วีดีโอ

The service told me that the gearbox sliping in 4 to 5 but i have checked myself the presures and just the clutch E its -150 and the max its +-400 , i havent seen any sliping ,there are no fault codes on transmision , what do you think if the pressure it's ok there wouldn't be any sleeping right ?

The best video explaining why , most of the people don't know why the clutches are burning In Romania its asking 2300 euro but they dont do anythink inside mechatronics/valve body !!

Are you able to offer advice on an 8HP as well? My F30 335i is throwing a code, 420641, and it wont shift out of park. I already ran in ISTA diagnostic, which told me to replace the mechatronics. I swapped out the valve body and the EGS and virginized/coded it to my car, also replaced the mechatronic sleeve, the transmission pan, filter, and fluid. Yet my car still won't shift out of park. I can screw in the emergency neutral bolt on the side of the transmission and that will put it in neutral, but if that isn't screwed in and I get into the car and just try to put it into any gear, it automatically shifts back into park. Any advice would be greatly appreciated.

I have a sound that comes from the gearbox when I let off the gas at lower revs

😂😂😂😷😷😷😷😷😷

What spark plugs n wires should I use too many to pick from

Hope someone can help. i have a 2011 335xdrive auto with 100K miles. Only mod is MHD S1, not raced or abused. The trans had a leak and I wasnt aware. The Trans would have fault and go into limp mode. When I took to shop they found with only a few quartz in it. They replaced fluid and filter- car drove but felt some slipping still. Trans alarm still active. They opened pan again and changed the seals. They changed seals and still have slippage between 3/4. The shop is german car specialized in porche but not diagnosing right being they are doing it again now to change solenoids. Do you think the slippage is solenoids being the trasmission fault still active?

Many thanks for the detailed, but succinct explanation on how to service these transmissions. Thanks again Victor.

Hi Viktor, Wheres the high pressure release valeve on a 6HP 21? My 2008 528i lost almost all the transmission fluid from March 2024 til about June 2024 when I stopped driving it to protect the transmission. Im changing the pan and the fluid with genuine parts right now and I cannot figure out where the flui escaped from. I degreased the whole undercarriage in June and I can see oil leaking from the pan but the oil level is fine. The tansmission maybe had 2 qts in it plus whats in the torque converter but the pan is moist with oil, not ATF. The vehicle had been driving great even when losing the fluid. Is the drain plug the actual high pressure release valve and thats why it creaks when you turn it to remove it? Thanks in advance.

Hello, I have the same transmission on a 2006 740i. The transmission shifts smoothly during acceleration, but during braking or downshifting, I feel a jerk from going to 4th to 3rd or, possibly, 3rd to 2nd. It feels similar to driving a stickshift while downshifting to 2nd and letting go of the clutch quickly. Any idea what that could be?

Thank you, thank you, thank you!!!

If there is no such thing as a BMW transmission does BMW drive directly from the motor to the different 😂

❤

This guy is spot on. I changed the solenoids, bridge adapter and those other 4 rubber tubes but never actually opened the valve body itself to change those little dampers inside and the plate. And guess what, after 1 year the gearbox has a small delay before it engages D or R.

What about the convertible? The connection in the dash is different…

How are you doing today sir I need your help please I have a Bmwx5 30d so my outomatic gearbox got a problem with a clutch plate so please help with clutch kits please 🙏

And thats why manual is the best

Smith Mark Robinson Cynthia Lewis Matthew

To everyone that hates on BMW just remember this transmission isn't by BMW and almost all 6speed auto cars use this exact same set of transmissions

They dont this is rare

I have a question. Do these vehicles have map sensors? if so, where is it located? I gotta check engine light and it told me to change the map sensor.

This guy obviously is a professional and knows what he's talking about. Excellent job bro

Basically you get rid of the POS car at 70,000 mi... No thanks, I'll just stay with my trusty manual transmission and avoid this crap altogether 😂

Damper kit for 6hp19 asap

We did this repair on a 2011 X3 35i 2:33 - had to remove intake. Replaced pump - did not replace intake manifold gaskets because son didn’t want to spend to extra money- car runs good no but it only idles now because the gas pedal doesn’t work now - any suggestions? Thank you for the great video.

sorry buddy but your soviet accent is annoying but good work

is it better to just replace all the plugs & coils , my f01 running so rough has 136mls

Hey, where are you located ?

Proud the be the owner of an 04 E46 M3. I take care of it better than I do myself.

Take advice from a guy with a face diaper 😂

Hello, would you happen to have a picture where all the black check balls goes in the valve body? I have 6hp21 manual shift, and the separator plate is 063. Thanks

What size of walnuts for the blaster and the procedure for this. Thank you

Excellent video in real time. You're an awesome instructor. Will this be exactly the same for a 2011 X3 35? Where is your shop at and how much doe a job like this cost? My son is in Texas and I have to get it done for him. Thanks in advance!!!

evil company's setting a trans to a vin sad but true

I have the same gearbox and it locks in 3rd gear and lights up an error for the cruise control You leave the car and come back later, it is not blocked Does anyone know what it is, I've been suffering for days

Thanks for all the inofrmations. To be more complete, early N55 have also this same kind of hpfp. (I have mine to replace, that's why I'm here.)

I have a rare BMW M3 Sport Estate 2003 for sale. Needs restoration work.

Hey! I have a 320d with the zf transmission and from 1500 to 2000 rpm sometimes if I accelerate hard the car starts to shake. I have to stop accelerating and accelerate again to avoit the shaking. What can it be?

Maaaate. You’ve just given me covid.

Don't listen to him. Do the service yourself, it is easy. And you will save lots of $.

Come over and change mine please.

Hello Victor, I have a 6hp19 on a e90 335i. I have a clunk when I start the car in P (th-cam.com/video/nAo5arh7K-A/w-d-xo.html), there are no errors and it shifts as its supposed to. I did a service, ZF service kit(oil,pan,fresh fluid) didn't make any difference. can you give me some advice? thank you

TQVM Well done Video

Yes thank you this video is so well done you are one hell of a smart guy thanks so much for this swap info...i have an e46 04 m3 smg just finished now the wiring, thanks...

Who & what the fcck have you done with the stitching on that steering wheel!!😳 That looks absolutely awful!! The carbon interior….. seriously WTF!… that looks so cheap & shite! I have two of these in my collection, silver grey & Phoenix yellow, both have lower that 40K on the clock…. You’ve made a great car into a have wagon!! Personally I’m glad you don’t work on any of my cars!!

Hello, i replaced my bmw f10 meter with used one, then it shows red dot same like this video and make my player always restart, can you fix this?

How did you get to that back screw !? It's the only issue I've run into right now

Hi guys... how's part3?

Great car! Nice job! Could I get more info where you get all the parts, please?

Excellent video!!