- 35
- 452 464
Omar's car parts replacement's + more
เข้าร่วมเมื่อ 7 ต.ค. 2015
2013 dodge challanger
Door latch malefunction quick fix, driver door outter doorlatch wont open the door, simple fix unless repair is required.
มุมมอง: 18
วีดีโอ
2014 Ford Edge Starting
มุมมอง 875ปีที่แล้ว
2014 Ford Edge starting issues. Apparently it seemed to Have a bad starter until I found out that the key was the problem . Don't waste your money check your key first.
How too replace 2001honda CRV idle air control valve
มุมมอง 42K4 ปีที่แล้ว
How too replace 2001honda CRV idle air control valve
How too go fromYellow too clear headlights
มุมมอง 825 ปีที่แล้ว
How too go fromYellow too clear headlights
2013 Audi A4 Quattro Ambient temperature sensor
มุมมอง 18K5 ปีที่แล้ว
2013 Audi A4 Quattro Ambient temperature sensor
2008 land rover lr3 v8 hse rear airbags+ strut replacement
มุมมอง 1.9K5 ปีที่แล้ว
2008 land rover lr3 v8 hse rear airbags strut replacement
2013 Mercedes c250 High Pressure Fuel pump installation.
มุมมอง 46K5 ปีที่แล้ว
2013 Mercedes c250 High Pressure Fuel pump installation.
Part 2 2013 Mercedes c250 High Pressure Fuel pump installation.
มุมมอง 8K5 ปีที่แล้ว
Part 2 2013 Mercedes c250 High Pressure Fuel pump installation.
2013 Hyundai Veloster turbo right upper engine mount replacement
มุมมอง 5K5 ปีที่แล้ว
2013 Hyundai Veloster turbo right upper engine mount replacement
How to replace 2015 Nissan Altima SV rear wheel bearing
มุมมอง 14K5 ปีที่แล้ว
How to replace 2015 Nissan Altima SV rear wheel bearing
How to replace passenger upper right motor mount 2013 explorer xlt
มุมมอง 21K5 ปีที่แล้ว
How to replace passenger upper right motor mount 2013 explorer xlt
How too replace lower control arms on 2014 Chrysler 300c hemi.
มุมมอง 10K5 ปีที่แล้ว
How too replace lower control arms on 2014 Chrysler 300c hemi.
How too reset your engine oil, brake lights, and service after youve done a tune up, on BMW 535i 11
มุมมอง 235 ปีที่แล้ว
How too reset your engine oil, brake lights, and service after youve done a tune up, on BMW 535i 11
How to remove and clean throttle body, on 2010 to 2013 camaro, on rough idle
มุมมอง 46K5 ปีที่แล้ว
How to remove and clean throttle body, on 2010 to 2013 camaro, on rough idle
How to replace or locate crankshaft sensor on 10,11,(12),13,14 chevy traverse 3.6l awd
มุมมอง 63K5 ปีที่แล้ว
How to replace or locate crankshaft sensor on 10,11,(12),13,14 chevy traverse 3.6l awd
How to replace motor mounts on 11,12,13,14, buick enclave, chevy traverse, saturn outlook and acadia
มุมมอง 29K5 ปีที่แล้ว
How to replace motor mounts on 11,12,13,14, buick enclave, chevy traverse, saturn outlook and acadia
How too replace thermostat housing 2013 ford fusion 1.6l EcoBoost
มุมมอง 65K6 ปีที่แล้ว
How too replace thermostat housing 2013 ford fusion 1.6l EcoBoost
How too replace turbo bypass solenoid 2013 ford fusion EcoBoost 1.6l turbo
มุมมอง 37K6 ปีที่แล้ว
How too replace turbo bypass solenoid 2013 ford fusion EcoBoost 1.6l turbo
05 06 07 08 jeep Grand Cherokee 3.7L Upper Control Arm replacement
มุมมอง 4.7K6 ปีที่แล้ว
05 06 07 08 jeep Grand Cherokee 3.7L Upper Control Arm replacement
Does p050a have anything to do with this?
@@trumanknowles5989 check your iac valve and check your air filter it could be clogged or dirty
@trumanknowles5989 the throttle body fill make a very different symptom when turning the car on. It will start then shut off, but if you have a rough start/cold start, check vavle and air filter first
@@omarlopez-eb2nd but isn't that on the throttle body?
@@omarlopez-eb2nd where is the IAC???
@trumanknowles5989 hmm good question 🤔. Idle air control system. Let me check I'll be back
Bro... that is the KNOCK SENSOR. Are you serious with this???
@@Itsbuiltbyben some say it is, others say it is not.
Great video. Thanks, bud. 😎
Where u buy urs at i need one is it oem i need oem Amazon dorsnt wirk
@@RobertLopez-d4y ibthink we got it at Honda. Call parts and they will ask for the vin to get you the correct part.
