วีดีโอ

custom 850mAh pulled from a tattu 4s pack. yes xt30. full build details here: intofpv.com/t-1s-beast-toothpick-based-on-amax-1303s

That’s because of the motors, not vtx. Your hdzero quad freestyles way better than this, but this quad shines in image quality. All about preferences!

Yeah I had challenges too. Here is the build thread with esc settings dump: intofpv.com/t-o4-65mm-whoop-build Also here is the link to the latest version of the AM32 firmware as Alka hadn't udpated the repo for 2.17 from the original factory 2.03: intofpv.com/t-cli-dump-for-tbs-lucid-aio-at32-7a-1-2s

@@stuffbymatt583 thank you! I All motors are starting up. Do you have a PID dump...no matter what I set the PIDs I get terrible oscillations trying to just hover. Did you update the betaflight from stock? I cannot get in DFU mode. This AIO is unlike any I have used! So far I am running 75mm O4. Is the 5volt 2A bec any good on this fc?

@@ChrisLBradly great to hear! try the uav tech whoop (1 & 2s) tune and try turning down master multiplier. Running factory stock 4.5.0 on this. In the cli type BL, that will reset to bootloader mode without pushing the boot button. Also check the manual misprint for the uart, info in my dump thread I linked to. Haven't tried the 5V2A bec on this, it might work but doubt it.

@ thank you!!! I played around with the PID sliders and discovered after only turning the D gain to 1.35 stopped the crazy oscillations! Now time try preset tunes. thanks again! 🙂

@@ChrisLBradly awesome to hear!

thank you, I used the tbs lucid 1-2S aio: intofpv.com/t-cli-dump-for-tbs-lucid-aio-at32-7a-1-2s

yeah it's sucks but 2min is the new 3min for digital in this size.

27k kv are power hungry

@@stuffbymatt583not true, I fly digital Walksnail whoops and get around 3:45-4 minutes easily. I would bet that lite air unit is more meant for a 2s for the best performance. That new DJI lite air until is to heavy for a 1s

Analog is still the place to be for tiny whoops. (I love my o4, just not in 65mm)

I use 550 mah batteries modded into the 65mm betafpv frame, It flies really great and I get 7 to 10 mins with my setup.

thank you! build thread here: intofpv.com/t-o4-65mm-whoop-build

yeah have ordered three! lol

good question! yes I did. I set osd warning to 80deg. Also on the cross style 5A aios these motors would push them hard and they would come down quite hot (the aios that is). the tbs lucid aio is 7A/esc so I feel it has better wiggle room.

@stuffbymatt583 what temp do you think is actually safe? Anything < 80C? I'm planning to use them on a 35mm prop o4 build. I've found on 40mm props it gets too hot too fast 🤔

@@ddxdezx90 degrees is the limit for me, my hdzero aio whoop with pids to the limit flies around 70-75. Digital builds can be hotter due to the VTX as well. Analog builds shouldn’t get super warm as u fly.

yeah opens up a lot for gorilla whoopin!

It’s in the new meteor 75 pro 04 it claims to get 5:30 minutes of flight time on a 550 too so that must mean that you can fly a full pack before losing video like a traditional 1s system I know 1s has been a issue with the voltage not being sufficient when battery is half full for DJI 04. The board itself is only $40 if you want to give it a go

ty man!

Which exact exact board are you referring to? If I am not mistaken about the weight difference between those boards is 0.1g The BEC is 0.4g ...

@@Nurek07 That's my bad I thought the lucid was a bit heavier

I’m also planing to use one of these 3d printed mounts. Do you mean basically putting the foam on the o4? How would you secure it in place?

Thank you mate. Excellent points you make. The new AIO is here: betafpv.com/collections/brushless-flight-controller/products/matrix-1s-brushless-flight-controller-hd I didn't know it existed till now! haha. Looks good. I use AM32 as I like the 32bit power from the escs. They provide more power to the motors than 8bit escs do. That's just my view though. As there is a tradeoff for weight. Whilst not in the video I did put a piece of foam tape under the camera, on the vtx. :) The killer is this 31mm format is just now viable, whilst it can actually pull it off - quad needs 80% throttle for hover. So going up in kV makes perfect sense. Those poor 300mAh packs though, lol...

@@Nurek07 betafpv.com/collections/brushless-flight-controller/products/matrix-1s-brushless-flight-controller-hd It's new. I just found it myself.

ty!

who 'dis? lol... prolly from intofpv?

thank you man, the screws are M1.4, self tappers, 12mm length. I think I originally got them in the Walksnail 1s lite kit as they are longer for whoops with digital vtxs.

Melbourne mate. South east. :)

Flight time is tricky. I think I can get up to 2 mins with triblades and the 25K motors. Throttle is crap though at 80% hover. This was just a proof of concept really. 30Kv motors would improve flight performance and reduce throttle hover but will kill flight time.

The higher kv would just reduce flight time

@LoganimFPV Okay Thanks

@@stuffbymatt583 Your thing would be to find the balance so that the flight time does not die and that the gas is at 50% in hover.

you're welcome mate, it's a bit rough and ready but I just wanted to quickly share that 1S is easy on this vtx with the right BEC.

Thank you man, the Mrs is a horticulturalist, and it shows!

Thanks, glad you like em!

I don't myself but there is info in this thread: intofpv.com/t-1s-beast-toothpick-based-on-amax-1303s?page=2

@@robertyoung534 thankyou mate!

yes fair point, I dropped my responsibilities for a bit there.

good stuff! please post a link back when ready mate.

cheers man, ty!

hah, fair point! I should get out more.

@mattheww9656 sorry I misspoke, it is xt30. Thankyou for the feedback!

build thread here: intofpv.com/t-1s-beast-toothpick-based-on-amax-1303s

ty!

@lefunetyjc will do, give me a day to post on things verse and give you the link

@@stuffbymatt583 Thank you so much! Like your design very much!