วีดีโอ

Thanks for the video! What happens if I have a BTT SKR E3 Mini V2 motherboard on a CR-10 Mini? Would I have to modify the klipper configuration for my board with some specifications of my printer? thank you!

Ugh this is too much trouble. Might as well just buy a new G604 -- which will also break down in a year because of the cheap Chinese OMRON switches Logitech uses.

So i took the mouse apart first, before finding this video. I didnt know ee had TWO micro springs inside.... 😰

When I get to the point of issuing the "pscp" command I get error message "ssh_init: Network error: Cannot assign requested address" and I don't understand why. Please help.

Thx for the help!

I applied WD40, as minimal as I could to the button underneath. Double click, plus and minus shortcuts not working; are now a thing of the past!

yeah....im just gonna get a different mouse. good on you for being patient.

❤❤❤

buying linear rails gave me headace. I checked Aliexpress. But you dont know what you get and comments may be fake.

What a lot of work to get to the PCB, glad I have a space 604 so I can take my time.

how to make it work with klipper?

great video but fuck it i'm gonna buy a new one

What do you call the soldering tip he used? It's like a fork or something

got the job done

Das die Amis immer so nusseln müssen. Ich spreche hier in Schweden Nu auch den tiefste skånska dialekt...

i have a screw leftover? always the same with DIY

I have upgraded my one with a brushless fan motor (150W 25,2V) which is available for 5 bugs only and fits in without any modifications. The vacuum cleaner is now more powerful and less noisy.

Mine is less than 2 months old, and has already developed multiple cracks around the nozzle where the extension tube slides in. It has done less than 2 hours of use, spot cleaning around the house. It is very obviously not the correct grade of plastic for this use. I would not recommend buying one of these as they are not fit for purpose i.m.h.o.

The entire mouse! Lol. Thanks for the video-I'm never buying one of these again.

How many screw driver type to do all of this stuff?

does the on /off switch lock on or has to be pressed while in use?

just completed my G604's repair. Here's to hoping it lasts long enough for a proper successor to appear.

when i enter /dev/serial/by-path/* it doesnt work, it says there is no directory with that name. ok i figured it out. i had the wrong STM chip entered. make sure to double check your board to make sure you have the right chip

surprised mine lasted as long as it did. It broke last year and making the effort to fix it now

This video is maybe the only thing online available now on how to install a hemera! Why does e3d not have any guide on their own products?

once i enter biqu as the user it doesnt let me type. EDIT: i found the answer. it just doesnt show what you type and i wasted 10 minutes of my time being angry because putty has a dumb password feature.

Hi do you know if this will work for the ZV-1F as well?

This sophisticated design seems to be a good way to implement the planned obsolescence. The easy fix for such an issue (in my case unexpected double-clicks) is a drop of silicone grease or so. I am using 5-56 and it works fine with most of the switches - can forget about the issue for a year at least. The only issue with this mouse in my zoo - it is very difficult to get there. The first G604 mouse I returned under the warranty. And the next issue happened a few months after the warranty was expired. So I got to fix it. But I did it with a syringe that time. A couple of years gone and it is sick again (along with the old M325 that is constructed in a way that much easier to access and lubricate her switch). This time I got the paperclip (peace of wire if you wish), sprayed a bit of 5-56 into a tiny cap, got some of the solution on the tip of the paperclip (that I slightly bent as a bow), and entered it into the gap between the left button and the housing from the front of the mouse towards the back. As it seen in the video from 4:00 to 4:05, the white switch button is situated somewhere in between the + symbol on the auxiliary button and the center of the wheel, so you got the idea where you have to poke the oily stuff. As long as there is a sufficient amount of the silicone grease on the top of that button it will find a way to get into the switch and lubricate/clean/cover the mechanism and contact points inside. I spent a few minutes poking and now back to work enjoying prompt response without unexpected double-clicks. I hope the Logitech company will change the way of manufacturing and would not celebrate the planned obsolescence, but will please the users with a long-lasting devices as it used to be in the beginning.

what if I only want to use it for clipper screen for remote control?

Thanks! With your guide I was able to fix my double click issue. My first time soldering project was successful!

how come mine wont connect to my WIFI?

Hi, can u make a Video how u install the BLTouch to the Chiron and which Firmware you use ?

my package is lack of ducky :(

It uploads everything except the language file. An error message appears. Display V3.0.1 Everything is fine on the V3.0 display. Do you have any idea?

What's the point of this upgrade if the print quality looks the same as stock?

After typing "make menuconfig" I get this response "make: *** No rule to make target 'menuconfig'. Stop."

thanks this guide helped me fix my g604 and its double clicking pita!!

Hey what size are the belts?

You don't need bags but filters.....

Which switches can i use for G4-G9?

amazing !

Hello, how to recover when the electricity is cut off?

was going to order the tft35 then seen it does not work with klipper then was going to use my rasbarry pi. into i seen a pad 7. seen your video saved video liked video shared video. you shown me everything i needed to know and made it very easy to understand thank you. also i got a sunlu in the corner over here. steppers dont work d.o.d going to turn that into a bigtreetech setup next. so asking. there is no need for a pi3 or 4 with this. just the pad 7 and a skr mini e3 3.0 ?

Thank you, this was the most helpful video in this topic.

In case anybody is trying to fix the middle mouse button because it doesn't click anymore pay attention at 5:30. In between the springs you'll have to cut a slit open on that orange protective cover with an exacto knife so the little disk comes put. The disk is supposed to be dome shaped not flat. Just take a ball point pen and press into the disk until it looks dome shaped again. Not too much or else pressing down will feel too stiff. Wrap a narrow piece of electrical tape around the disk and board to seal and secure the disk. Thanks to the reddit guy that suggested this and this channel for showing us g604 users the path to repair.

Hinestly... I just use the heat gun and they came out easy lol. Works like a charm now, thank you got the video. 🙏🏽

Thank you for this. I just got the BTT Pad 7 and this was everything I needed to get it up and running.

The thing I don’t like is that you cannot block the trigger. Have to pulll all the time. To bad because autonomy so good with 18v battery

Hi! do you have a tutorial how to use the ADXL34 that is included with the BTT Pad 7? i'm at a loss here on how to use it.

i just lifted my pointer click mouse button and used a cotton swab with alcohol on my switch and it hasnt had the problem since. take battery out.