@@omarlopez-eb2nd I checked Honda number for it online for this part n checked on Amazon they had so many but wrong numbers I came across with the number hopefully should work paid 70 for it thanks lot I appreciate u hitting m back up
@RobertLopez-d4y should work if you got the part number correctly. Just make sure not to get frustraded while instaling the part lol. Easy work.
@@omarlopez-eb2nd thanx brother
is that leaning normal?
This guys a ding dong….
I have a female plug above my harmonic balancer what's it for????
@@timothycruea6904 do you have a engine hot a/c off code on your dash.
@@timothycruea6904 check around with the loose cable to see how far it can be reached. Hopefully you find the sensor it should go too. I would have to look into that section myself lol
❤❤❤❤goed
Thank you for changing your experience, my question for you, why you replaced HPFP ? You have error code or misfiring or what the reason ?
@@chrisisho2557 while you hit the gas to do overpass, the car would go into limp mode, ypu would have to shut the car off and crank it on again to work normal. We got a used one and it did the same thing again. They ordered a new part from the dealership and it worked jist fine afterward
@omarlopez-eb2nd thank you for your reply, because I have hesitated over 4000 rpm with high Term fuel trim and I don't know, replaced low pressure fuel pump and filter but still the same, you think high pressure fuel pump or fuel injector ?
@chrisisho2557 hmmm have you checked your sparkplugs?. When problem with hpfp, the engine has low power to just to get you to a safe parking area. Also have a look at your coils see if any of them is not working correctly or starting to wear and tear.
@omarlopez-eb2nd actually, I changed all spark plugs but still the same, I put fuel injector cleaner , after two weeks show intermittent misfire cylinder1, honestly I feel something related to fuel delivery
@@chrisisho2557 or a relay could be heating up perhaps. Something electrical could be taking place aswell. There was a case on a clk 200 mercedes that had a bad fuse box. It would stall the car and it would act as if the engine was not working well.
Awesome video but i need to know what tool did you use to get the top bolt?
@@malcolmantoine3451 i have too re watch this video too see what i did lol
I used 2 long extension and a size 18mm socket, with a breaker bar to break the nut loose. Then i replaced the breaker bar with a regular ratchet too remove the 18mm nut.
Thanks for the video. My Honda crv 2001 automatic will idle and stall when stopping in the red light or intersection. I was trying to replace the IAC valve and I found there is no coolant line connected to my IAC. I am not sure if it’s missed or not. Is it necessary to have the coolant line? Actually my car has serious idle and stall issue when engine is cold. So every time I need to warm up first before driving but now it is getting worse because of stalling at stop. I really like my CRV and it runs no problem when driving. Thank you
Hey same vehicle, whenever I turn at low speed rpm’s go down and I feel some shaking on the side I’m turning to
Amazon auto parts air control valve how much prize
Great video thank you!!
On the squeeze clamps use zip tie use plyers first then put the sip tie on while squeezing
Hello did you have to loosen ac compressor to get to the bottom bolts of the thermostat housing??
You should call this video "installing the air intake manifold" You have the wrong title for your video.
What a pitty you did this video missing the most interesting parts in fixing this common problem of Mercedes C class especially . The most interesting part is how you remove everything and how you install it back not forgetting to rotate the crankshaft to the 52°mark .
Thanks, brother! Huge help!
Thank you!
But I don’t know why it didn’t start when I was gonna go home from work, then hit buttom of gas tank and start rite up too
I try to solve my 99 crv because motor quites on me whenever it wants to, serveral options for me either replace ignition switch harness or fuel pump relay, or distributor, dig into coil pack, I switch distributor from my 01 crv still rite up, looking into TH-cam a guy replaced fuel pump relay so I did and start rite up
Fuel’s not gonna squirt out
I don't recall fuel squirting. But if so it shouldn't be too much
You talk way too much. Just get to showing the mechanics
I ma so 😔 sorry, just mute me thanks for watching bless you
Can the ambient air temp sensor throw a check engine light?
Thsnk you s.r
Used your video today, thanks very much!
Glad too read this. Thank you
Thank you!!!
My spring is In the way of the bolt on the right side how to get it out
Pull the mud flap off qnd use a wrench on one end and use a rachet on the other end. Let me know if you got it off.
$50 amazon
🤔🤔🤔🤔🤔 Its been a long time since this video. Refresh my brain please. Lol
Bro you are way over using that cleaner !
Its never too much lol. But i know lol i just love the way it works and the smell lol. Thanks for watching
i have a P1508 code (iacv circuit malfunction) however my 01 AT cr-v idles perfectly fine. i replaced the IACV twice and the car is idling as you described if it were broken (code stays). when i put the original old one on it idles normal again. any thoughts?
ummm.... yea.....all that needs to be removed is the air box, lol. The ecu gets moved over a bit, but can stay connected. Takes less than an hour.
