible video! Think you might have just saved my washing machine.

Do you know how to remove the plastic tubing from the solenoid? For a Wascomat W620 cc. Thank you.

Very very usefull, Thank you. I was crazy why the water cant go thru even the coil works. Miniholes..

Hi there .. can you please make a video of ( How to fix error 12.2 on a compass pro ) i have this error

Fantastic! My water comes straight from a well, and every time we have a rain the water gets very dirty. The water inlet has some filters but not enough apparently, so in my cace it was just a matter of opening the valve and cleaning it thoroughly, especially those micro holes in the valves. Worked like a charm. If the problem is repeating I am considering making those micro pores a bit less micro with a hot needle. 😊 Big cheers!

Even though I have done what you said the e:14 still remain on the display board.

Hello sir, i have a problem on my T5675, i have a I/O board disordered error, how can i fix it please ? 🙏

Sir, you are an absolute legend! My washing machine had been leaking for months, and I couldn't fix it myself, so I was about to buy a replacement valve. But then I stumbled upon your video about the worn rubber on a piston and how to resurface it with Emery cloth. So, I gave it a try, and no more leaks now! Thanks so much for sharing this genius solution.

Well done. ❤❤❤

Awesome and very helpful video! Thank you so much. I was wondering how to control the water pressure on the inlet valves if possible? Especially powder wash number 4, which is the liquid detergent area. Some of our machines the pressure is so strong it leaks over the machine.

Replaced my incoming dual valve with a 'Robinson' replacement. Will not open to allow water flow. A. Im pretty sure i connected the wires as they were, ? Does it matter? B. Could it be a board issue. If so, how do you diagnose, video? C. Do i need to reset Washer after getting an H F code, due to flow issue? D. What parts might keep the valves from opening? Any help is appreciated, Thank you!

Thank you so much. Able to fix my washing machine. Perfect video.

Do you have the DC92-00658C PC board?

Hello I checked this,all good but inside of plastic unit are two small red screens that you don't show if they clogged water can not flow threw

Excellent video, however not all parts are created equal. The coils on mine were a very tight fit. I got the first one off ok, but when trying to remove the 2nd, the plastic housing that it sits over just snapped off. It certainly didn't slide up nice and easy like it did in this video - this is definitely not a criticism of the video, just a precaution for anyone trying to do the same. The inlet valve is about 6.5 years old and musn't be great quality as I also tried to remove the filter where the inlet hose connects and the clips snapped basically just by looking at them. General question: can the solenoid itself fail resulting in the piston not raising and therefore not letting the water in?

I have a Wascomat WHWF09810M - it's similar to this one but you can' take the front off by removing the lower panel. How does the front panel come off on my model?

Which one the mixing valve? I have code 45e

Thanks much for the how-to! Our unit was leaking quite badly. Went through the cleaning process and all appears well again. I would note that I had to remove four more screws to get my control panel to lay-over, two hidden under the control panel trim. Thanks much!

Samsung Washing automatic 13.0kg

Help please! Electrolux Tumble dryer Compass Pro TD6-10 has got dark display. Power is ON. Fuses (3pcs) were checked - OK. Power is presented on CPU, but display got dark. It happend after the Dryer was de-energised for a few hours.

What is the tool name? Which opens the solenoid!!!

Great video. If there's a slow leak from the valve, how do you suggest diagnosing the source of the leak? Should i just take it apart, clean it off and hope the leak goes away?

A perfect video - I learned something new, fixed something quickly and prevented a flood. Thank you!

Wow, very excellent instruction on the inlet valve indeed.

Thank you. Very helpful

Thank you!

Can you tell me please how you fix the machine when display show ( Error I/O COMMUNICATION) please help me

My Wascomat washer on pre wash cycle water come out on number one soap box. But water won’t come out on wash cycle which is on 2 soap box , do you know what is wrong?

It has taken 5 months to get a new water valve, at the cost of 93 dollars. My washer was still operating( not at true performance) but wife still able to do laundry. I kept old water valve and plan on trying to do the repair as you are doing. Thank you for sharing your knowledge on the subject

Hi there. Your video on how to check and rectify a solenoid valve was very interesting and informative. My LG washing machine's solenoid valve of the cold water inlet isn't functioning, I suspect, it ought to be due to fine particals blocking the very fine holes as explained in the video. The other inlet is of Hot water which, I don't use. The unit has 2 separate valves on either side. The one on the left is Hot water and the other on the right is cold water. My question is, can I interchange the wiring inputs from cold to hot and vice-versa keeping in mind the polarity. Will it work ? I'm a retired Maintenance Mechanical Supervisor with Shipyard and Oil and Gas experience with limited knowledge of electrical subject. As the basic work of the solenoid valve is to open and close with the right amount of water pressure and electrical power as determined by the sensor in the washing machine. So what's the hunch ? Please advice.

Thank you for uploading this helpful movie.