วีดีโอ

I’ll be honest, I expected them to try to weld the broken cast axle tube and straighten the axle.

انگار قسم خوردین ی کا رو به بدترین شکل ممکن انجام بدین. بستر کار پر خاک ، بدون نظارت و به شکل تماما هیاتی . یعنی انگاری اینا تو ی کره دیگه زندگی میکنن . ی بوکس بادی آخه چیه ک ندارین ی دست ابزار مناسب چقدر هزینه میبره یا لباس کار مرتب آخه هزینش چقدره . خدایا به تو پناه میبرم

Tis but a scratch!!

우리의 파키 형님들은 못하는게 없네 물론 정밀성 떨어지는건 감수해야 하고 수리후 보증과 AS는 당연히 없지

These people brilliant

原形が…残っているのが フレームとタイヤだけ！？

Hourly maintenance has been strictly observed on these machines and it shows….

ماشاءالله ابداع الله يعطيهم العافية ، باكستان 👍🏼 💚🇸🇦🇵🇰💚

Não seria melhor trocar a cabina ?

It must have been quite an impact to break a tractor in half, hope the driver is OK!

차 하나를 그냥 해체하고 새롭게 한대를 만드네

See the problem is it’s in two pieces…

Obviously suffering from to much TLC which let the trailer down.

ՎԱՅ ԵՍ ՁԷՐ ՄՈՐԸ ՔՈՒՆԵՄ

Bli cabin baru jh,tk pyh nk repair2,buang msa je lh bodoh...🙊

Se e aqui no Brazil já vira sucata .

15:30 What torque setting do I set these bolts? As tight as you can manage with the lever!

Ya know, I was thinking; maybe you wouldn't have accidents if you took all that crap off your vehicles, it's not like you'll lose it in a parking lot of a stadium.

معدات التصليح { تقليدية } ، لكن نشطون في العمل

Torque wrenchs are so overrated and that motor is as clean as a Kia motor should run for a good couple weeks

und immer schön das Öl auf die Erde😐

emezing ZF😮

Eu admiro esses caras, realizam qualquer trabalho árduo com entusiasmo.

@FabRats In my mind I hear the guy tightening the piston rods saying "click click ".

Дай им из рельса трактор они сломают

Totalny permanentny CHAOS !!!, ciągnik cały ustrojony jak wóz cyrkowy, ale PODSTAWOWYCH ŚWIATEŁ DROGOWYCH I KIERUNKOWSKAZÓW BRAK!

these people dont know the difference between using equipment & ABUSING equipment.its no wonder everything is junk.

This may be a dumb question, but with the wack that engine block took, combined with spinning parts coming to an instant dead stop, isn't there a good chance of that block being warped, or microcracks that could turn into major cracks?

Koszt przewyższa wartosc

Ten złom co wiezie do naprawy to był gruszka do wożenia betonu. C

Reparan gruas y no tienen una para colocar la llanta?.

You guys do great work, but you should invest in air tools you guys work on this stuff and big trucks all the time it would save you so much time and wear n tear on your body

Ohhhhhhhhhhhhhhhhh ma che è successo qua ? Hanno piegato tutto?

I've never seen a ZF break like that...but,then again,Doosan is junk anyways....sell it and get a Gradall.

Brand new crankshaft and oil pan WOW

Я думал они по привычке заварят и двигатель и коленчатый вал.

Я худею с этих ребят. Они даже на спец технике, которую не так просто перегрузить, умудряются ломать оси.

Без рессор ломаться будет постоянно!

C'mon guys i'm all for saving some coin but reusing piston rings???

I believe almost all those bolts in that engine have to be torked to a specific "pound" psi.

How do you fracture a crank shaft?

A good work, but i see only durt and mud. Why dont you clean the floor?

🇹🇷🇵🇰🇹🇷🇵🇰🤙

Nothing whatsoever to do with overloading it....said no-one ever.

Well done lads great job 😊

Do you know if they enforced weight limits on vehicles half the country would lose their jobs

Ну и где же тут "восстановление", бородатые лгунишки в шлёпанцах? Замена сломанного узла на новый есть, но никаким "восстановлением" тут даже не пахнет.

Good job 👏

Which technology?

Место слома по сварке ? Варено не раз ?