วีดีโอ

Why not change the other side wheel bearing also

4:10 I struggled with that step for hours bc I didn’t know how to do the rod until I seen this video and in less than 5 minutes I was done

Looks too bulky

You saved me from buying a full on cover for my project k5. The rear window on my blazer didn’t go up and it’s raining season in Northern California.

You should’ve sanded the entire panels with 600 grid and cleaned it with the degreaser and then adhesive promoter and then the product. I did it to my my 2005 GMC Yukon and it looks spectacular. It’s been two years and it still like I did yesterday

I have two 3500 4/4 square body Crew cabs BB AUTO FOR SALE

Installed one on my K5 CUCV as well as the XJ shaft, made a big difference.

Hey @TheBlazerBeam, what size bit was in your drill? What size rivet nuts and what size screws did you use? I just got that rivet tool, I’m still learning.

Well made video brother

What moter

Lol bro, this works great, except the cab reeks of wheel bearing grease now😂

Does the motor have to go back in a certain position I have a pure and saying fault in "motor hall" E7

Dude thank you for the video this is a topic most people don't cover , I would suggest getting a propane blowtorch you can get the propane canisters for camping. I always use it when metal Parts won't budge, a little Heat actually is my go to before WD-40 obviously using heat to get parts out that you're just going to throw away. Thanks again

More people need to be able to find this video

Threw one on my Springfield XDm clone the other day. Works fine. Boom!

I'm glad I found this tutorial on the GM tilt wheel steering column repair. I had the 4 reversed torque bolts almost ready to fall out. As I disassemble the column, stuff was falling /flying everywhere. I was just about ready to give up. 🤔 After reviewing this a couple of times it started making sense and I was able to complete the repair. Thanks!

How do you go about removing

10/24 Thank you so much. Could not find where tension pre- load spring went. Watched lots of videos. This was certainly the most helpful. Thanks again for great video.

Wow man. Thankyou. Must have seen 100 videos with the hellcat pro or the osp which have the screw holes on top to easily install on optic.ur video was perfect. I love that gun so much and now that im starting to carry more and more my hellcat has turned into my everyday carry. So thanks

Great I dropped the spring down the hole

idk what to do i tuck it all a part an water got in it an it dry out i was geting e 10 erro an i got a new screen it work but win i plud the wiers throw the neck just a little the screen shut off it i go left or right the screen shut off so in short the key holder wiers as well as the multy meeter wiers must be shorting out to the fream is all i can thick of if that one wiers was grownd to my fream sir would that stop it from going on and if u where me wood u unplug every think buy a new key holder an plug the screen with batter it shuold light up idk what elss it can be

Did you do it with or without the adhesive promoter?

Idaho is right over the river from me, freedom mags close.

Jeez, this music. I thought 2 videos are palying the same time.

would it be so difficult to set the phone camera horizontally to get the most out of the screen size?

Holy crap!....you really kept my biscuits from burnin....and that amazon link fer that pivot tool was super.....thanx

Looking at doing the same for my ghost.... in your video, you put a straight stem on... the original arrangement had a couple inches rise at 45 degree. Just wondering if you see a big difference and if the bars feel to low?

Why do people call the optic a "red dot"? All the ones I've seen are green...no joke.

I have a Road Runner RS5 Pro, both motors are making a knocking noise. I wanna replace the bearings. Wondering if they're using the same size bearings...

looking for advice on an issue with my air pro 2023. it shut down on me last week and hasnt turned on since. i just replaced the charging port today and it still not working, but the charger reads green when plugged in, before the port change, it wouldnt even plug into it so im at a loss now

As others have commented, A great video demonstration, very well presented, including torque specs! to the point, no BS, tips, color loctite,.... (I didn't know about the color difference). Thanks, I learned a lot today! the only thing I need to figure out is which red dot fits my application. Update: I just watched your Holosun HS507c video and will consider that, thanks again. I like their green dot option. A friend suggested the Romeo-X. More to look into.

I just got my ADE advanced optic in the mail today after waiting through two delays being sent the wrong one the first time and they sent me the wrong goddamn one again. I swear these people are clowns The amount doesn't fit and the optic doesn't even sit down in there where it shows too long. It's possible I'm doing something wrong but I don't think so.

First

Lmao I know how you feel I just did this it's a pain

Thank you. My 78 GMC window just stuck 1/2 way today

How did u fix the leak?

3:25 is there a link to a website that sells this modification? If so please send it. Thank you!

Will this work with the borgeson steering box?

hey buddy thanx for your schooling on that steering column my c10 was down for a week went around looking for a whole steering replacement.but i saw your video and man with alittle patience and taking on the job.its not that hard.one guy wanted 400.00 to rebuild it.i did it for 34.00 and change..thanks again..

I think you just stripped the extender.

Will this fit on the xdm 5.25 in 10mm?

5/16 is better to use to remove the old terminal

Do you have email to show you my trailer hitch. Can I save it or not?

will it work on the 5 inch slide?

Thx I really love it

Wow! I’m so glad I found this video. I’m reassembling mine in my 88 S-10 tomorrow.

As a really skinny guy the only place that my handgun is comfortable, in the majority of cases is 6 to 4 o’clock positions, appendixhas to be the most uncomfortable position for me personally as well as risking exposing my fire going for anything in my front pockets

Is it legal and is itconcerned modifing just want to be on the safe side thank you and who can do this in fresno?

I bent my rim on my Solar ff lite , new wheel and rim is coming installed already but I have to put the hub on the new rim . As a novice you think I can do it on my own are do I need to take it to a shop?

Bro, a brand new motor wheel would cost only a couple hundred, your time and tool purchase is way more worth than that