วีดีโอ

Took my bumper to a shop and the paint is scratching off already and you can peel it. They said it was my fault and that they dont prime bumpers. SHops are supposed to prime bumpers right? lol

I'm glad i live in the south. I don't have to worry about snow, salt, or my vehicles getting rusted out like this

Nice what tip you use for clear

Roughly how much $ in labor is floor pan replacement

How do you access the firewall to run wire into the cabin?

I really love this thank you very much.

Appreciate the video! You did a great job of showing how to go about it. Going to tackle my conversion 4x4 truck and replace them.

Huitlacoche, pronounced weet-la-COH-cheh, is a fungus that grows on ears of corn. It is also known as cuitlacoche, corn smut, and Mexican truffle. It is a plant disease that causes smut -multicellular fungi with many spores - to grow on maize and is a delicacy in Mexico

Glad i found this video. Was about to paint over my "pre-primed" bumper. Will def hit it with adhesion promoter now

I read through all comments, does it not bother anyone else about using 18 ga. For the frame that your K member bolts? I would think that that structure is 16ga at least. And is that EMT conduit for the crush sleeves? I commend you for your effort but I think you need to look for more strength.

After you blocked it with 600 did you have to shoot primer back on it?

Wow absolutely amazing

What do I do if I don't have those fancy spray guns you have? I just have cans of spray

How do I get Tuff Coate off the exhaust system, it's over spray and the car is 40 year's old and orginal galvanized exhaust system?

Good job I learned a lot

I have a 91 Fox Body and need a similar repair. How much was that job and how can I contact you?

You should not use wax and grease remover on plastic and do not use a red scuff pad.. Use the grey one

I am learning. This is great.

I sprayed the adhesive promoter and then the primer filler. After drying, I noticed it left like a rash like feeling. Do I have to start from scratch again?

How long have to wait after the clear coat, to do polishing.

Gawd sake. I honestly didn’t know things had to come this far down. But thanks for posting, this is exactly what I needed to know. Im gojng down the least I can manage

👍

You mentioned waiting 10 minutes before spraying the sealer, but what about delay between sealer and base coat, plus the time between base coat and clear coat? And if I end up needing to sand the sealer coat because I'll be using a spraycan primer, how long should I wait before and after sanding the sealer step? Thanks for all your guidance!

Glad you know about the 2k urathane , I tell everyone I can, that the Best for the $$$ I know of works Awesome also ! I've painted 3 of mine with it ! 😁 Good luck ! ✌

Raising them right!

I got my 70Skylark in primer already back halved and fiberglass fenders bumpers and hood. I grafted on a stage 2 scoop, did door pins, aligned the panels. I must have had about 40-50 hours into the prep work and then I payed a pro to shoot it shadow Grey. Much respect keep up the videos I know it takes a lot of extra time to document. Just remember that like someone taught you, your videos are helping others.

Great attention to detail!

Amazing work

Great videos I appreciate your hard work and helpful advice! Keep up the great work and I know how much time it takes to make these videos.

Do you prefer a basecoat clearcoat or a single stage paint the best?

How you set the air control knob. Did you open all the way or just a little.

Thanks for making this video, very informative, i found rust on my driver side shock tower and was worried but watching your video relieved my stress.

Way better then Netflix

Is thinning out the primer by 10% to make it a sealer crucial to your claim on the pre-primed bumpers? If so, what are you mixing it with to thin it out? It looks like there were instructions on the UPOL primer can but I currently don't have all the tools for proper measurements. Again, if this is a step you don't recommend skipping to back your claim, then I'll go ahead and do more research to find out exactly what I need to thin it out ...or can i just use primer for this whole step? 😅

Thanks men Good luck and success work

My turn 😬

How do you fix a bumper that’s chipping

Nice job

Good video, just wondering why you didn't make the Nov in one piece instead of all the pieces.... that's just more welds on inside from the outside that you can do nothing about.... I'm about to do this same repair. I'm going to try to video it. Hopefully.

What is the name of the undercoating you used with a paint brush?

i want to know exactly where the water is coming in from. fixing the pan and not fixing the root cause will just repeat itself.

I thought adhesion promoter was only used on raw plastic ?

Is the bulldog flexible bumper paint stripper ok to use on polyurethane?

I have a 72 GS and will be doing a lot of this same work unfortunately. Would you share where you got your replacement panels from?

Is regular primer considered a sealer or is it different?🙏🏽

Do they sell a sealer in a spray can? I’m doing rain guards, and a spoiler kit. I’m in the scuffing stage. I was going to put adhesion promoter, then use a 2K primer I have in a spray can? Is that sufficient, or do I need some kind of sealer?

I have a question this is now my second car I’ve had to have panels replaced and painted from an accident. I had them both repaired at caliber collision, not sure if your familiar with them but they get there panels and bumpers from a place called Keystone. Both times I’ve had to have them repainted because of the paint just peeling off. They always want to blame it on keystone. Don’t you think they would know how to prep those parts properly like you do or do you think they’re just taking short cuts. They’re supposed to be professionals and do it right the first time I would think.

USED BUMPERS OR NEW ONE ARE EASY TO PAINT PRIUS?

Good video, Im getting ready to do this on my 94 chevy. Very informative and you take the time to explain things. thank you.

Great video. Would love to see the finish product. I do have a question. I used the upol 3253 primer.. and I was told that it’s a direct to metal primer. So when I follow people’s videos it is kind of hard because type all use epoxy primer first and then the 2k primer before sealer or paint.. when I’m sanding I hit metal instead of epoxy primer. I was also told that you cant put body filler over the upol primer so do I have to sand those spots back down to bare metal in order to use body filler