วีดีโอ

Unfortunately the motor only vibrates. When I adjust the potentiometer for ampere regulation I still get no rotation only vibration. Is there anything else I need to set? I am not an expert Motor 17HS3401S

Hello, if you can help me with something, I bought a controller exactly like yours, I would like to use it on a rod motor that pushes and returns, the problem is the following, if I put the motor on directly, it pushes my part, that is, it has the necessary force but if I connect the motor to the controller then it seems to have no force to push the piece, my question is why? Does the controller have a force setting or something, thanks

Your videos are the best Geekguy! Just wondering is there a way to trip the motor to go full speed with a button or switch without Arduino?

Will the SMC02 work with the nema23 stepper motor 2.8 amps?

Thank you for the video. I noticed that when you pressed the CW button, the motor turns CCW, is there a way to correct this?

hi, this is good controller, is there any way to make it 5axis or more, if it is please advise how to do that. thanks

Do stepper motors run cooler with driver is set to less steps per revolution? Do stepper motors run cooler with driver is set to less Amps? I am using Nema 23 57x57x56mm, 23HS2430B, 57BYGH056 Using DM556 Driver ZK-SMC01 stepper motor controller AC 110v to 24v Power Supply 20A Max Using on a machine that runs for hours at a time. Motors run feed screw at constant speed one direction then the other direction for 10 minutes before reversing then repeats. Driver is now set to 2.7A -1600

Trying to understand F2 and F4 setting to run turn pulse numbers greater than 9999. It seems the H number set is the method but how to quantify it? I am not understanding this….. Can anyone offer me advice or even a link so I can get a handle on it PLEASE. Thank you…….

Great video! Very Informative. will this process work with the NEMA34 12NM

hey, can i controll Smc02 with esp32 on the mobile app? i have the smc 02 unit and i'm trying to make this working wirelessly for a cablecam device.

Hi what other Driver's will this controller work with this? Will the DM542, I understood your explanation about the problem, but I don't understand which words I should look at in the description of products to know which Drivers are compatible.

Great review, thank you very much

Thank you for video. In program 3, are you able to set a maximum 3 that it will not exceed? Such as you don't want someone taking it over 100 RPMs. Thank you

Дякую за освітлення багатофункціонального контроллера для управління драйвером крокового двигуна.

También quiero preguntarte si sabes de que amperaje son los fusibles. No consta en el esquema y no cuadra los montados con los de repuesto. Un saludo y gracias

He pensado cambiar los 2 termistores y los 3 reguladores de velocidad

Buen video. Yo tengo 2 tarjetas que no regulan una me la enviaron en garantía y duró 2 horas el torno gira a máxima velocidad

The screen is flickering on my one. Buy cheap buy twice...

Mine works …but it doesn’t display 0000 initially ..just LLLL .. What world that be ?

Worked through your video in detailed steps. I have an issue in that for mode 4, and probably others instead of running 1 and 2 turns the motor goes 7 turns. I must be doing something wrong, but what. Set to defaults and adjusted per your setting for dip switch but no joy. I am running out of hair to tear out. Also, if I may. What is the H inF2 and meant to do……Regards. Chris.

Excellent. Had to watch your video several times to tie down the principles. The on line manual is the usual Chinese version of English so hard to follow. The wording in the tables makes sense when one knows the principles but is useless as a teaching tool. You have filled the gap for me. Thank you.

My motor is just vibrating. What would that mean? EDIT: Just adjusted the pot for the amperage down and it is moving now. How do I fine tune the pot to get the best amperage? I've gone down till motor stops, then up till it starts, then a tad more so when i try to stop it with my finger itkeeps turnign solidly.

Thanks for such a wonderful video. If I changed the F9 pulse number parameter to 640, does F2 and F4 need to be changed to 6400 ?

I have 2 SMC01 and 1 SMC02. I would like they are start or stop at the same time. Please help.

Can we link one SMC01 to another SMC01 so we can start or stop 2 motor at the same time? Please help. thanks in advance.

Hola buenas noches, en español no lo tendrías?

Thank you very much for your great videos. I have a question: is it possible to set up an automated continuous movement of the actuator from one dead point to another with this controller without manual pressing CW and CCW buttons?

will Nema 14 with TMC2208 driver work with this controller?

Do you have a phone number so I contact someone for more information that you can share please. And Thank you!

Fantastic video. Thank you.

Buenas señor….puede explicar el funcionamiento en español?

Hi I'd been thinking to use this driver for telescope tracker. As per thermal performance, will the driver hold when used for more than 30+ minutes at low speed with 24V/1.5A?

Is there a possibility to manually reset the counter, so that after the count is finished, the next count starts again from zero? Is it possible to do this using one of the buttons or does the counter have to be disconnected from the power supply?

Excellent explanation! It's so nice to see the settings, parameters, and then the results. Thanks so much!

Hi. I have a question. Can you change the display with racing gauge tachometer for car?

how can i add a foot swich to the controller , so i can control the stepper motor by foot with two swiches cw and ccw?? Can you help ??

Great video. What is the voltage of controller Dc+ and Dc-? Is it same as the driver 12 V, or not ?

hi i need a prebuilt one. i will buy it. tell me price

Muchas gracias. Muy bien vídeo para los que tenemos este torno y mo tenemos ni idea de electrónica. Es increíble todo lo que entiendes, para mi me suena a chino jajajaja. Porfavor dime el enlace de alispress de la placa por si se me rompe un dia. Un cordial saludo y muchas gracias

Is there any way to have the driver start the stepper motor automatically after a power out?

Hi there in forward and reverse pin can be imput to signal and not whing ani com for hand wheel encoder encoder had A,B witch is reverse and forward ????

Can i can add multiple steps for clockwise and also for for anticlockwise??

I'm new to step motors and the controllers, do i have to connect the external driver to use the end stops?

Good functionality for low price. Maybe a use it for air compressor startup decompressing for light start, conecting alarm out to air valve.

As an American with hispanic heritage, fluent english speakers tend to take for granted how difficult the english language can be especially when explaning technical details. Thank you for this video and the effort you have invested into educating us.

Great series of videos. Please stop saying the word "basically".

Hi there im wondering if can help me with some information but how can i contact you with an email? If is possible thanks

Hi there Nice presentation, but im wondering and go in circles because I don’t know how can do this , in this set up how can you add up for manual mode with mpg hand wheel encoder if want to turn manual ?

Is it possible to drive an AC servo motor with a pulse generator without a driver?

Das das beste Video, dass ich zu diesem Controller finden konnte. Viele Dank dafür. Das Verstehe alles, ohne ein Experte zu sein. Sehr gut!