- 37
- 247 145
OutboardsandToys
United States
เข้าร่วมเมื่อ 21 ต.ค. 2020
Outboard motor and small engine work this is for entertainment purposes only work at your own risk I only wish to give you a little extra help along the way thank you have a blessed day
Dale Earnhardts edition intimidator impeller+run
just a quick video on where I'm getting on the intimidator
มุมมอง: 57
วีดีโอ
7.5hp gamefisher carb clean sears Ted Williams Tecumseh
มุมมอง 1.9K11 หลายเดือนก่อน
quick video on how to get to the carb and do a cleaning
The mower got some upgrades new exhaust, tires and a new pulley.
มุมมอง 172 ปีที่แล้ว
The mower got some upgrades new exhaust, tires and a new pulley.
Outboard Thermostat Issues not peeing or getting hot
มุมมอง 24K3 ปีที่แล้ว
Outboard Thermostat Issues not peeing or getting hot
Nice little bug in there
Man been trying to rebuild my 7.5 for awhile now just took off the flywheel tonight after pulling it all day with barely any spark in the mfer I found the spark plug wire connecting to the electrical box is fried so I’m hoping that’s all it is 🙏
Just going to ignore your torn float lid gasket?
what fuel mixture for this engine is 1:100 or 1:50
Thanks brotha great video
Your bowl is missing the gasket that sits on the bottom of the bowl.
This motor is still running great today
@@outboardsandtoys8413 great to hear! I got a 9.9 evinrude from 1992. Had the worst time trying to get it to run. I rebuilt the carb 3x over, new plugs, wires, ignition coils, power pack, fuel pump, water pump, thermostat, took the block out and replaced all major gaskets and still wouldnt fire/hold idle. I ended up using pb blaster small engine tune up, and bam, now runs great. All that work and it was gummed/carboned up.
Super good job buds. That's some reality right there. I sure appreciate. BC Canada in the ocean. Thank you very much.
I didn’t see any gaskets when you took the carb apart, or on the intake manifold. We’re there any gaskets?
these were great engines, very smooth and powerful
Is this efi?
What. Did you use to remove and install those doors carb nuts. Such a pain in the ass
Hola buen dia tengo el mismo motor..arranca y cuando acelero el motor se para..como si se quedara sin combustible..el carburador esta perfecto..sera la bomba d nafta??? Me seria util una ayuda
Great job on this video, good detail
Great choice of music……
Great video thankyou! But I’m still having troubles…. Any ideas on the next troubleshooting check?
Just bought a boat with this motor. Now I feel confident to do the carbs.. THANKS
I just replaced thermostats and opened the heads to clean the passage lines and it's still peeing warm water.. 81 Johnson 140 V4
What year is that motor
1960
I really like how the carburetor comes off after removing the choke leaver. Easy peasy.
Thanks for the video but can the thermostat keep the motor from Peeing? I've clean the pee hole and it still won't pee. Do you have any suggestions for me? Thanks
Sounds nice, How fast. ,On mine 40 same year, 60hp carb, add timing,cup 17p got 35mph
Thanks for this video! We just bought an 88 ranger 393v that came w a 6 cylinder 87 Johnson 150. The oil injectors removed to run 2 stroke. This is my first bass boat and power engine, so I'm trying to learn as much as possible. Again I'm completely new to motors, sometimes she seems she's a little rough on idle so I thought, hmm maybe the carbs need cleaned
Need a “how to” video Before i just start drilling 😅
I just bought this same motor but it's missing the plate with the serial and model number. Do you have them on yours, I need to replace a few parts
Do you have the model number for this, I think that I just bought the same one from fb market place and I need to replace a part., but I cant see any model numbers
I know this is an older video, but did you happen to know what year this motor was? I just picked up the same exact model yesterday and it needs a starter
How many starts will you get out of this without the battery dying?
Hi...I have a question for you 😇 It's possible to modify a 9.9 Johnson (Year 2005) to 15 hp...?? I need a new carburettor, and what else..?? Thanks... E greetings from Italy..😇😃😉 (excuse my terrible english)
You wouldnt happen to have that bracket and recoil do ya? Need to do reverse of what you did. (going from starter to pull start) Great video!
Thanks man good video
Very often we take youtube postings like this for granted. I have a 1993 15 HP Johnson, and I wanted to clean the carb. Your video enabled me to get at the carb in 5 minutes ! The little metal rod was the clincher ! Thank you very much !
So does the water go through thermostat before it gets to tell tale? Why does it need to close? What is the negative of just removing it and having water flow around head at all times instead of only when thermostat opens?
On a 2 stroke its ok to run without a thermostat and yes it will still pee it controls the water going through the jacket on the head u just cannot remove on a 4 stroke that has a computer the downfall is that it keeps the motor temp regulated for easier start-up during winter other than that u won't see any other changes other than motor running cooler
Thanks for the video, I am working on the same motor, rubber tip is worn out, searched high and low for a carb rebuild kit. Thanks
Thanks for the video, I have the same motor, I've searched far and wide for a carb rebuilt kit, can't find shit, rubber tip on needle is worn out. Thanks
Very good description. My motor gives problems at the start of every season. Also the gear change lever breaks if you lay the motor down on that side. Will never buy another Mercury. Yamaha for ever.
Im glad to see that with 3 people. I just bought a 30 for my 16 V.
The 2 cylinder 30 is amazing, the 3 cylinder 30 is even better.
Is it easy to rebuild ?
Yes very lmao I can do it in probably 10 minutes
Very well explained. thank you.
Thanks for the video I just bought one for $50.00 with controls and a stand, He took the throttle actuator off of it for another outboard, it has 155 lbs of compression in both cylinders
Wat did u do to fix tha idle i have that motor and we i put it on slow it shuts off
Adjust your air screw on the carb start at 1.5 turns then adjust from there
@@outboardsandtoys8413 is that the slow speed screw
@@treasurewithmnrs yes
@@outboardsandtoys8413 ok thanks
Where are you located
south Fulton tn
I have one of these runs great but it's the slowest motor I've ever used lol
Good video
👍
What year is motor?
99
So sick. That thing would be awesome with a big tiller handle
Yes sir had to send the prop off to get worked cause they didnt make a high enough pitch for it running a 19p on a 48hp
Choke removal 5:25 and install 14:05
antique is 100 years or older.
Do it for dale brother
Great 👍👍👍