Based on the dash and radio, that's not a 2014 Ford edge.
Q se debe que el mismo.eje trasero uno compensa 50% menos que el otro, ambos suben la misma altura
Creo deven suvir al la misma altura. Si no, va a quedar desanivelada la camioneta.
@@omarlopez-eb2nd si suben igual pero no sé si es que se daña el comñensador, aparte demás bolsa de aire
@@iglesiacasadejose6137 el compressor de se daña solo si no corta, se sovre calienta. Pero igual tiene unos tipo aniveladores que se atoran cuando no suve bien la bolsa. Ahi replasos de amartiguadores fijos. Solo que es un poco dificil de instalar.
@@omarlopez-eb2nd gracias por responder, la consulta es si el compensador se daña aún cuando las bolsas están bien, si funciona aparte de las alturas
Was trying to diagnose my crvs rpm flutter at idle and was trying to figure out where to start in fixing the issue, this just pointed me in the right direction. Thanks!
Hopefully it works for you boss.
Can the pump be repaired?
I've heard that repaired will only last a shorter time, but it depends who you send it to.
Is there a reparation kit available? is there a video how to repair? parts?@@omarlopez-eb2nd
@@jaimemarun2841 hmmm im not sure i would have to check on that. I will ask a repair guy and ill get back at ya soon
Thank you @@omarlopez-eb2nd
@@jaimemarun2841 well there is no kit to repair here in the valley texas. Amd it is best to replace with new hpfp, unless you want to pay again for a refurbished one that will most likely break again sooner than later.
Thanks Omar sure is a lot of work just to change a thermostat.
Minimum 3 uur max 5 uur
That was awesome man. Really helpful.
Thanks for watching
Can you do one motor mount at a time or do have to loosen bolts on all of them before jacking up the motor when replacing them all. I have a 2010 gmc acadia with bad transmission mount but figuring rest are probably bad as well. Thinking about trying to this my self. Will be doing it with jacks and jack stands on my garage floor. Thanks
Check them first. They say its best to replace all. But if the others are good , no need too replace. Loosen them first but dont remove them untill yoi jack the engine up first.
Just fyi the one you put on is for the 2.0L engine not the 1.6 like the one you pulled off. Good video tho
Did you have to drain all the coolant?
No i just refilled it as needed, then bleed the air out, wich took forever lol. Bit of a pain those engines
@omarlopez-eb2nd yea thank God it's been good. It's my daughters car so I'm doing my best to make it right. It has a small leak from the housing so I'm replacing that and the valve that bolts to it as well. I see a video and a few mechanics local are saying I can get to it with just removing the alternator so I'm starting that route first.
@@rafaelvillanueva7403 best of luck on your job brother
Can you use a manual transmission IAC valve on a automatic ? The price difference between the two is like $100 more for the auto vs the manual. They both look exactly the same part though. I am trying to replace for 1999 Honda CRV EX AWD 2.0L. Also is yours automatic and do you have link to the new part you used? At all Autoparts stores Advanced Auto Parts, Orielly's, and AutoZone it is $257 or so for the automatic tranny one and like $158 for the manual tranny one. I don't get why the price difference is so much!
Im not sure on that bro. But i think the part came from RockAuto.com. Quality parts and replacements. Just have to decide if you want to wait on the part to arrive. But if the part look ls the same and says on the description that it fits your car, only then you should buy. Check out RockAuto.com. look at the prices to see wich is convinient for you.
@@omarlopez-eb2nd Thanks bro and great video!
You had me on you can wriggle it 😏 New sun here 😃👍 Anyways I'm here because I'm having this issue. I will replace both motor mounts but I will be replacing thee entire front suspension to the last 🔩 bolts. I have all CV axels and hub assembly.
The plug has been rigged to fit that's why it didn't have the proper ends
I figured lol. 😂 i remember i had to get the pig tails from a junkyard to make it work lol
And how exactly did you get thar bolt out with shock tower in the way?
There is a washer nut on the other side, i think i removed the undercover to access that one washer using a wrench.
Thanks for the great information ❤❤❤❤
Great info. Thanks for making a video on this replacement.
I have the exact car like yours.. Same year,,same mark,,same model,,same size,,same everything Last time I changed the bypass housing hose with the temperature sensor cause of leaking coolant by the engine was overheating.. And it's still overheating of missing water coolant.. I didn't check the thermostat yet
If you havent done so. Call ford dealership and give them your vin, you might have some recalls. This particular model is something els
Some cars have recalls for some over heating issues might want to check it out, I did mine but after a few years it’s starting to do the same thing now I think I need to change the thermostat
My Honda 2001 is P1508 actual Idle Air Control Valve Circuit ???